Since Atwood is no longer in business and all newer water heater models have transitioned to a smaller cutout you're not going to be able to reuse your current door and will have to make modifications to the cutout hole in order to mount a new unit. Since everything will be covered by a new access door it doesn't have to be pretty but you will need to frame in a new space within your current cutout hole for a new unit to mount onto.
I recommend going with the Furrion RV Tankless Water... view full answer...
To install a Yakima roof rack on your 2021 Honda Passport you need at least 50" JetStream Crossbars # Y00425 and the TimberLine Towers # Y33TR or the Yakima TimberLine FX Roof Rack # Y78UV that has ore or a clamp style connection as opposed to the straps.
If you don't have either of these setups then I can't recommend using an alternative setup even if you're able to get it to fit.
A while back we had someone fit a roof rack to a vehicle and while it technically "fit" and stayed put,... view full answer...
The DeeMaxx Disc Brake Assembly # DE56YR that you referenced comes with ceramic brake pads. Not all of the yellow brake pads are Kevlar. We actually sell yellow and stainless steel backed ceramic brake pads from DeeMaxx. view full answer...
We currently list both truck models in our fit guide. The new body style for the 2019 Chevrolet Silverado 1500 is listed as such while the older body styles is listed as the 2019 Chevrolet Silverado 1500 LD. With you having the new body style this will use the K-Source Snap & Zap Custom Towing Mirrors # KS80930. The older model 1500LD would use the K-Source Snap & Zap Custom Towing Mirrors # KS80910. We have images with both sets of mirrors on the product pages where you can verify based... view full answer...
Hitch accessories end up being mostly secured horizontally in trailer hitches by the tongue weight of the accessory instead of by the hitch pin which is why hitch pin locks like the # e98881 are not not rated for shear strength. At some point it would fail, but in reality it would be at a weight that would be higher than your truck would be rated to tow. view full answer...
I spoke with the Furrion techs and they stated that the USB drive would have to be a minimum of 16GB and that if it had any files other than mp3's that it could cause an error. Just to make sure you're doing everything correctly you'd first turn on the stereo and allow it to boot up, plug in the USB drive, the USB icon (fig.1) should light up and then you can press the input button to switch over to USB for the source. From there if you have any folders the folder icon (fig. 10) should... view full answer...
An LR error for the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System # LC358590 indicates an issue with the left rear jack, a hall signal issue (open ground/short, or other malfunction) or an unexpected high amperage current stall (meaning the battery stopped providing power for some reason).
You'll want to begin by checking the fuse on the control module # LC304136 for the left rear leg to ensure the fuse isn't blown. From there you'll want to trace the wiring back to... view full answer...
The Andersen Ultimate Connection 5th Wheel Trailer Hitch System with Adapter # AM3200 technically could be used to connect to a gooseneck trailer, but the ball would sit much higher than normal gooseneck towing and make the trailer too nose high. If you have base rails the better option would be the Curt Spyder Gooseneck Trailer Hitch for Fifth Wheel Rails # 16085. This would mount into the base rails and give you a gooseneck ball attachment point. view full answer...
The portion of the Ventline Ventadome Trailer Roof Vent # V2110SP-24 that will sit within the ceiling is approximately 7/8" thick so you should have no problem with your 1-1/4" thick roof, but you will most likely need to trim the garnish ring a bit to fit properly against the ceiling. You'll want to pick up a Roof Vent Installation Kit # 344270KITW as well since there isn't any mounting hardware or sealant included with the vent. view full answer...
The center pin on a 7-way is typically going to be the reverse light and the 12v hot lead is typically going to be in the 1 o'clock position. On a 6-way the 12v power pin is the center. Some times manufacturers already install the charge line (especially on newer models like your 2022) so you might not even need to install the # RM-156-75. With the engine running I would use a tester # PTW2993 on the 7-way 12v power pin to see if it already has power. If so then you're good to connect the... view full answer...
Yes, you are able to use a Synthetic Rope # BDW20095 rather than the Steel Cable # DL24104 on the Dutton-Lainson Hand Winch # DL10954. The image below shows how the line needs to be routed on the drum of the winch. view full answer...
This a very common problem even on newer vehicles like yours. The solution is to either made a thread tap like you mentioned or get one from a hardware store to clean the threads out. You can also try wire brushes and other similar solutions but the thread tap gets it done the easiest and would be what I would recommend. view full answer...
I would not recommend going with the Rhino-Rack Roof Rack Legs # RRRL110S5-2 over the # RRRL150GMC-2. While both are gutter mount options, the # RRRL150GMC-2 have been confirmed to fit and provide the proper roof clearance for adding crossbars to your 2017 Chevrolet Express Van.
As for the crossbars themselves, they are an "overhang" style. So if the roof of your van is only 59", then you can use the Rhino-Rack Vortex Aero Crossbars # RRVA150B-2 (59" black) or # RRVA150S-2 (59" silver).... view full answer...
If you're looking for an idler hub, the # 84545UC1-EZ you looked at will fit. The heavy duty Timbren Axle-Less Trailer Suspension # ASR1THDS01 uses a larger spindle with a 3,500 lb axle bearing combination. If you would like a hub and drum assembly, you can use the # 84546UC3-EZ along with the # 23-468-469 for brakes. view full answer...
Yes, there is. To add a gooseneck hitch to your 2023 Chevy 2500, I recommend the B&W Turnoverball Underbed Gooseneck Trailer Hitch item # BWGNRK1020. This kit includes custom brackets that mount in preexisting holes in your trucks frame. This system has a 30,000 lbs capacity and includes a 2-5/16" gooseneck ball that can be flipped over and stored inside the hitch. It will fit both the 8' bed and the 6-3/4' bed lengths without the OEM puck system.
I have linked an installation video below... view full answer...
Yes, I've attached a wiring diagram for the BaseCamp Hydraulic Leveling System, which depicts how the Lippert Polarity Reversing Solenoid # LC118246 is wired into the system. I'll also send a link to the installation instructions for this system separately so that you can review it. view full answer...
I do see the etrailer Trailer Hitch Receiver # e98902 you purchased for your 2020 Mazda CX-5 will also fit your new 2023 Mazda CX-5. The Replacement Hardware Kit # RHK will provide you with new hardware for the this receiver. Be sure to enter this hitch number when ordering the hardware kit to ensure you get the correct hardware. You will find the instructions for the receiver linked below. view full answer...
Idk exactly how you got to that specific page but it's only including the Yakima JetStream crossbars # Y00425 and Landing Pads for Yakima SkyLine and Control Towers # Y00233 and does not include the towers needed.
For a 2015 Kia Soul with a naked roof you would need the following components:
Yakima JetStream Crossbars - Aluminum - Black - 50" Long - Qty 2 # Y00425
SkyLine Towers for Yakima Crossbars - Fixed Mounting Points, Flush Rails, and Track Systems - Qty 4 # Y53TR
Landing Pad 22... view full answer...
I do have a solution, but the VL404 key is not something that we carry. Based on information from other customers with similar key codes, keys for this lock are no longer available. The best option is to replace the door handle completely. If you remove the handle and check the dimensions of the cutout hole to we can find a suitable replacement.
For example the Global Link RV Entry Door Locking Latch Kit with Keyed Alike Option # 295-000002 will install in cutouts that are 2-1/2" - 3"... view full answer...
Lucky for you, Swagman actually make a fat tire adapter for their Swagman XTC2 Bike Rack for 2 Bikes # S64670. What it sounds like you need is the Swagman Fat Bike Tire Wheel Adapter for XTC 2/XTC # S64674.
This adapter will replace the stock wheel holders and will give you the ability to fit up to a 5" wide tire. view full answer...
Go To Results