The Derale Snap-In Radiator Adapter Fitting for GM # D13035 you reference is in fact made of aluminum, and is just as strong and resistant to heat as before. view full answer...
The Curt jack part # C28304 is made in China.
We do have a similar rated and style jack, the Dutton-Lainson part # DL22683, that is made here in the US. This jack has the same 2,000 pound capacity and 15 inches of lift. It's also a weld on jack that swivels just like the Curt. view full answer...
We do offer a USA-made hitch ball with specs similar to the one you referenced.
B and W offers their 2-5/16-inch hitch ball # BWHB94004. This has a gross weight capacity of 30,000-lbs, a 1-1/4-inch diameter shank that is 2-1/2-inches long, a fine thread pitch (12 TPI) and includes the lock washer and nut. All heat-treated parts have a raw finish. view full answer...
The wire in the Jacketed 2 Wire, 10 Gauge, Brake Wire, item # 10-2-1, is stranded, and designed for automotive applications. The temperature rating on the coating is 221 degrees Fahrenheit. This allows for use of the wire for up to 40 amps at up to 25 feet.
This is the wire we use to wire the brake output wire and the 12 volt power wire when installing the Brake Controller 7 & 4 Way Installation Kit, item # ETBC7, and a brake controller on vehicles that do not have an existing 7-way connector... view full answer...
To tell if your vehicle has LED lights or incandescent lights, you really need to look at the light bulb itself as the outside lenses can be deceiving. Incandescent lights have a bulb with a filament like # VX-SDH11 where you see the wires making a connection on the inside. An LED light has what looks like a computer chip with a diode or many diodes that are circular like # DI85VR. view full answer...
A 5/8" diameter hitch pin is usually made of steel, though some have coatings applied to help resist corrosion.
For example, the Master Lock Pivot Lock Hitch Pin for 2" Hitches # ML1465DAT is made of stainless steel, but there is also a version - the Master Lock Pivot Lock Hitch Pin for 2" Hitches # ML1495DAT - which is a chrome-plated steel hitch pin with a chrome-plated aluminum barrel. view full answer...
Each of our 10 Inch lube plates for fifth wheel hitches are made from nylon, which is going to just as good a job as the graphite lube plates so you don't have to use any grease. The 10 inch lube plates we offer are:
- Curt 10" Fifth Wheel Trailer Hitch Lube Plate # 16721
- Lube Plate for Reese 5th Wheel Trailer Hitches - 10" Diameter # RP83002
I have added links to video reviews of each of these lube plates for you to check out. view full answer...
The Firestone air compressors such as # F9377 can handle typical moisture like what might splash up from the road when driving in the rain. But it is not designed to be submerged under water. For something to be waterproof it has to be able to be submerged under water for a certain amount of time and not let any water in.
It will be perfectly fine under your truck so long as you aren't planning on driving into any deep bodies of water! That is why Firestone makes a mount bracket, # F2530,... view full answer...
The Yakima HoldUp 4 Bike Rack - Platform Style - Tilting - 2" Hitches # Y02443-2 has a weight of 98 lbs without bikes on it. The two parts weigh 49 lbs each so you can use the HoldUp2 bike alone at that weight or add the additional 2 bikes at 49 lbs additional carrier weight.
When combined the rack has a total weight capacity of 200 lbs total with an individual bike weight maximum of 60 lbs.
With all the packaging the shipping weight is 114 lbs. view full answer...
I believe you are talking about the weather seals that come with TruXedo Tonneau cover # TX246601. Unless they are damaged or the truck is in extereme weather conditions frequently they can last as long as the cover does. Should you need to replace them for any reason there is a 4-pack available, # TX1703568.
The warranty would cover them if they were defective but it is a part that can wear out. the warranty specifically states:
"TruXedo, Inc. warrants that all new, unused products... view full answer...
The Integrated OEM Tailgate Lock, # LH-007, is designed to be an exact replacement to the factory handle. The locking mechanism is made of zinc coated steel, similar to the plating on heavy duty Grade 8 nuts and bolts. The handle is the same plastic that the vehicle manufacturer uses. view full answer...
The zippers on the AO Coolers Saddlebag Coolers for Bikes # AC43FR aren't waterproof so you'll need to make sure whatever you're transporting is safe from water damage. view full answer...
All of the pins on the Power Grip RV Power Cord Adapter # CAM55185 will be active. There isn't a single pin that is used with this adapter. view full answer...
I may have a solution for you if you're looking for a Pintle mount that is Made in the USA, but the Buyers Products 2" Pintle Hook Mount - 1 Position - 9" Shank # 337PM84 is manufactured overseas. However, B&W makes all of their products in the USA so you may want to have a look at the B&W Pintle Hook Mounting Plate for 2" Hitches - 9" Shank - 6 Hole - 16,000 lbs # BWPMHD14001, which is similar to the # 337PM84.
I've also linked our entire selection of B&W Pintle hook mounts that you... view full answer...
Yes, the Brophy trailer hitch ball # CB26C is made in the USA. Brophy has several options that are made in the USA. And they also have some that are not. But this one is. view full answer...
The Rightline Gear SUV Tent # RL110907 is designed with the door on the driver's side so that the driver's seat of the vehicle can be accessed easier. It allows you to get cargo out of your vehicle and then park your vehicle elsewhere so that it becomes a standalone tent (if that is the desire).
We have other tent options but they are meant to be in the back of a pickup or do not have a floor and are considered to be more of a shetler than a tent. Since you wouldn't have a trailer hooked... view full answer...
The # 337PM25812 pintle mount is manufactured in the USA, according to Buyers Products.
If you click the provided link, you can see a product description video featuring the # 337PM25812 pintle mount. view full answer...
The Draw-Tite Max-Frame Trailer Hitch Receiver # 75101 you were looking at is designed in the USA but produced in Mexico.
If you are wanting a trailer hitch receiver made in the USA I have a few options.
I recommend the B&W Heavy-Duty Trailer Hitch Receiver # BWHDRH25132 as it is the only USA made trailer hitch receiver for your 2000 Dodge Ram Pickup that does not require drilling and will fit both long and short bed models with the standard or step rear bumper.
If you are ok with an... view full answer...
Go To Results