The only parts list for your triple step is attached. It unfortunately does not give the breakdown to the extent you are seeking with Teflon plate and wave washer as those parts are not replacement options from the manufacturer. I've attached the best parts list from the manufacturer I can get as an attempt to help. If your parts are worn then I recommend getting the replacement kit # LC379804 because not all the parts you are seeking are replacement options. view full answer...
For your 2004 Itasca Suncruiser, with an Atwood RV Water Heater w/ Heat Exchange AT94023, which is no longer available, I recommend going with the Dometic RV Water Heater # DMC74FR.
This tank is a bit smaller at 6 gallons, versus AT94023 10 gallon capacity, but will also produce up to 12 gallons of hot water per hour, which should be plenty.
Additionally, this unit has an aluminum clad tank, that does a great job preventing corrosion, and also has a high-temperature limit switch, which... view full answer...
Hey Mike,
I'll go ahead and list out the highest-rated front and rear SumoSprings for your 2006 Workhorse W22 chassis (which fit so long as it is 2-wheel drive):
- Rear: SumoSprings Maxim Custom Helper Springs - 7,000 lbs # SSR-280-54-1
- Front: SumoSprings Solo Custom Helper Springs - 1,500 lbs # SSF-280-47
You made a smart choice going with SumoSprings because they do a superb job of stabilizing your rig if it starts to rock from heavy winds, or when taking a tight turn. So they'll... view full answer...
For front air bags that fit inside of the coil springs on your 2002 Workhorse P32 chassis you will need # AL81560. You can roll up these bags and insert them up from the bottom through the hole below the coil spring mounts that you have described. No need to remove the springs for installation!
I have included a helpful link to other stability products for your particular RV chassis as well. view full answer...
The screen door slide you selected, Valterra # A77022, and all other options are shown on the linked page. In the specific size of this slide, 11-11/16 x 11-7/8-inches, all items are from Valterra and will have the same thickness dimension.
Lippert 12 x 12 Bubble Slider Panel part # LC234101 is fairly close to the size of the Valterra slides but it is a bit thicker at 1-3/16-inches.
Because these are general-application replacement parts their fit may not be exact to the original and... view full answer...
Hey Lynn, you can add the Roadmaster TruTrac Front-Axle Trac Rod for Large Trucks and RVs # RM-TRACW-22 you were looking at. It's compatible with your 2004 Workhorse Chassis that has the Roadmaster sway bar on the front. There is a kit with everything combined here: # RM-1259-106, but since you already have the sway bar you can just add that trac rod.
What kind of RV is it? I know some Newmars were built on that. view full answer...
Hey Tim,
Welcome back!
For front air bags for your 2001 Workhorse P32, we have the Air Lift 1000 Helper Springs part # AL81560. The Air Lift kit # AL81560 will fit inside your Workhorse's front coil spring without any drilling or complicated modifications necessary. All the hardware, tubing, and valves to inflate the air bags are also included in this kit. Just make sure the valve is mounted in an easy to reach spot like the bumper for inflating the bags. The air bags offer up to 1,000lbs... view full answer...
Hey Philip! The Replacement Toilet Bowl Seal Kit for Dometic 200 and 500 Series RV Toilets # DOM53FR will work on your 511+S. This comes with the rubber flush ball seal and rubber bowl seal. view full answer...
Hey Donna, you would have to replace the entire setup as there was a refrigerant law change in January of 2025 that forced the complete systems to have to be redesigned and because of that nothing is currently backwards compatible. So what I would recommend is a Furrion Chill Variable Speed part # FR97TQ which comes with everything needed to install from the thermostat do the lower air box. This is widely considered the quietest, most cold, and lowest power drawing RV AC unit out there... view full answer...
Hey Claude! The SumoSprings are not the same for the front and rear axle. Sometimes they are only available for the front and not for the rear due to the design of the vehicle/chassis. Do you know what model that Workhorse chassis is?
I wasn't able to find any specific information on the Workhorse models, only those with the Roadmaster chassis. If it is a W20, W22, or W24 you can use the SumoSprings Maxim Custom Helper Springs - Rear Axle # SSR-280-54-1. If you have something else please... view full answer...
Hey Ron, thanks for reaching out!
What is the flange to flange width of your bedroom topper? If you can get me that measurement I'll be able to recommend the correct slide-topper for you.
Attached is a photo showing where to measure. view full answer...
I reached out to the manufacturer who told me the Kwikee Series 25 Steps # LC365837 you are looking to replace your older steps with will not work. This is what they told me:
"Per my parts department, based on the information you have provided, they can verify that the customer is replacing a Series 23 Kwikee step assembly with a series 25 Kwikee step assembly. He needs to be advised not to do this, as they will not fit or bolt up properly. The frame sizes are different from one another... view full answer...
I do have suspension enhancement options for a 2002 Workhorse P42 Chassis but there are no air bags available unfortunately. Instead, you can use the Timbren Rear Suspension Enhancement System. The correct one will be based off the suspension. The part # TGMRP30MH is for models with bump stop over u-bolt pad and part # TGMRP30 is for models with bump stop on the frame. These options all work well to provide additional support. view full answer...
We have the Replacement Wheel Master Lug Nut Cover for Wheel Liner part # WMRMT9061 available. These are designed to go over the keeper nuts to give you a nice clean look.
We also offer a 33mm part # WM9005-6, 7/8" Covers part # WM8019, 1" Covers part # WM8010 or the 1-1/16" Covers part # WM8011. view full answer...
Thanks for all the details Mike, that helped a lot.
For what you’re wanting to do, I’d recommend the Furrion Chill Cube 18,000 BTU ductless setup, # FR59TD in white or # FR27TD in black.
Since you’re adding a separate rear bedroom AC and won’t need the front unit to feed the whole coach, the ductless setup makes the most sense. It will give you stronger airflow in the front living area instead of losing air through older roof ducting.
Yes, it can be installed in a coach that originally... view full answer...
Hey Donald, so we do have a solution, but due to your 903206000 Kwikee Series 32 steps being made in 2003, there isn't a standalone gearbox and motor available, as Lippert (which is Kwikee) changed all the parts after 2006. That means you'll need an upgrade kit which is a new motor, gearbox, and control unit in order to work, and the correct part is the Motor Upgrade Kit for Kwikee Electric RV Steps # LC29VR. view full answer...
Hey Brad, thanks for reaching out!
The Air Lift WirelessAIR Compressor System # AL74000 is a dual path compressor which means it can control up to 2 air bags (or 2 sets of air bags). You might be able to find a specialty air compressor kit out there, but all of the options that I've heard of are either single path or dual path; I have yet to come across one that controls 4 air bags independently. This means you'll need 2 of the compressor kits in order to operate 4 bags individually.
What's... view full answer...
Hi Mike!
I assume yours is an older one? The new Kar Kaddy SS comes with disc brakes, which is why I ask.
Anyway, the etrailer Hydraulic Trailer Brake - Uni-Servo - 10" - Right Hand - 3,500 lbs # AKUBRK-35R (and left hand # AKUBRK-35L) follows the standard 4-bolt mounting pattern (see attached picture), which may work with your Demco Kar Kaddy SS. But, I couldn't find the bolt pattern for it listed anywhere, so I would definitely measure this to make sure.
If you get an odd measurement... view full answer...
Hey Doug, thanks for the information! For the front end of your 2004 Holiday Rambler, I recommend the Roadmaster Front Anti-Sway Bar and Bushing Kit item # RM-1109-116. This anti-sway bar will help with side to side movement, driver fatigue, and body roll. This sway bar fits if your Workhorse has a coil spring independent suspension and you do not have the widebody style. If you have the widetrack you'll need item # RM-1109-200.
For the rear end, I recommend the Air Lift LoadLifter 5000... view full answer...
Go To Results