We do have the replacement straps you asked about for the Yakima WindShield fairing, with the correct part being the following:
- Replacement Attachment Straps for Yakima WindShield Fairing # Y83XR
This will give you the four replacement straps you are looking for; the # Y83XR is just our part number and it is the exact Yakima part 8880587 you are wanting. view full answer...
Running board brackets are step model and manufacturer specific. If you let me know what running boards you have, I can see if replacements are available. For example the Replacement Mounting Hardware Kit for Westin PRO TRAXX 4" Nerf Bars - Manufactured After 2017 # 21-2408PK are the correct fit for the # 21-24085 confirmed to fit a 2020 Ram 1500 Crew Cab. view full answer...
The Furrion Chill FACR14SA-BL does already come with a start capacitor built-in. So you would not want to add the SoftStartRV Soft Start for Single Zone Air Conditioner Setup # SSR54FR.
If the start capacitor on your Furrion Chill FACR14SA-BL has gone bad, we do carry the replacement start capacitor.
- Replacement Start Capacitor for Furrion 14,500 Btu RV Air Conditioners # FR45FR. view full answer...
If you can send me a picture of the pigtail you're trying to replace or the inlet on your regulator I can confirm this, but it sounds like you need a pigtail with an NPT fitting as opposed to the Male Inverted Flare. The NPT pigtail which matches the one you previously purchased is # 100473-24-MBS . view full answer...
You measured correctly and the Velcro strip you need for your short bed Ram's Lo Pro QT cover is part # TX1115174 which is 1-5/16-inches wide. view full answer...
I confirmed with Extang that you have two options depending on what type of body style you have for your 2019 RAM 1500 6-1/2 foot bed. If you have the classic body, you will need the Replacement Tarp for Extang Tuff Tonno Soft Roll-Up Tonneau Cover # EX13430. If you have the newer body, you will need to order it directly from Extang with part # 13422. Extang only makes replacement tarps for 2019 Ram 1500 beds without the RAM box. view full answer...
I do have options for you but trailer coupler repair kits are not exactly universal. If I knew the exact trailer coupler you have on your trailer then I could confirm 100% whether or not we have a trailer coupler repair kit for you. However, it looks like you have the Fulton A-Frame Coupler part # F44305R0317 which means the Repair Kit for Fulton A-Frame Coupler 2-5/16" Ball part # F640801 would be correct for you.
My advice would be to order both the coupler and coupler repair kit. If... view full answer...
Without knowing what cover you have, I can not say for sure that the Replacement Lock Assembly with Keys for RetraxPRO Tonneau Covers # RTX25QR will fit your Retrax tonneau cover, on your 2017 Ram 1500.
If you look underneath of the cover right next to the lock mechanism on the driver's side, you should find a serial number. If you are able to provide the serial number, I can confirm if this is the correct replacement locking mechanism. view full answer...
Yes, the 2-Wire RV Propane Gas and Carbon Monoxide Detector, # RS54FR has two different mounting brackets to select from allowing coverage of the existing hole from previous installs. Please note the attached product review video. view full answer...
Your Dexter 8-283 brake drum will use a # 10-42 grease seal. If you are looking to replace all the races, bearings and seals you will want the following components per hub.
Inner Bearing # LM67048
Inner Race # LM67010
Outer Bearing # L44649
Outer Race # L44610
Grease Seal # 10-42
We do have the following tools to make the replacement easier.
Seal Puller # PTW1219
Install Kit # PTW83020
Bearing Packer # PTW1218
Grease # L11390
Grease Gun # L30416 view full answer...
I do know the L looking key that you stick in the square hole of the B&W Turnoverball Underbed Gooseneck Trailer Hitch # BWGNRK1309, as that is the latch pin handle.
The replacement you need is the Replacement Latch Pin Handle for B&W Turnoverball Underbed Gooseneck Trailer Hitch # BW0909-2-2002PL. view full answer...
I contacted the manufacturer about the correct replacement pads for your Aries Oval Nerf Bars - 4" Wide # AAS225041. They said that the correct pads would be one of two options. Either the Replacement Step Pad for Aries 4" Wide Oval Nerf Bars # AA2090133 or the Replacement Step Pad for Aries 4" Wide Oval Nerf Bars # AA2090161.
They also said that the pads are basically the same other than the size of the pins that go into the bar.
The # AA2090161 has smaller pins. There is a raised oval... view full answer...
The correct replacement bushing for your Dexter E-Z Flex equalizers is part # D014-077-00. This comes as a quantity of 1 but you can get a 4 pack as part # K71-291-00. view full answer...
We do have replacement arms available for your Roadmaster EZ5 Base Plate Kit # RM-521569-5 with part # RM-ARMS.
When the original base plate brackets and arms are manufactured, they are made as one single part. So to be sure that the replacement arms fit perfectly, Roadmaster just needs a bit more information regarding your original base plate brackets. Prior to ordering, you will just click on the Installation Details at the bottom of the product page and fill out the bracket order form.... view full answer...
I spoke with Retrax and you can indeed replace the rails on your RetraxPRO MX Hard Tonneau Cover # RT80232 with something that has the T slots. As you have a 2012 Ram 1500 with the 6-1/2 foot bed and no RamBox, you will need the Replacement Side Rails # RTX59FR. This is technically for a Retrax XR Series cover, but the rails will work on your MX as well. This will include both left and rights side rails and both will have the needed T slots. view full answer...
The standard angle for an A-frame trailer tongue is 50 degrees. More than likely your trailer follows the standard. Since you are unsure, you could measure it using a tool like a protractor. The Demco Cast Head Coupler # DM37ZR you looked at fits the standard A-frame and would be a great replacement choice. view full answer...
The Replacement Rubber Block for TracRac Base Rail Installation # TARB-11032-1 won't have a problem maintaining its integrity/shape as you remove and re-install the ladder rack as needed on your truck. Just make sure all your hardware is tightened down appropriately when installing everything each time.
I have attached a short video review on this component that you can check out as well. view full answer...
DeeZee Tailgate Assist Custom Tailgate-Lowering System # DZ43301 does have what they call a nut zerk fitting like what you show in your picture. If you just need to replace that part use # BKT43301. You have to be very careful not to over tighten this fitting otherwise it will get stripped out and you would need another one. view full answer...
Yes, the item listed for 3,500-lb axle, # RG06-050, should be what you are looking for. This should cover axels from 3,500 to 5,000 lb. as long as it has 12" hub, Double Lip - ID 1.719" / OD 2.565".
I have attached a few links for tool suggestions if you are in need of something to assist with this task, bearing packer, Seal puller, etc. view full answer...
We have a couple of possibilities for brackets that will work, but you do have to know the exact manufacturer and model of your Ram's nerf bars in order to get the correct brackets. The 5" oval nerf bars that fit your 2018 Ram 1500 Crew Cab are manufactured by Westin, and I'll list the name of the bars, their part numbers, and the replacement hardware for you.
- Westin PRO TRAXX Oval Nerf Bars - 5" - Polished Stainless Steel # 21-53560 or Black Powder Coated Steel # 21-53565 use Replacement... view full answer...
Go To Results