I went out to the warehouse and measured the Draw-Tite Front Mount Trailer Hitch Receiver part # 65053 for you. The bolt holes are 38" apart left to right on center and 5" apart front to back on center. I have also attached a photo with these measurements for you as well. view full answer...
The Yakima Replacement Hitch Bolt and Clip for Yakima HoldUp Hitch Mounted Bike Carrier, part # Y8890200, is a 5/8 inch bolt. The size wrench you would use to install or remove this bolt is 15/16 inch. view full answer...
I would be happy to help!
The Draw-Tite Trailer Hitch Receiver # 41906 you were looking at measures 18-1/2" from the center of the rear mounting holes to the center of the hitch pin hole where the Curt Trailer Hitch Receiver # 14055 measures 16-3/4" as you can see in the included diagrams.
Since you were needing the max distance for your 2007 Ford E-350 with the Service Bed you will want to go with the # 41906.
I included videos of the products mentioned for you to take a look at. view full answer...
The MaxxAir Mini Deluxe Trailer Roof Vent part # MA00-03851 once installed will sit almost flush with the ceiling. The panel which houses the light and control knob I would say is around 1/4" - 1/2" thick so that is all that would sit inside the trailer. I have attached a photo for reference. view full answer...
The Ultra-Fab Rotating Hitch-Mounted Skid Wheels # UF48-979014, once bolted on the hitch tube on your Class C RV, will extend down from the bottom of the hitch tube by 6-inches. This includes the thickness of the bottom mounting plate all the way down to the bottom edge of the wheel itself. You can see this illustrated in the linked photo that I prepared for you. This kit is also shown in the linked video.
All of our RV skid wheels are shown on the linked page. These include weld-on and... view full answer...
The Draw-Tite bracket for 7-way # 18138 will mount at a right angle with pre-drilled mounting holes. The hole diameter, which will fit the majority of 7-way connectors, is 2-1/16 inches.
I went to our warehouse to get this part and provide you the measurement of the mounting hole bolt pattern and several other measurements.
Take a look at the diagram I made for you. view full answer...
The Buyers Products 2" Multi-Fit Hitch Receiver For Ford/GM with Cutaway Service Bodies # 3371801401 is 21.2" Deep. The height measurement you saw of 9" is from the top of the mounting bracket to the top of the receiver. The overall height is 13.8" and the overall width is 50.4". view full answer...
I spoke with my contact at DeeZee about the Specialty Series Truck Bed Transfer Tank, # DZ91750SB. She stated that the drain plug is 1-1/2 inches and that the cap and vent can be switched. She was also fairly certain that the drain plug would not work as a gravity feed. I have included a link to the installation details for reference. This tank should not be used to carry flammable liquid such as gasoline and it should not be used as an addition to a vehicles fuel system. view full answer...
I spoke with my contact at Yakima and he informed me that this Yakima Holdup 2 Bike Rack # Y02443 will fit bikes with wheel bases of up to 48 inches. What that means is that the distance between where the tires of the bike touch the ground cannot be larger than 48 inches.
Most likely this rack will work on your bike, but you will want to determine the wheelbase of the bike before ordering to be sure.
I attached installation instructions for this product for you to check out also.
If... view full answer...
I spoke with my contact at Curt and I got the measurements between the bolt holes for you. I made a picture that shows the following dimensions:
Side to side on center the holes are 40 inches apart.
From the hole closes to the receiver to the next hole it is 3-3/4 inches. From the second hole to the first rear most hole it is 11-1/4 inches. And the two rear most holes are 1 inch apart.
This hitch is designed to fit Chevy and GMC full size vans.
I have included a link to the installation... view full answer...
The Rhino-Rack heavy duty crossbars # RB1800. The bottom part of the opening is 1.36 inches wide. The top of the opening is 0.86 inches wide. And the overall height of the channel is 0.87 inches tall. view full answer...
We can help you sort out trailer wheel bolt patterns and tire load ranges for your 26-foot travel trailer that weighs between 5200- and 6200-lbs. I linked our main page for trailer wheels and tires as well as a couple of related articles that you'll find helpful. The wheel/tire page has filters you can click on to sort the displayed products.
There are many trailer wheel bolt patterns (we offer wheels in more than 10-wheel bolt patterns!) but it is easy to confirm which you have. Just... view full answer...
The clamp-on mounting brackets for the Rhino-Rack Ski and Snowboard Carrier # RR574 are in a fixed position (this will be the case with any other ski carrier as well), but I did go out to our warehouse to measure their spacing. From the outside of the brackets there is a length of 21-5/8" and from inside to inside this length is 19-1/4".
I have attached an image to assist. view full answer...
This hitch measures 38 inches from bolt hole center to bolt hole center on all of the holes except for the rear most set of holes. These are 39-1/2 inches in width.
Check out the picture I attached to see this measurement.
You may be interested in the following products to complete your towing setup:
Tow Ready Custom Fit Vehicle Wiring # 118344 (instructions attached)
Ball Mount 1 inch Rise or 2 inch Drop # C45030
Hitch Ball with 2 inch Diameter and Medium Shank # 19247
Hitch Ball with... view full answer...
The width of the mounting channel is 2-7/8 inches for the Draw-Tite Max-Frame Trailer Hitch Receiver # DT37GR. It's pretty unlikely this is going to fit, and for applications like yours, the best option is a universal hitch that you can weld on.
So long as your frame is no longer than 44 inches wide from outside to outside, a universal hitch will work, you just need to measure how far down you need the receiver to be from the bottom of the frame (the drop). Once you know that, you can... view full answer...
The mounting holes on the MaxxAir MaxxFan Trailer Roof Vent # MA00-06200K are spaced 4 inches apart on center. On the Fan-Tastic Vent Roof Vent # FV801250 the mounting holes are spaced 3-3/4 inches apart on center. With this information you will be able to tell if either hole spacing will work for you. As for the old Fan-Tastic vent models I am not aware of the hole spacing.
We recommend using silicone, # 0160297, when installing roof vents. view full answer...
I do have a solution for you but all of our other long shank ball mounts are shorter than the Curt # C45900 that you currently have.
You could use a Gen-Y shank like part # 325-GH-303 for a 5" rise/drop or part # 325-GH-304 for a 7-1/2" rise/drop along with the Gen-Y Tri-Ball Mount # 325-GH-034 which comes with 1-7/8", 2", and 2-5/16" hitch balls and has a 12" long shank.
Another option is to use a fixed ball mount with a long shank like the Brophy # EA40 with a hitch ball like the 2"... view full answer...
I have some measurements of the Roadmaster tow dolly # RM-2050-1 for you. From the front tip of the coupler back to the pivot bolt (which is about at the centerline of the axle) is 86-1/2 inches. To the front of the dolly body it is approximately 73 inches. If the distance is not enough you could always use a longer ball mount to increase the distance some.
You may also need a high/low adapter to keep the dolly level. I have linked a help article showing how to measure and a link to the... view full answer...
The distance between the horizontal mounting holes on the Curt Trailer Hitch Receiver # 14055 you were looking at are 2-3/8" and 8" as shown in the included diagram.
I included a video of the # 14055 on a 2004 Ford Van for you to take a look at. view full answer...
Go To Results