For your companion hitch the replacement pivot arms are now only available with the base which for your model 3000 is # BWRVB3500. I'm not sure what u-bolts you are referring to, so I assume it is the chains and that is part # BW1900-2-1600. If you are looking for the saddle pin, that is # BW3025-119A. view full answer...
For a 4400-lb Lippert axle the most popular grease seal is part # 58846. This is a double-lip grease seal with an inside diameter of 1.719-inches and an outside diameter of 2.565-inches. This seal is often used along with inner wheel bearing # L68149 and outer bearing # LM67048. view full answer...
The Replacement Wireless Remote for Air Lift WirelessAIR Compressor System # AL73002 is designed to work with the Air Lift WirelessAIR compressor system AL72000 and is the only remote compatible with that system.
To use a different remote you would need to change your compressor system to one like the upgraded Air Lift WirelessAIR Compressor System for Air Helper Springs # AL74000EZ which can be controlled by included remote, or by your smartphone via Bluetooth.
I included a video of... view full answer...
You can change your ST205/75/D15 trailer tires to a larger ST225/75/R15 size IF your 15-inch rims are either 6-inches or 6-1/2-inches wide AND IF you have sufficient clearance around the tires for the increased width and overall diameter of the ST225/75/R15.
A 205/75-15 tire when mounted and inflated has an overall diameter of about 27-inches. A tire in size ST225/75/R15 has an overall diameter of 28.4-inches, about an inch-and-a-half larger. The larger tire will also be about 3/4-inch... view full answer...
I have the Draw-Tite Signature Series Replacement Indicator Flag Kit, part # 58216. This is the indicator flag assembly that fits the Draw-Tite, Reese, and Hidden Hitch Fifth Wheels. It attaches to the fifth wheel head assembly and will indicate if the trailer is properly connected to the fifth wheel hitch. If the trailer is not properly connected this flag assembly will keep you from inserting the bail pin into the handle and base plate of the fifth wheel.
I also have the Reese Signature... view full answer...
Based on my research, the Glo-Brite 118A amber light is approximately 4 inches long by 1-1/2 inches wide. I spoke with my contact at Optronicc who confirmed that their Replacement Amber Lens # A44AB will fit the Glo-Brite 118A trailer light.
I found the Glo-Brite 117R light to be a red taillight of the same 4 inches by 1-1/2 inches. For a replacement lens for the red light you could use part # A44RB. view full answer...
As long as the corresponding socket located behind the bumper is still intact, the Tow Ready # 20135 will replace the damaged 7-way trailer connector.
You can use a circuit tester like part # PTW2993 to test the existing connector to ensure it is still functional.
This is done by activating the lighting circuits (headlight, taillight and turn signal) and testing the pins and making sure they light the tester.
I have linked you to a video showing how the tester is used. view full answer...
We do have some options available that are a bit longer than the Bulldog BX1 Gooseneck Coupler Inner Tube # BD1289050300.
The Bulldog BX1 Gooseneck Coupler Inner Tube # BD1289020300 has the same diameter and hitch ball spec and it has an overall length of 28.5" which is 6.5" more than the part you were looking at. The only problem is that it is only rated for 25,000 lbs.
If you are needing the 30,000-lb weight capacity rating then you can go with the Convert-A-Ball Multi-Cushioned Gooseneck... view full answer...
By hitch I assume you mean the shank. I would need to know the model number of the weight distribution system to get you the correct replacement arms. If you could get back to me with that information I may be able to find a solution for you. view full answer...
The spindles can be replaced. However, they will need to be welded by a certified welder. They use special jigs so that it is concentric and square on the axle or it can cause problems with uneven tire wear and wheel tracking.
I've linked our selection of spindles for your to find the correct part for your trailer. view full answer...
The Tru Ryde grease seals you mentioned, part # RG06-70 are indeed a replacement for the 10-036-00 Dexter seals. They would work great for your application. view full answer...
The Replacement Front Roller Bolt for Titan Model 10 Brake Actuator # T0828800 takes the Hex Nut for Titan Model 10 Brake Actuator - 1/2"-13NC # T0798500. To go with the bolt and nut you can also use the Replacement Lock Washer for Titan Model 10 Brake Actuator - 1/2" # T0793700.
Each of these parts are available through us; you can simply scroll down a bit and click on the "Add to Cart" button for each product and you'd be all set. view full answer...
In order to recommend the correct Trailair replacement pin box for your Keystone Challenge 5th wheel, I will need to know the manufacturer and model number of your OE pin box. This information should be listed on a plate or sticker affixed to the pin box. If you would care to reply with this information, I would be happy to make a recommendation.
If you cannot find a model number or manufacturer, you can take some measurements of your OE pin box as shown in the FAQ article I have linked... view full answer...
From the picture that you sent in it looks like you have the Hide-A-Goose part # 9460, # 9464 or # 9465. If the vehicle you are installing this on is the 2003 Dodge Ram Pickup that you inserted for your vehicle information then the part # 9464 is the correct option for your application. For a 1500 the whole gooseneck hitch would be part # 9464-38 while for a 2500/3500 the kit would be # 9464-35.
The 9464 part number comes with the plate and the hitch ball. Unfortunately the plate is not... view full answer...
Replacement parts for an Atwood actuator are going to be very hard to find these days. Atwood stopped producing actuators quite a while back, so at this point unless you can find parts secondhand, replacing the actuator is going to be your best bet.
To replace the Atwood actuator the Demco # DM72VR for drum brakes or # DM62VR for disc brakes will work really well. These have a 7,000 pound towing weight capacity, a trigger-style latch that's easy to use for a secure connection with the... view full answer...
Your Kendon fold-up trailer has a 2K axle, given the 1.063 diameter spindle you referenced.
Assuming you have idler hubs, you'd need # 8-91-05UC1-EZ for a 4 on 4 bolt pattern or # AKIHUB-545-2-LF-2K for a 5 on 4-1/2 inch bolt pattern. The L44649 inner/outer bearings, L44610 races, 10-9 grease seal, dust caps for standard or EZ lube spindles and lug nuts are included. The hubs are pre-packed with grease and are 100% ready for installation.
If you were just needing the bearing/race/seal... view full answer...
Thanks so much for the photo, which shows you have a UFP A-60 actuator, which is the same as the Dexter DX7.5L A-60 Brake Actuator - Drum # DX33FR.
I can confirm that the correct replacement inner member for both actuators is the Replacement Inner Member # DX97FR. view full answer...
That part is a Replacement Rubber Block for Base Rail Installation of TracRac Sliding Ladder Racks - Qty 1, part # TARB-11032-1. I have included a video demo link below. view full answer...
It sounds like you have a Leland 7920 pin box. This matches all of the specs you gave except the 2b measurement which is the height different between one set of bolt holes to the row that is either one set higher or one set lower. The Leland 7920 has a 1-1/2" 2b measurement. If you were measuring from where your bolts are installed and there is a row in-between them then that would explain the difference.
We do carry a variety of upgrades for your pin box but none of them are the OEM version.... view full answer...
Go To Results