Replacement Front Roller Bolt, Hex Nut and Lock Washer for Titan Model 10 Brake Actuator
Published 06/02/2018
Products Featured in This Question
Question:
Thanks for answer!! Was pressed for time so I ordered them assuming I could find the nuts. I was also curious if you could tell me the nut required for the T0829400? Thanks again!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
asked by: Alan
Helpful Expert Reply:
The Replacement Front Roller Bolt for Titan Model 10 Brake Actuator # T0828800 takes the Hex Nut for Titan Model 10 Brake Actuator - 1/2"-13NC # T0798500. To go with the bolt and nut you can also use the Replacement Lock Washer for Titan Model 10 Brake Actuator - 1/2" # T0793700.
Each of these parts are available through us; you can simply scroll down a bit and click on the "Add to Cart" button for each product and you'd be all set.
Product Page this Question was Asked From
Replacement Front Roller Bolt for Dexter Model 10 Brake Actuator
- Accessories and Parts
- Brake Actuator
- Disc Brakes
- Hydraulic Drum Brakes
- Rollers
- Bolts
- Dexter
more information >
Continue Researching
- Search Results: kodiak 225 caliper
- Shop: Replacement Bolt for Dexter Model 20 Brake Actuator - 4-1/4" x 5/8" NC - Grade 5
- Shop: Kodiak Disc Brake Kit - 10" Rotor - 5 on 4-1/2 - Dacromet - 3,500 lbs
- Shop: Replacement Master Cylinder Assembly for Dexter Model 60 Brake Actuators - Disc
- Shop: Replacement Strut for Dexter Model 60 Brake Actuator
- Shop: Replacement Roller for Dexter Model 60 Actuators
- Shop: Kodiak Disc Brake Kit - 10" Rotor - 5 on 4-1/2 - Dacromet and KodaGuard - 3,500 lbs
- Video: What to Know About the Replacement Push Rod Assembly for Dexter Model 60 Brake Actuator
- Shop: Replacement Shock for Dexter Model 6 and 10 Brake Actuators
- Video: Review of the Dexter Brake Actuator
- Q&A: Where Do the Rubber Bearings Go On the Titan/Dico Model 10 Surge Brake Actuator
- Q&A: How to Loosen Hardware Securing Master Cylinder in Titan Brake Actuator
- Search Results: dx20ex
- Q&A: Diagram for Replacing Titan Model 10 Actuator Shocks
- Video: Replacement Master Cylinder and Push Rod Assembly for Drum Brakes Spec Review
- Shop: Trailer Hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Trailer Wiring Diagrams
- Search Results: trailer hitch
- Shop: Trailer Wiring
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer leaf springs
- Shop: Suspension Enhancement
- Q&A: Does etrailer Carry Furrion Chill Cube w/ Heat Pump to Replace Dometic Duo-Therm
- Article: How to Measure for Trailer Hitch Drop
- Search Results: spare tire mount
- Shop: Brake Controller
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: How to Measure Your Trailer Wheel Bolt Pattern
on Accessories and Parts
Alan
6/2/2018
Thanks for answer!! Was pressed for time so I ordered them assuming I could find the nuts. I was also curious if you could tell me the nut required for the T0829400? Thanks again!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!