2" Round. Waterproof trailer light serves as either a side marker light or a clearance light. Red lens with reflex reflector. Recessed mount with built-in flange. 2-Wire pigtail. 7 Diodes. P2 rated.
Features:
Specs:
The waterproof construction of this light makes it ideal for use on trailers that may be submerged, like a boat trailer. The housing and lens are sonically sealed together to create a single unit, which means that water will not get into the light and damage the diodes or circuit board.
A P2-rated or P3-rated light produces a 45-degree angle of light to either side of its centerline for a total of 90 degrees of coverage. This beam pattern can be seen straight on, but it cannot be seen clearly from the side. So this type of light can be used as either a side marker light or a clearance light, but it cannot function as both. If you need both functions, then you must install 2 separate lights on your trailer - one as a front or rear clearance light and one as a side marker light.
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today, we're going to be taking a look at part number MCL52RHXB, this is the optronics LED clearance or side marker light. It's going to have a built-in reflex reflector, here on the mounting flange and over the main portion where the lights are. The round trailer light is going to serve as either a side marker light or clearance light. It is sonically sealed, so it's going to feature a water-proof housing and lens unit that's submersible. The LED's are going to make great replacements for incandescent lights. They're going to last a lot longer; they're going to be much more efficient, and you don't have to worry about replacing the bulbs and you don't have to worry about inaudible 00:00:38. We're going to have the red lens, again it's going to have that reflex reflector.
The lens and the housing is going to made from a poly carbonate material, it's very strong and very durable. This is a recess mount installation, it's got a built-in mounting flange, right here. And then this portion is going to be the recess portion. Can we take a measurement of that recess area real quick And that's going to give us a measurement of about two inches. Also, here at the back you're going to notice that it has a two wire design. White wire is going to be for ground, black wire is going to be for power.This is Department of Transportation compliant, and it is P-2 rated.
And it's going to come with the foam mounting gasket, it goes back there, just adds a little bit of cushion when you're ready to install it. You're mounting hardware is not included. We're going to take a few measurements real quick, starting with the diameter of just the light. That's going to measure about two inches. Overall diameter from outer edge to outer edge is going to be about three and one sixteenth of an inch. We measure the entire depth from the very back to the very front, we're look at about three quarters of an inch.
The mounting holes on the unit are going to be separated on center by two and one quarter of an inch, and that's going to be the same distance between each mounting hole. And then the diameter of the mounting hole is going to be about three sixteenths of an inch. This light's going to contain seven diodes or seven LED's. The power drawl at twelve inaudible 00:02:12 volts is 0.063 amps and optronics is going to put a life-time warranty on the LED's. We're going to go and hook it up to our extra power source, that way you can see what it looks like with power running to it. So, take our white wire and ground it and then black wire, again, is for power.
So, you can see here the light sends out a nice strong consistent signal. It's going to contain seven LED's, so it's going to optimize our light output, because of the multi-diode design. You can really see the reflex reflector taking effect there, it covers the entire lens except for right here in the center. So, we're going to have the one main LED and then we're going to have six other LED's that surround that main one. That's going to do it for today's review of part number MCL52RHXB. This is the optronics LED clearance or side marker light.
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.