Best 2012 Ford Fiesta Car Tow Bar Wirings

The wiring went together well on the car.

Very complete kit. My only problem mounting it in a 2014 Chevy Spark is the limited space for the diodes. After much trial and fitting I found a suitable location. See photo.

Click to Enlarge

Click to Enlarge

Found this item was wired with the brake lights for the brown wires and turn/running lights for colored wires and this fact kept me from getting this done very rapidly. Once identified, went together really nicely and actually grounded to frame for higher light output. I upgraded 3 wire into 2 wire converter with "Roadmaster Brite-lite 3 to 2 Wiring Converter" and they are as bright as the lights already in the housing. Except for that wiring issue, it would have been excellent. As to performance after install, great. Customer service was nice from Roadmaster as well. Did receive a call back message from etrailer a couple days later.

Very easy to install... Works great

Product recieved ok...all looks good...thkx

It does what it says on the tin. Easily lit up my XJ so I could tow it. Only regret is that by making the connections at the rear, you don’t get the front market lights on the toad. I should have connected the running lights diode in the harness under the dash so all the marker lights come on at night.

In ordering the parts I got a little confused as to exactly which kit I needed. My motorhome has combined brake/turn signal lights & the car ('03 Subaru Outback) has separate brake/turn/parking lights. Thought I needed the 6 diode kit (which I ordered) until I had all the parts here & read through the instructions for the umpteenth time (BEFORE cutting anything) & then realized what they were doing. Turns out all I needed was the 4 diode kit. Sounds like there won't be any problems returning the unneeded parts since they were never installed. Great service there! Took a lot apart in the back of the car because of the lack of space behind the tail light assemblies, but it all comes apart pretty easily. Also allowed me to route the wiring along side the stock harness. Have a bunch of 1/2" split loom here & used it. Thought I would have lots of wire left over, but I actually had to splice 2 cut offs to make a jumper long enough to get from 1 side of the car to the other. Glad the car wasn't any longer & I didn't have to make up 2 jumpers as with some of the kits! Hardest part was finding a hole in the firewall & getting the harness routed under the dash so as to not tangle with the pedals, etc. I just don't flex like I used to. Everything works fine although it was NOT a "5 minute job".

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

The diodes and wiring are good and worked well. But the 118158 converter produced a 3.5 volt drop such that the brake lights were as dim as the tail lights. And when a turn signal was triggered the brake lights dimmed even further. I ended up stringing a separate brake wire through the car and re-wiring my truck with a 5-wire connector.

Click to Enlarge

I was looking for something to add to my 2014 Equinox for tail/brake/t-signal lighting for towing behind my motorhome. This system worked perfectly , and couldn't have been easier to install. The hardest part was running the wiring from front to rear ( through frame rails and what-not ). Tail-lite hook-up was a breeze. There was plenty of wire to do the job also. Now the vehicle lites work as a trailer and does not interfere with the normal vehicle lite operation.

Click to Enlarge

installed your isolating diode wiring harness 38955 also the blue ox base plate bx1126 . install was very easy with video on your site.was installed on my 2007 wangler to be towed with holiday rambler motor home.

Click to Enlarge

Click to Enlarge

This kit did the job very well. I could have bought each part separately and saved some money, but I went with the comfort knowing all these parts will work together to accomplish the job. I couldn't figure what LED bulb to use for both brake and turn signal. I routed the wire along the truck wiring harness for half the way to the front, then slipped it into the frame channel for the rest of the way. I used a Curt heavy, round 4 pin plug at the front grill. It was a bit of work and took many hours but came out clean!

I installed this on our 2019 Equinox towed. Love the convenience of just plugging in the towed vehicle. The most difficult part was deciding on what part of the light housing to drill the hole for the light socket.

I needed to wire our ‘17 Chevrolet Sonic for towing behind our Motorhome. My local shop wanted over $xxx to install such wiring. Online I found the Blue Ox wiring kit and decided to do it myself. The kit and instructions were very complete and informative and it took me about three hours to complete the installation. The time consuming part was removing and reinstalling trim and panels to hide the wiring inside the car. The thing I like most about this kit is it’s independent of the cars wiring system and I’m very happy with it.

I put this base plate on with the assistance of my wife very easy to install. Do recommend the video to install

Click to Enlarge

This place is the best! Placed my order- easy peasy-delivered on time- Watched install video- again made it so easy and saved $1000 installation fee!!! Thanks for being a great company and special thanks to Carol C my order specialist !!!

I installed this myself along with a tow bar from another company at the same time, in about 4 hours. installation was straightforward and worked perfectly. saved about $800 in total labor.

The install on my Ford Maverick is clean and functional, so this is more of a customer service review... excellent customer service! During the 4-day towing set-up install, the forecast was for freezing temps and my rig was not winterized. I called in mid panic and the motorhome was moved indoors. A few months after using the tow set-up, a minor problem developed. I called and the CSR apologized and said, I can see how that might be frustrating, and a replacement cable (slightly longer) was sent free of charge.

Click to Enlarge

The installation ins ructions and video were very helpful. The wiring kit worked perfectly.

Took a bit to get to the rear lights on the wrx - trim pieces etc. But once there the instructions were easy to follow and the lights work great!

I returned this item in favor of the Curt Bronco flat tow light kit. The Curt kit is far superior to the Blue Ox kit. The Curt kit is totally plug and play no diodes to deal with. I would have bought the Curt kit from you if you sold it. You would be better served with the Curt kit.

These lights have worked flawlessly for the whole 2023 camping season on my RV towed vehicle. I mount them on the rear of the roof so they are nice and high above bicycles on a hitch mounted rack.

They were shipped fast and arrived quickly. These are quality lights with very strong magnets. I installed them on my Jeep in no time after making some steel brackets for the tubular aluminum bumper. Would be nice to have 5 or 6 magnetic clips to place along the wire to secure it to the vehicle. I highly recommend these lights.

Overall it worked fine. Easy to use. We did encounter some high winds that twisted the light sideways once. Magnet strength otherwise is strong enough.

A very easy way to light my jeep when towed without having to cut into the jeeps wiring system.

Bought this light kit to install in the un-used bottom position in or 2005 Honda CR-V. No need to tap into vehicle's wiring harness. Easy to install, works great! Highly recommend.

Click to Enlarge

Click to Enlarge

This bulb kit is just what I needed to add trailer lights to my 'toad' vehicle. The sockets felt like quality items, it was simple to install. I had my own wire, I think it turned out great.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

My E-trailer experience was outstanding! From the great selection guide to the delivery to the installation support. The installation videos were very helpful. I had two installation issues that were answered with a prompt phone call. One call was on a Saturday morning. I highly recommend E-trailer!

Highly recommend E-Trailer for all of your towing accessories. Great product, great customer service!!

etrailer was extremely helpful in getting me parts to flat tow our 2023 Jeep Wagoneer. More specifically, Noah took the time to research the required parts, offer technical guidance, and follow up to ensure I was taken care of. Top notch service which was much appreciated.

Needed new wiring and diodes for my 2023 Jeep Rubicon. ETrailer makes it so easy to set up all the wiring for flat towing.

The labels for the Right Taillight Running Light splice were labeled Backwards, to module and to vehicle were reversed which wasted 30 minutes of time. Beware! etrailer may want to get this right with the vendor or risk a bunch of needless returns.

I have bought off of you before everything was great this is the first time that I received something that was not what it was supposed to be or was used before the papers on the installation were all wrinkled and dirty and had writing on the ends of the wire were all cut and the connectors were not on I called your company and they made it right and gave me back my money except for my shipping and they told me just to keep it it's no good to me but thank you and I am still buying off of you

have successfully completed the installation of the following items that I purchased from etrailer: > Nighthawk RM-676 tow bar > RM-524458-5 base plate > DEMCO Stay in play DM86VR > RM-152 diode wiring kit > RM-156-25 charge wire kit > RM-88400 brake switch relay kit I work slow but methodically. I had no issues other than the high degree of difficulty for a 68 y/o man working alone. This project exceeds the abilities of someone NOT mechanically inclined. There is also the need for some specialty tools. I found that feeding the wiring through the dash, firewall, and underbody was more difficult than installing the front baseplate. Overall, I am satisfied with the function of this installation. I am glad I did it myself rather than having it done. Tow vehicle: 2021 Entegra Emblem 36U Towed vehicle: 2018 Ford Fusion Platinum Energi

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

It fits the bill--when they say universal that's correct; may not be a "factory" wiring harness but our Super Beetle is 45 yrs old.

They work great on my Class C pulling my Honda CRV.

I just received them and tested them out and they work great. They are very bright and responsive. I look forward to using them in the future when I tow my vehicle behind my RV.

Installed in my 2024 Chevy Trax. I ran the wire harness up through the front fender, and along the DS rocker panel. No drilling into body required. However, I purchased extra loom to better protect exposed wires next to body. Additionally, I purchased extra wire to support the DS to PS taillight connections. Finally, be advised the plastic taillight assemply is "double hulled," so once you bore through the exterior of the assembly, you will need to drill again, into the lense. On this point, and to ensure a good fit of the bulb socket, a Dremel tool was used to grind down the plastic surface, to ensure a good flat and tight fit. Finally, I used the first cut-out to fashion a cap and to seal the light socket installation. See pic.

Click to Enlarge

I am very happy with this kit. It gives you everything you need to setup an independent brake light system for you toad and therefore bypassing the vehicles internal wiring and computers. I went with this setup as I did not want to complicate my wiring or damage the internal systems of the toad. IT takes sometime to install, but once done hooking up and running the system is simple as plugging in your 7way connector. Combine this with a onboard braking system, and you have the perfect system to pull your two vehicle behind your RV.

Poor quality trailer light connector/transmitter. I received two different ones both with already broken transmitters. The first one was the wrong part anyway.

Click to Enlarge

Haven't had time to really use it, but I connected it and all lights appear to be working as designed. This saved me a lot of time. Rather than having to run wiring through my truck and modify the taillights, this will do just fine! Hope it holds up and glad it's made in the USA.