# 1
Roadmaster Tail Light Wiring Kit with Bulbs
Found this item was wired with the brake lights for the brown wires and turn/running lights for colored wires and this fact kept me from getting this done very rapidly. Once identified, went together really nicely and actually grounded to frame for higher light output. I upgraded 3 wire into 2 wire converter with "Roadmaster Brite-lite 3 to 2 Wiring Converter" and they are as bright as the lights already in the housing. Except for that wiring issue, it would have been excellent. As to performance after install, great. Customer service was nice from Roadmaster as well. Did receive a call back message from etrailer a couple days later.
Very easy to install... Works great
# 2
Roadmaster Tail Light Wiring Kit for Towed Vehicles - LED Bulb and Socket - Red
This kit did the job very well. I could have bought each part separately and saved some money, but I went with the comfort knowing all these parts will work together to accomplish the job. I couldn't figure what LED bulb to use for both brake and turn signal. I routed the wire along the truck wiring harness for half the way to the front, then slipped it into the frame channel for the rest of the way. I used a Curt heavy, round 4 pin plug at the front grill. It was a bit of work and took many hours but came out clean!
I installed this on our 2019 Equinox towed. Love the convenience of just plugging in the towed vehicle. The most difficult part was deciding on what part of the light housing to drill the hole for the light socket.
# 3
Blue Ox Tail Light Wiring Kit - Bulb and Socket
I needed to wire our ‘17 Chevrolet Sonic for towing behind our Motorhome. My local shop wanted over $xxx to install such wiring. Online I found the Blue Ox wiring kit and decided to do it myself. The kit and instructions were very complete and informative and it took me about three hours to complete the installation. The time consuming part was removing and reinstalling trim and panels to hide the wiring inside the car. The thing I like most about this kit is it’s independent of the cars wiring system and I’m very happy with it.
I put this base plate on with the assistance of my wife very easy to install. Do recommend the video to install
# 4
Roadmaster Standard Magnetic Tow Lights
These lights have worked flawlessly for the whole 2023 camping season on my RV towed vehicle. I mount them on the rear of the roof so they are nice and high above bicycles on a hitch mounted rack.
Extremely happy with the tow bar wiring. Not one problem for the year!
# 5
Heavy Duty Magnetic Tow Lights - 20' Wiring Harness with 4-Way Flat Trailer Connector
Overall it worked fine. Easy to use. We did encounter some high winds that twisted the light sideways once. Magnet strength otherwise is strong enough.
A very easy way to light my jeep when towed without having to cut into the jeeps wiring system.
# 6
RoadMaster Bulb and Socket Set for Tail Light Wiring Kits
Bought this light kit to install in the un-used bottom position in or 2005 Honda CR-V. No need to tap into vehicle's wiring harness. Easy to install, works great! Highly recommend.
This bulb kit is just what I needed to add trailer lights to my 'toad' vehicle. The sockets felt like quality items, it was simple to install. I had my own wire, I think it turned out great.
# 7
Hopkins Magnetic Tow Lights - Red LEDs - 4-Way Flat Connector - Wireless
They work great on my Class C pulling my Honda CRV.
I just received them and tested them out and they work great. They are very bright and responsive. I look forward to using them in the future when I tow my vehicle behind my RV.
# 8
Roadmaster Tail Light Wiring Kit w/ 7-Way to 6-Wire Connector - LED Bulb and Socket - Red
Installed in my 2024 Chevy Trax. I ran the wire harness up through the front fender, and along the DS rocker panel. No drilling into body required. However, I purchased extra loom to better protect exposed wires next to body. Additionally, I purchased extra wire to support the DS to PS taillight connections. Finally, be advised the plastic taillight assemply is "double hulled," so once you bore through the exterior of the assembly, you will need to drill again, into the lense. On this point, and to ensure a good fit of the bulb socket, a Dremel tool was used to grind down the plastic surface, to ensure a good flat and tight fit. Finally, I used the first cut-out to fashion a cap and to seal the light socket installation. See pic.
I am very happy with this kit. It gives you everything you need to setup an independent brake light system for you toad and therefore bypassing the vehicles internal wiring and computers. I went with this setup as I did not want to complicate my wiring or damage the internal systems of the toad. IT takes sometime to install, but once done hooking up and running the system is simple as plugging in your 7way connector. Combine this with a onboard braking system, and you have the perfect system to pull your two vehicle behind your RV.
# 9
Custer Wireless LED Tow Bar Light - Weatherproof - Magnetic Base - 23" Long - 7-Way Round
Poor quality trailer light connector/transmitter. I received two different ones both with already broken transmitters. The first one was the wrong part anyway.
Haven't had time to really use it, but I connected it and all lights appear to be working as designed. This saved me a lot of time. Rather than having to run wiring through my truck and modify the taillights, this will do just fine! Hope it holds up and glad it's made in the USA.
# 10
Heavy Duty Magnetic Tow Light Set - Incandescent - 30' Harness
Great product, strong and reliable. Very easy to put on and take off of my tow vehicle.
This product worked great. I am very happy.
What our customers are saying:
"Excellent customer service. Best on-line ordering experience yet!"