To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
When you’re carrying tools, groceries, or gear that need to stay protected, the RetraxPRO MX delivers serious security. Its 1" thick aluminum slats are impact and weather resistant, standing up to falling debris and harsh conditions without denting or warping. The matte black finish is scratch resistant and won’t fade in the sun, keeping the cover looking sharp through rain, snow, and extended UV exposure. With weather stripping and foam seals on all sides, it keeps out moisture, dust, and road grime so your bed stays clean and dry.
Getting to your cargo shouldn’t be a chore. The RetraxPRO MX retracts smoothly along sealed ball-bearing rollers, needing no springs or lubrication to operate. You can slide it open with one hand using the pop-up locking handle, then latch it at any point along the rails to cover what you need and leave room for oversized loads. When fully retracted, it rolls into a compact canister at the bulkhead that doesn’t eat up bed space—its angled bottom even leaves extra room underneath for longer cargo.
Keeping your gear out of sight and out of reach is what this cover does best. The flush-mounted locking handle sits under a flat lid that hides the keyhole and shields it from dirt and corrosion. Once closed, the aluminum panels can’t be pried up or cut open, giving you more security than soft covers or folding designs. You can lock the cover anywhere along the rails for partial coverage or close it fully for maximum protection—then just lock your tailgate to secure everything inside.
A tonneau doesn’t have to look bulky to work hard. The RetraxPRO MX sits only 1" above the bed rails for a clean, low profile that flows with the truck’s lines while still offering clearance for most fifth-wheel hitches underneath. When extended, the top panel overlaps the bulkhead and canister for a seamless fit that reduces wind drag and helps improve fuel economy. It’s tough, sleek, and built to last without calling attention to itself.
Getting it mounted is straightforward—no drilling required. The side rails clamp directly to your bed rails, and the pre-assembled cover inside its canister goes on with simple bolt-on clamps. Two included drain tubes route through existing bed holes to channel away any water from inside the canister so it stays dry roll after roll. With a 500 lb evenly distributed weight capacity and a limited lifetime warranty, this cover is ready for daily use year after year.
Ratings & Reviews
A very nice cover. So far, it’s kept the bed and it’s contents dry. I had the face of the cartridge (the part that becomes the rear of the bed) sprayed with Line-X to match the rest of the bed and to offer some degree of protection. But the metal is very thin there and it didn’t take long for it to become dented. Also the drain fittings that attach to the bottom of the cartridge are delicate. I’ve had to order replacement fittings and it looks like the second set have broken again.
I love this cover. I had one on a different truck, but it had the rails that could be used for a bike, kayak or ladder rack. I thought I had purchased the same rails, but when received, found that it was not the same. I didn’t realize it until after I installed it. Wish I had noticed it earlier as the rails to replace are $500. Be certain you order carefully.
My third Retrax. The fit and finish is on point. Nice job... Again!
Easy installation. No problems after a year on my truck. Very satisfied with the purchase.
Only had this cover for a few weeks but it so far.
I had some damage. It was a dent in the main box. I went ahead and used it anyway. I didn’t call or ask for return because I needed the cover right away and I messed the box up which would make the return hard to do. This was not etrailers fault. It was a packing issue from Retrax.
The RetraxPRO MX Hard Tonneau Cover was very easy to assemble and install. Item was packaged very well for shipping. I would recommend this tonneau cover.
Very well built and easy to use, great product.
Vert good quality. No failures despite repeated use.
This cover looks amazing and rolls so smooth. No heavy trifold flipping. I have the 8’ bed and it works great.
On my previous truck, we had installed a soft snap-on tonneau cover. While it looked great, its performance over time decreased significantly, particularly in cold weather! So this time around, I decided to splurge and purchase a high-quality roll-top hard cover. I am SO HAPPY that I did! As importantly as its ease of installation and use, it is lockable so I will no longer have sleepless nights while traveling, worrying about the items in the truck bed. eTrailer was a great help in expediting the delivery of this item, as my HOA requires pickup trucks to have their beds covered... Thank You!
I like the old latch system better.
The wire loom for drains is not going to last long.
Great quality very happy with this. Would recommend to anyone looking for a nice retractable cover.
Item came on time and was very easy to install, but you need somebody to help you lift and put in the back of the truck as instructed. Its not that heavy, but just too awkward for one person to lift and place.
The tonneau works well. I wanted something that would be pretty secure (aluminum and locking) and easy to open/close. It is all those things! One handed open/close. Few pieces that are below the cover level so it doesn't interfere too much with what you have in the bed. Install was ok - definitely two people are easier than one.
Two downsides. The roll up area does take bed space - more than I'd like. Also, it is not watertight. Not terrible in the rain, but a good downpour or car wash gets water in the bed.
Nice product. More difficult to get the rails attached than it should have been. Very glad I had 2 strong guys helping me.
Love the results.
This was a really easy installation. 2026 GMC 3500 DRW. I did it the install myself pretty quickly (except for lifting the combined rail/cover into the truck). One person on each side to guide and lift while my daughter lifted the weight in the middle of the bed worked well. The few connection screws required fit easily. Seals at the front of the truck and on the tailgate are smooth and complete. I didn't make both sides parallel when first installed. I loosened the middle and tailgate ends of the rails, adjusted the spacing distances, and it's perfectly in align now. One person can very easily expand and contract the top. The two drain hoses won't fit the holes in the truck bed. I'll pickup something from Home Depot or Lowes to append a reducing method. I really like this bed cover!
Should put actual installation instructions with the product inadition with the on line.Something was catching when attempting to operate. Semes to work ok after it broke free.
Received my order in a timely manner. It was an easy install. I’m 65 years old and was able to install by myself.
The instructions were definitely lacking—ended up finding a decent YouTube video. The box itself wouldn’t fit between the rails on the inner sides of the bed (see pics), so I had to use prybars to seat it past the rails.
Functionality: seems very solid once installed and rollers help it slide easily either direction. I’m not convinced it’ll hold much water out, but that’s partly due to the ram box hinges next to the tonneau rails, then not a lot of pressure between the tonneau and the top edge of the tailgate. I also had a $500 tonneau in the past with weather stripping along the front box to scrape debris from the top side of the tonneau as it retracts into the box at the front of the bed. This doesn’t have that, so it seems debris will accumulate inside the box and I’m not sure how easily it will be to clean inside the box.
Time will tell if this is worth the price tag, but it does feel very sturdy once installed.
I was hesitant to try a canister type roll up bed cover after only having hard covers or a soft roll up above bed cover before. I'm glad I did...
It still gets 5 stars because even though the box for the rails was damaged, no parts were missing and there were no dents or scratches on any of the pieces.
The install was easy, did it by myself in a couple of hours not rushing to get it done but working at a leisurely pace. The only time I needed help was to position it in place after the side rails were attached. The part that took the longest was measuring and adjusting the width between rails from the front to the back to get them within spec so the cover moves smoothly and easily with no binding. The instructions were easy to follow and it is simple to put together and install. Just take your time measuring between the rails and it will glide effortlessly.
I like the size of the canister, it doesn't take up much space at the front of the bed, even though it has 8ft to roll up. It seems as if it will be pretty water repellent with the rubber seals and gaskets. It rolls up easily and doesn't retract fast and slam into the canister. It also rolls out easily all the way to the tailgate. Unlike previous covers I have had, this one doesn't require the tailgate to be closed to work properly. The cover can be extended all the way to the tailgate and you can open and close the cover or tailgate independently of one another. I also chose this particular cover because it had the anywhere lock feature rather than only a few set locking points. The matte aluminum is a nice clean look, and it seems like it will be less prone to sagging in the middle as time goes by. This particular model sits just a little above the bed (the bed cover rails sit on top of the truck bed) but the canister isn't any higher than the rails or the cover itself when its open or closed. It looks seamless and clean.
It's only been a few days since install but as of now, I couldn't be happier having chosen this bed cover. And as always, etrailer makes the ordering process easy and worry free with their vehicle specific fit, fast shipping and fair prices.
The product surpassed the manufacture d ecription
I have owned this roll top truck bed cover for a year now and still absolutely love it. I've owned other similar ones over the past twenty five years and this one is and has been the best. Sturdy, solid and so far, maintenance free. It certainly more weather (water) resistant as well. It definitely was more expensive than the other covers I've purchased in the past but the bitterness of poor quality remain forever and the higher cost of something well made are soon forgotten as you use the product everyday. Highly recommend.
Loren
12/5/2018
Still just as satisfied with it. Looks great, truck looks good with it on, Id still recommend it.
High quality cover that works great
Quality product. Bought to protect and hide fifth wheel hitch. Does a great job!
Do you have a question about this Tonneau Cover?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Loren
12/5/2018
Still just as satisfied with it. Looks great, truck looks good with it on, Id still recommend it.