See what our Experts say about this Valterra RV Sewer Hose Fittings

• Looking For Hose Coupler For 3" Waste Hose
  Hey Tom, thanks for reaching out. We do carry hose couplers that fit 3" sewer hoses, but nothing with lug fittings on both sides. What we have are couplers like the Valterra Coupling for RV Sewer Hoses # F02-2025 which fits a 3" sewer hose and secures with hose clamps. I've included a link below that shows our full selection of hose couplers if you want to take a look and see if we have anything that could work for you.
  view full answer...
• Replacement Valterra RV Sewer Termination Adapter
  You are correct that 3/8" won't be enough. If you can't use a heat gun to loosen your broken termination adapter like item # T1029-2 off then you'll need to replace what's behind it.
  view full answer...
• Bayonet Termination Lug Fitting for Attaching to Pipe with 3.5 inch Outer Diameter
  Since your current pipe has a 3-1/2 inch outer diameter it most likely has a 3 inch inner diameter (measure this to be sure) which would mean that you'd need a 3 inch spigot to lug fitting adapter like part # T1029-1 as this will slip into the pipe and give you the type standard lug fitting for the standard size bayonets to attach to.
  view full answer...
• How to Replace Spigot Adapter on RV
  If you need to replace the Valterra RV Sewer Termination Adapter # T1029-1, or a similar connector, then you should be able to cut off your current adapter and then install a new adapter using a coupler like part # D50-2935. Be sure to use Valterra ABS Solvent Cement # A05-0303 to make the connection after cleaning the pipes really well so that you get the best connection possible. If you are uncomfortable with this then I recommend checking in with a local trusted shop to have them do...
  view full answer...
• 1-1/2 inch Fitting to 3 inch Bayonet Fitting Adapter
  Hey Chris. The Valterra RV Sewer Termination Adapter - 3" Lug Fitting to 3" Hub item # T1029-2 and the Valterra Eccentric Tank Reducer - RV Gray Water - 3" Spigot to 1-1/2" Hub item # T1041-1 are exactly what you need to connect to the Camco Revolution RV Sewer Hose Kit w/ Swivel Fittings item # CAM39625. You'll want to use the solvent cement item # 3447530889 to complete the installation and prevent leaks. If you have any additional questions, go ahead and click on the box below that...
  view full answer...
• Fittings Needed To Go From 3" MPT Threaded Sewer Pipe To 3" Bayonet Fitting
  You'll first want to attach the LaSalle Bristol Clean Out Adapter for RV Sewer System # 344633703 to your current setup and then you can attach either the Valterra RV Sewer Termination Adapter # T1029-2 or the Valterra Rotating Adapter for Rigid RV Sewer Pipe # T1028 to the unthreaded side of the # 344633703 with some Valterra ABS Solvent Cement # A05-0303
  view full answer...
  
• What To Do When The Bayonet Lugs Break Off Of The Sewer Fitting
  The lugs of a sewer pipe fitting can not be fixed so you would have to completely replace the fitting. To do that you'll have to first empty out the tank, which since your lug fitting has broken off will require you to hold the hose in place to prevent anything from leaking out on the ground. I highly recommend wearing gloves and glasses as well as a mask to safely get through this process. Once the tank is cleared you can then remove the fitting and replace it with a new one. If you...
  view full answer...
• Waste Valve Adapter for 1972 Timberline Marquis 21 Travel Trailer
  All of our hoses and fittings are for the standard fit bayonet which is not what you have. You can either use the adapter # T05-2285VP you referenced to adapt the older thetford fittings to the standard bayonet or if you don't want an additional adapter I recommend replacing current fitting with the Valterra RV Sewer Termination Adapter - 3" Lug Fitting to 3" Hub # T1029-2.
  view full answer...
  
• Bayonet Flange to Attach to RV Waste Valve
  We do have what you are looking for as the part # T1009. This will replace the flange side of your waste valve that you sent in a picture of and give you bayonet fittings you can attach to your sewer lines. It's hard to say but it looks like yours may have been broken off.
  view full answer...
  
• Recommended Bayonet Flange For Waste Valve
  For the bayonet fitting on your valve, you can use the Valterra Rotating Adapter for Rigid RV Sewer Pipe - 3" Hub to 3" Bayonet - Black Plastic # T1028, the Valterra Adapter for RV Sewer Hose - 3" Bayonet Fitting - Straight - Black # T1024VP, or the Valterra Hose Adapter w/ 3" Swivel Bayonet Fitting - Black # T1024-2VP. For the other side of that bayonet, you may be interested in the Valterra RV Sewer Lug Fitting with Flange - 3" # T1009, the Valterra RV Sewer Termination Adapter - 3"...
  view full answer...
• What Schedule Of Pipe Does Valterra RV Sewer Adapter - Item # T1029-2 Fit
  I contacted the manufacturer and the Valterra RV Sewer Termination Adapter, Item # T1029-2, fits standard ABS sewer pipes for RV uses. It is made from a very sturdy plastic and you would use something like ABS Solvent Cement, Item # A05-0303, to join the pieces.
  view full answer...
• Holding Tank Fitting 3 Hub Fitting
  The closest match that we have is the Valterra # T1035-2 RV Sewer Elbow. The internal measurement on the spigot end is 3" and is meant for a glued connection rather than a push together connection with an o-ring.
  view full answer...
• Semi-Permanent RV Sewer Connections Made To Septic and Fresh Water Supply Needed - 75 Feet
  Your fresh water hose is an easy recommendation, I suggest the Camco RV drinking water hose, 5/8" diameter at 75' Long, # CAM22803. This is a reinforced PVC hose for drinking water made of FDA-approved materials and BPA-free. Because you state that you are new to RV living I will make the suggestion that you also use a water pressure regulator, I suggest the Camco RV Water Pressure Regulator, # CAM40055. Please see the attached video for a visual of product. Because inconsistent water...
  view full answer...
• How Does a Hose Get Glued into Valterra RV Sewer Termination Adapter T1029-2
  When gluing a new spigot or bayonet fitting use ABS glue. There should be plenty of surface area on the hose for the glue to work. You may have to bunch up the hose some if it doesn't have a what is essentially a collar at the end of the hose. If you have to do that then be sure to secure the bunched up hose after the glue has been applied and inserted in the connector so that it doesn't try to unfurl.
  view full answer...
• How to Connect an RV Waste Sewer Hose to a Portable Tote Tank with Threaded Fitting
  I think I'm following you. It sounds like your portable tote tank has a threaded fitting, but your sewer hose has a bayonet fitting like a typical sewer hose. If that is the case, then I have a solution for you, but we don't have a single adapter. Instead, you will want to use fitting # T1029-2 and fitting # 344633703 to make the adapter you need. The non-threaded end of part # 344633703, will fit into the end opposite of the 3 bayonet lugs on part # T1029-2. You will want to use ABS...
  view full answer...
• Will Sewer Hose with Broken Pins Fit Female End of Valterra RV Sewer Termination Adapter T1029-2
  Since your hose still has the connector on it just minus the pins it may or may not fit into adapter # T1029-2. But to be sure you can measure the outer diameter of the end of your hose in question. If it is roughly 3-1/2 inches then it can fit the female end of the adapter which has a 3-1/2 inch opening. Use solvent # A05-0303 to join the pieces. I have also included a link to the hoses we have should you decide to just replace the hose.
  view full answer...
• Replacement Waste Valves For A 2014 Winnebago Journey
  Hi Greg, Without seeing the setup it's a bit hard to say exactly what is going to be the correct fit for your motorhome. If you want to take a few pictures at different angles so I can see how your system is ran I'd be happy to help find the correct fit. Are you just needing to replace the gate valves # T1003VP or does the whole assembly need to be replaced? The # T84 has hubs on each side to slip over 3" straight pipe and comes with lugs and a bayonet cap, making it complete. The #...
  view full answer...
• Will The Camco RV Sewer Drain Cap # CAM39463 Fit a Portable Sewer Tank With 3" Outlet?
  The Camco RV Sewer Drain Cap # CAM39463 is designed to fit a standard 3" Outlet # T1029-2. This is the standard size and it has the 3" inner diameter you mentioned.
  view full answer...
• 3-Inch RV Plumbing Adapter with Lug and MPT Fittings
  Thanks for clearly describing the RV plumbing fitting you need. For a 3-inch adapter with lugs on one end and male pipe thread (MPT) on the other use part # T1029-4.
  view full answer...

Do you have a question about this RV Sewer Hose Fitting?