See what our Experts say about this Valterra RV Water Inlets

• Recommended RV Water Inlets For A 2005 Exiss Horse Trailer
  Hey Lagina, If you're just looking for a water inlet then we have single (city water or potable water) or dual inlet options available. For a gravity fill water tank inlet you can use # A01-2003VP (white) or # A01-2003BKVP (black). We also offer lockable versions so others can't mess with your water inlets # A01-2002VP (white) or # A01-2002BKVP (black). For city water inlets we offer the # A01-0170LFVP (white) and # A01-0169LFVP (black) with surface mount flanges. For recessed flanges...
  view full answer...
• Recessed and Lockable Gravity Water Fill Ports For a Camper
  We actually have a selection of recessed gravity fill ports that you can use on your camper that are lockable. I will list them for you below. Slide-Out RV Gravity Fill Inlet with Lockable Latch - Polar White # 37237525 Valterra Lockable RV Gravity Fill Water Inlet - White # A01-2002VP Valterra Lockable RV Gravity Fill Water Inlet - Black # A01-2002BKVP Valterra Lockable Dual RV Water Inlets - City Water and Gravity Fill - Plastic Valve - White # A01-2004VP Valterra Lockable Dual RV Water...
  view full answer...
• Does Valterra City Water Inlet and Lockable Hatch Have A Check Valve
  The Valterra City Water Inlet and Lockable Hatch, part # A01-2000VP does have a check valve. I have attached a photo of the fitting with the cap off and have an arrow that is showing where the check valve is in the unit. It is behind the red washer and screen.
  view full answer...
  
• Will the Valterra # A01-2000VP Work if Inlet Locations are Swapped on OEM Hatch
  Since the gravity fill and city water inlets usually have a hose connected behind them you should be able to swap out your current hatch for the Valterra # A01-2000VP without a problem. I recommend taking your current hatch off to check that you have enough room for the hoses to reach (which you should).
  view full answer...
  
• What Does Carded Valterra Lockable Dual RV Water Inlet Mean
  The only difference between the carded and non-carded Valterra city water inlets that I'm seeing is the "carded" versions come with all of the parts needed for installation like what you can see with the Valterra Lockable Dual RV Water Inlets # A01-2000VP that you were looking at. The ones labeled as "non-carded" don't come with the installation parts.
  view full answer...
• How Much Work Is It To Swap Out A Dual Water Inlet With The Valterra lockable Dual Water Inlet
  The Valterra Lockable Dual RV Water Inlets # A01-2000VP is very similar in size but without knowing the actual cutout hole dimensions it's not possible to know if you'll need to make modifications. This dual inlet box requires a 5-7/8" wide x 4-3/4" tall cutout hole. Worst case scenario you would have to trim the cutout hole a bit larger to fit this new inlet box in place. You'll want to use butyl tape # AL28FJ on the mounting flange and non-sag sealant # 344270341437-1 around the outer...
  view full answer...
• How to Correctly Orient the Valterra RV Water Tank Part # R8030
  There are a total of six 3/8" threaded ports on the Valterra RV Water Tank part # R8030. There are two on the top of one end and two on the bottom of the other end. There is also a center port on each side. Only one of the holes comes tapped from the factory which is the one with the red cap on it. The other ones would need to be punched out to use. Basically you will want to flip the tank over so that the holes on the top are towards the Valterra City Water Inlet part # A01-2000VP. This...
  view full answer...
• Replacement Dual Water Inlet For A 2005 Exiss 414 Horse Trailer
  Hey Lagina, We offer a few different dual water inlets so you'll want to measure the cutout hole and overall dimensions to make sure that the replacement will be a fit and not interfere with any other trim or accessory that could be mounted on the wall of the trailer next to it. The Valterra Lockable Dual RV Water Inlets # A01-2000VP (white) and # A01-2000BKVP (black) are a pretty standard size for most trailers so I'd say these are likely going to be what you need. They measure 7-5/8"...
  view full answer...
• Filling Freshwater Tank on RV Through Valterra City Water Inlet # A01-2000VP
  What you'd want to do is use a valve like part # CAM2003 attached to the garden hose you'd use to fill through the tank and then on the opposite end attach the # CAM36601 which you would use to direct the water into the tank.
  view full answer...
• Will Valterra Lockable Dual RV Water Inlets Fit 2023 Escape Trailer
  We do not have a way to know if the Valterra Lockable Dual RV Water Inlets # A01-2000VP will fit a 2023 Escape Trailer. What you will need to do is check your cutout dimensions on the trailer itself. This is designed to fit a 5-7/8" wide x 4-3/4" tall cutout. If that is what you have it will fit. If not, you would need to enlarge or fill in the cutout to install the panel.
  view full answer...