This roof vent has a single-speed fan that circulates air, and it opens quickly and easily with the spring-loaded handle. The handle locks the translucent white, wedge-shaped dome into 10 different positions. Install kit and garnish sold separately.
Features:
Specs:
Note: Not for use above tubs, showers, or range cooking surfaces.
The easy-to-use handle on the E-Z Lift Ventadome lets you quickly open and close the roof vent from inside your RV. Unlike a standard handle or knob that can take time to crank, the handle on this vent is spring loaded. Simply pull on the handle and move it into one of 10 positions to open the vent. Each position offers a different degree of opening, and the handle locks into place. Also, the handle's T-shape makes it easy to grip.
There are 4 mounting points built into the flange of this roof vent. These points allow you to install a vent cover (sold separately) over the roof vent.
Installation Instructions
Note: Interior trim piece (garnish) and installation kit with screws and sealant are sold separately.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today we are going to be taking a look at part number V3094-601-00C. This is the Ventline E-Z Lift Vetadome Trailer Roof Vent. It's going to feature a 12 volt fan. We are going to have an aerodynamic wedge shape dome that is going to be made from a durable polypropylene construction. The dome is white in color and it's going to be translucent so it is going to allow a little bit of light through. Here on the bottom side, we are going to have a very easy to use handle. This is a T handle, it is going to control the opening and closing of the lid.
A little bit different design, typically you are going to have the hand dial that you're going to have to rotate. It takes a little bit longer to open. This is very quick and easy, you don't have to worry about any gears, and its faster to operate. Its going to offer ten locking positions to secure it in place, even when you're traveling. All you have to do is lift up on it, spring loaded design, rotate it and its fully open. Then you have all its positions in between that can allow you to adjust how much you want the lid open.
This is fully open, with it fully open you can see the internal components. You can see the fan, that's going to be an eight blade, white fan. You're going to see the wiring, you are also going to see it has the perimeter weather shield to help keep out the elements. Now we go ahead and close it all the way and that's going to be fully closed. It's going to butt up against that nice weather seal and create that seal that we are looking for to keep moisture and dirt and debris out. Now if dirt and debris get in there, we do have this snap out screen.
It can be easily removed to be cleaned or to be replaced if needed. That's a great feature to have, and again the T handle is spring loaded so as soon as you let go of it, it is going to go to whatever hold that the tab match up. You're also going to have your on and off switch to control the on and off function of the fan. On each side you're going to notice that it has two mounting tabs. This is for installation of a vent cover, vent covers are sold separately. It is also going to have the slots right here to accept the interior trim piece or garnish, that's going to be sold separately as well.
Now when it comes to the mounting flans that's going to measure a quarter of an inch thick, that's going to be UV resistant material. Very safe to install, you don't have to worry about any sharp edges. It's going to work well with all roof and materials, multiple mounting holes that goes around the entire perimeter of the vent for a nice secure installation. Your hardware is not included with this part number. When installing this, it is a good idea . We recommend using a weather resistant caulk or sealant to help create that nice tight seal to prevent moisture from getting inside your camper, RV, or enclosed trailer. This is designed for 14-1/4" x 14-1/4" rough openings. We'll take a look at the overall width here measuring from edge to edge, that's going to give us a measurement of about 16-1/2 inches. Square design, so it's going to measure the same going the other direction as well. Then you're going to have your three wire design, so you're going to have your white, black, and green. White and green are both going to be ground wires, black is going to be for power. The product is made right here in the USA but it is certified to be used in Canada as well. That's going to do it for today's look for part number V3094-601-00C.
Fast delivery
Do you have a question about this RV Vents and Fan?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.