To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
These custom tie-downs bolt right to your truck’s frame for a solid, stable connection that keeps your camper steady no matter how far you travel. Because the frame is the strongest part of your vehicle, mounting here spreads the camper’s weight evenly and lowers its center of gravity. That means less sway in crosswinds and better handling on the road, so your setup feels planted and confident mile after mile.
Each tie-down is built specifically for your truck and uses pre-existing holes in the frame, so there’s little to no drilling or modification required. The brackets mount tight to the frame with minimal loss of ground clearance, keeping everything tucked up neat and tidy underneath. It’s a straightforward bolt-on install that you can handle with regular tools.
The tie-downs are made of high-strength steel and finished with a high-impact powder coat that adds an extra layer of protection from wear and weather. That means you get dependable strength for thousands of miles, even when you’re driving through rough terrain or winter conditions.
When you’re not hauling your camper, just remove the tie-down arms and the brackets will be barely visible beneath your truck. The design keeps your vehicle’s lines clean without bulky hardware hanging down. When you’re ready to load up again, the arms slide back in place quickly so you can get on the road fast.
Each arm includes two pin holes so you can extend it for the best reach to your camper’s anchors and clear any sidewalls or fenders. Two anchor holes on each tie-down let you fine-tune your angle for a secure hold from multiple directions. That way, your camper stays locked in tight without shifting or sliding around as you drive.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hi, everybody, Andy here with etrailer.com, and today we're gonna take a look at TorkLift custom frame-mounted rear camper tie-downs. These tie-downs provide attachment points at the rear of your truck bed for securing a bed-mounted camper. These are custom fit tie-downs and they are designed to fit the 2019 and newer Ram 2500 with either a 6 1/2 foot bed or an 8 foot bed crew cab with board or step extending under bed and with a factory-installed hitch, or with board or step underneath cab and with a factory-installed hitch or without board or step and with a factory-installed hitch. So on a custom fit part like these tie-downs, I do recommend using the fit guide on our website and enter the year, make and model of your vehicle. And our fit guide will let you know if these tie-downs will work for your vehicle. The frame-mounted design ensures excellent handling because securing your camper to your truck's base, instead of its bed, better distributes weight to keep your setup from being too top heavy.
These brackets fit tight to the truck frame, so there will be no loss of ground clearance. And these are steel construction with a black powder coat to resist rust and corrosion and these inserts can be easily removed. They do come with these bail pins so they're very easy to detach and remove. And so once you remove these inserts, let me bring this back into frame here, your tie-downs are going to be virtually undetectable when they are not in use. These inserts do have two different holes that the pins go through, so if your camper is a little bit wider you would use this first hole on the insert to have that tie-down point stick out a little bit farther, and if your camper is a little bit narrower, you can move it into this hole and then secure it with the bail pins as I will do here.
And I'm gonna bring that in all the way so it'll fit on my table and then I'm going to come alongside here, make sure I've got the holes lined up. And again, it's very easy to secure that pin. So this is going to give you a secure connection point for your turnbuckles. Now you are going to get two rear tie-down inserts, frame brackets, and the necessary hardware that you see here, with the instructions. And you also get two stickers to put on the ends of those inserts.
These are made in the USA and they do have a limited lifetime warranty. Well, that's gonna conclude our look today at these camper tie-downs. I do hope that they we're helpful for, I do hope this was helpful for you. Again, my name is Andy. Thank you for joining me..
Ratings & Reviews
Lazer S.
9/16/2025
It definitely is safe the way you have them, Paul! In a perfect world, the turn buckles would be perfect vertical, but this an imperfect world and not all campers have the attachment points in the same place. If you take a look at some of the installed pictures on the TorkLift Locking FastGun Turnbuckles # TLS9529-2-LK page, you can see most of them are at an angle. It's perfectly normal. Are you running any suspension enhancement on your Silverado?
Paul
9/27/2026
These tie downs are great, so easy to use. Camper never budged a hair
Andrew N.
9/27/2026
Bob
11/1/2025
I have not had any issues at all with the tie downs.
Kate F.
8/10/2026
Thanks for the pictures Rich. We will be reaching out =)
Heather A.
4/10/2026
Looks great! What kind of camper do you have?
Lazer S.
10/14/2025
Install looks great, Megan! Especially for it only taking two hours! They were moving. : ) Happy we confirmed what you found as well. Tie downs can be a pain in the rear with all the options out there. Now I do have to ask though, have you guys thought about any kind of suspension enhancement for the rear axle? It's a little hard to tell, but it looks like the back is sagging a bit in your last picture.
Lazer S.
10/14/2025
Clay
7/31/2026
A year later and I would not do anything different. Absolutely the best system available especially paired with the fast guns. The camper is solid mounted and does not move. Yet can still be off loaded in just a few minutes. Remember good stuff isn’t cheap and cheap stuff isn’t good.
Christopher H.
7/31/2026
Kate F.
6/5/2026
Great set-up Viviana!! Glad to see you went with the best =) Where did you go for your first trip?
Nick S.
1/12/2026
I love these TorkLift tie downs, and it is great to hear you are liking the quality as well. What kind of truck camper are you going to be running with these?
Kate F.
8/20/2026
We appreciate the kind words Charles! Where did you take the in-bed camper for the first trip?
Do you have a question about this Truck Camper Tie Down?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Straw
8/24/2026
A year later, no issues with tie downs, except normal wear and tear and metal to metal wearrust progression. These tiedowns are designed great and fit function was clearly created by someone who knows not only design but install ! E-trailer is “the” place to buy rv, camper, towing etc products - the install videos are sooooo helpful ! Thx ET !