# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Excellent quality, fast shipping. Finding a metric ball for our international application was a bit difficult. We knew etrailer was the place to go for all things "trailer" related. Very happy with the purchase!
Strong and seems to be well made and well finished. One-inch ball mounting hole. I used this for a Curt hitch mounted on a 2014 Forester and pulls a small Harbor Freight trailer. Perfect height and trailer is level. Warning - don't get their hitch pin, it does not have a hole for a cotter pin, only a weak clip that I would not trust.
# 2
Convert-A-Ball Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10,000 lbs
Makes for a great hard-core dirt road set up with a 3000 pound trailer, in conjunction with the Curt rocker ball, Towing with an F150 over many miles of washboards, down through washes where the road was washed out, etc. Really makes for a gentler set up on the equipment in the trailer and the truck. Thanks a lot E-trailer!
My usage of your hitch is a bit unusual, I think. I pull a two ton roller with my Ram and I've used your cushioned hitch to smooth out the process. The roller Lunette just dropped over a 2" ball and then banged and jerked on the ball neck. Check out the photos for my adaptation.. I can flip it over and use the 2" ball! Have enclosed some photos. The cushion is holding up very well and it takes a beating!! Thanks
# 3
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
I am using the hitch for a car dolly and a bike rack. The fit is a little loose for the bike rackmI'll see it really works when get on the road.
Quality is excellent. However, it did not work so I am not sure what to do with it. I thought I could use the top hitch for a Bike rack and pull a utility trailer with other toys. The trailer is too close to make a turn so good try but not able to use it. Thank you for asking. I did not open the box for a while because I was having the trailer worked on so assumed I waited too long to return.
# 4
Curt Class III Ball Mount with 2-5/16" Ball - 2" Drop - 7,500 lbs
etrailer is great! My hitch shipped quickly and was packaged well. Plus customer service has been great keeping me updated and staying in touch with my order.
Everything arrived on time and well packaged. I installed a Curt hitch receiver to go with this ball mount. Installation for the hitch went exactly as described and was fairly simple for even a novice like me. Very pleased with etrailer.com and with Curt brand products in general. Couldn't be happier with the process from beginning to end. And the hitch looks and works great!
# 5
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
Longer stinger let me drop the tailgate on my Tacoma with trailer attached. Replaced a similar but shorter Curt hitch and both are very substantial and well made for the weight of my trailer.
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
# 6
Curt Ball Mount w/ Sway Control Tab for 2" Hitches - 3/4" Rise, 2" Drop - 7,500 lbs
I cannot use this ball mount because the shaft is too short that goes into hitch receiver on my one ton Dodge truck. It does not allow enough room between truck back bumper and ball to allow any trailer tongue to be put on ball.
Purchased this hitch as a companion for our Reese anti sway control. The small ball for the Reese sway control fits in the bracket and the 2” drop on the hitch is exactly what we needed to have our Jayco camper level when towing.
# 7
Convert-A-Ball Ball Mount for 2" Hitches - 1" Rise, 2" Drop - 14,000 lbs
Product is awesome. Shipping container was destroyed when it arrived. Product was not hurt.
Was hoping this would help with shock reduction. It doesn't. Has to fit loosely into hitch to function so it slams side to side and front to back. Would not recommend. Very disappointed in this purchase. Trailers service is exceptional. Easy to order. Arrived quickly, well packed.
# 8
Draw-Tite Ball Mount for 2" Hitch - 1" Rise, 2" Drop - 8-1/2" Long - 12,000 lbs
Perfect fit for hitch I bought this for. Weld looks good. Dimensions are accurate.
Quality seems good even though it’s made in China. Welds are perfect. I love these Zinc plated drawbars with the solid shank. In New England the cheap painted steel ones with tube shank rust out from the inside. Hopefully the plating holds up as long as the older US made ones we have.
# 9
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
Allows me to open the tailgate on the truck with a trailer hitched up.
Ball mount is the perfect length and well made.
What our customers are saying:
"The phone operator was very helpful and made my purchase easy. I will keep this website handy."