# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Excellent quality, fast shipping. Finding a metric ball for our international application was a bit difficult. We knew etrailer was the place to go for all things "trailer" related. Very happy with the purchase!
Strong and seems to be well made and well finished. One-inch ball mounting hole. I used this for a Curt hitch mounted on a 2014 Forester and pulls a small Harbor Freight trailer. Perfect height and trailer is level. Warning - don't get their hitch pin, it does not have a hole for a cotter pin, only a weak clip that I would not trust.
# 2
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
I have two of these. My first I bought two years ago. I very highly recommend this Curt Class III Ballmount 2" Drop because of its price, durability and quality. I towed various class 3 loads with ease and confidence with this ballmount. It slides into the hitch and does its job without fail. It looks excellent after towing a load. etrailer's price is about as good as it gets and delivery is very speedy.
Easy install, took around 30 minutes by my self to install. Hardest part of install was torquing the bolts ! Installed 13322 Class III Hitch - Gm 1500/2500 Pickup and Curt Class III Ballmount -2ball-2 Drop
# 3
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.
I am very pleased with the hitch, ball mount, and electrical package. All were easy to install if you follow the easy to understand directions. An added plus for putting one of these on a MINI is that the hitch can be hidden behind the "black plate/cover" that is on the rear bumper. It looks just like it came out of the factory except when to need to install the ball mount. The service has been outstanding. This is the place to go.
# 4
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
I have a custom made tow guard. The ball mount I have was too short to allow me to attach the tow guard to my new truck. I searched the web and found just what I needed at etrailer.com. It's the only site I found that carried the size I needed. The product fits my needs perfectly. I can now protect my boat from rocks and other road debris when towing. Thank you etrailer.com.
# 5
Curt Class III Drawbar - 2" Rise - 4" Drop - 13" Long - 7,500 lbs
Haven't used it yet. I bought it because of CURT's quality. It was beat up in shipping though.
Exactly what I needed to extend the reach of the ball beyond my rear tire carrier WITHOUT losing any tongue weight capacity! I used mine for the 2" rise.
# 6
Curt Ball Mount w/ Sway Control Tab for 2" Hitches - 3/4" Rise, 2" Drop - 7,500 lbs
I cannot use this ball mount because the shaft is too short that goes into hitch receiver on my one ton Dodge truck. It does not allow enough room between truck back bumper and ball to allow any trailer tongue to be put on ball.
The ball mount was a complete failure even after a lengthy discussion on the phone. I wanted a ball mount that would accept the rocker ball and anti-sway bar. The bar sent to me can't be used this way. An email and phone message to the sales person I ordered with, got no response.
# 7
Trailer Hitch Ball Mount 10" Drop, 7,500 lbs
Love “etrailer” !! Always have what is ordered and send the item very timely. I always check with etrailer first as they are well stocked. Thank you etrailer.com!! Also George!
Great price and fast ship.Thanks
# 8
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
The one foot ball mount works great on a 2014 Chevrolet Silverado work truck(no lift kit). We use it for a one axle, lawn care/utility trailer. It is used at least half the work week and has held up for a year. It may not be a good choice for a heavier trailer, but at that point we would also purchase a 2500 truck too. The mount helps clear the jack when the tailgate is opened with about 2 inches to spare.
Great product for getting out past the tire carrier on a small SUV. Customer service was wonderful with great follow through and any assistance I needed I will definitely use etrailer agin
# 9
Curt Class III Drawbar - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
A very solid replacement for the stock Bronco hitch. Fits perfectly.
Product appears to be solid but it’s just a paperweight without a locking pin. Since your tow bar doesn’t come with one either it’s just another piece of metal. Product should include locking pin. No satisfied at all
What our customers are saying:
"Thank you! I enjoyed shopping your site."