Most Popular Above Bed Rails for GMC Sierra

Etrailer sent me a one year follow-up email. Since purchasing this I've used it to tow our 11k lb camper about 5k miles. The hitch and slider have worked exactly as they should and I have no complaints.

Click to Enlarge

Well, I haven't towed with it yet but we'll see how that goes. I purchased this hitch because I needed to drop the height as much as 6 inches. My previous hitch was dropped to the lowest setting and still 17 inches high! This E16 goes down to 14 inches... Assembly was straight forward and all pieces were present ( even 4 big washers which were not illustrated anywhere in the instructions as to where they went) The hitch seems well built but the welder needs to be more thorough in cleaning his Slag (got my finger good when I picked up the top plate) Stickers were falling off everywhere (my heat gun fixed those) But a couple notable design flaws... The top cradle for the 5th wheel plate is a triangular shaped arch and the top plate has an axle which is perfectly round. So when the 5th wheel assembly is down in the cradle, there are only two little points of contact instead of the cradle fitting uniformly around the axle rods...we'll see what kind of wear this causes. Next, the green ring on the indicator rod looked like a 3 year old toddler wiped lipstick on it. (Green paint is supposed to be in the little groove cut in the rod but instead, is smeared all over the end of the rod) Lastly... The side plates have a two rows of holes for height adjustment...I have installed the bolts to position the overall height at the lowest possible setting. However, there are two more holes in the tie plate but the casting prevents the sideplates from dropping down even lower. Definitely confused as to what the extra holes are for and disappointed that I can't drop this even lower... Definitely seems heavy duty, but again, I haven't towed yet, so hopefully the play in the base rails doesn't translate into obnoxious clanking and rattling.... If so, I will definitely be doing another review

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

The Curt A16 5th wheel w/ R16 slider is a great looking hitch. I received the hitch on May 11, 2023, replacing an older Reese 15K hitch with a slider lock bar. It was easy to finish the assembly and install. I immediately took my fifth wheel out, using the new hitch with the dual jaw locking system. The ride was amazing. The RV, which weighs approximately 10,000 pounds, loaded, did not buck or rattle, and responded perfectly to the turns, acceleration and deceleration with no issue. It was if there was nothing behind me. The only issue with the Curt A16 is the height. At its lowest setting, the nose of the trailer was up too high. However, by raising the tongue of the RV to its highest setting, I was able to remedy most of that issue. I am looking forward to my trips this year with the new hitch!

So far it works great. Only pulled in a short distance and backed it up into my driveway. Make sure you have help lifting this. Very Very heavy. Directions were average but got the job done. Love the extra turning radius on my short bed F250. Make sure all the parts are there. The handle to release the king pin off the hitch was not in the packaging. The box that the hitch and slide came in were all in tacked and looked good. Emailed etrailer and within a few hours they sent were processing the order for the handle. Arrived in 2 days. That's great customer service.

Click to Enlarge

There was a snafu on the delivery of this, like it ending up 1000 miles from my house on the first try, and then the delivery company getting mad at me for not having a forklift at my house. Since I just got this yesterday I can't say much ab out it yet, I am still trying to install it. I do suggest a hoist in your garage if you plan on removing this hitch at all, it is heavy. It looks to be in great condition though! I can't wait to get it attached so I can give it a test drive on a 2 hour trip. I can tell you that two RV retailers suggested this B&W hitches, so I have high hopes. With all the products on the market today, to get recommendations from two different companies that installs them, is impressive.

From the start,the folks at etrailer were very courteous and helpful. I called many times during the decision making process and everyone was always right there to help. When I finally decided to purchase the B&W 18K Patriot w/slider Bailey was there to help with the order. She explained the free freight shipping and it was a done deal. It arrived 1 day earlier than stated, as soon as I opened the cartons it was in fact the good ol' American made quality I was accustomed to growing up. I proceeded to install on the B&W rails I purchased and installed locally on my 2022 F250 Lariat/ Tremor.I had a small hick- up with the install and etrailer gave me B&W's # as they like to handle issues themselves. Stephanie at B&W was just as courteous. Overall a very pleasant experience. The Patriot was basically plug and play. I then connected my 2021 Grand Design 303RLS Reflection and rolled down yhe road. What a smooth and quiet ride, loved it! I would definitely recommend etrailer and their products. Thank you all that helped.

Click to Enlarge

Click to Enlarge

I purchased both the Curt A16 5th Wheel Trailer Hitch - Dual Jaw - 16,000 lbs - C16120, and Reese Pull Pin Lock Plates for 5th Wheel Trailer Hitches - Qty 4 - RP58093 for my F350 SD 4X4 Crew Cab Long Bed. I'm pulling a 30' Retro 5th. Wheel and at times I pull my tandem axle UTV Trailer (Double Trailers) . I already had the rails installed in my truck, this fit right in and I used the new Pins and Lock Plates for securing to truck. I have pulled all over from South Dakota and the Northwest. The Hitch has performed Flawlessly. No bucking, nor clunking. Very quiet and smooth ride. I would recommend this set up to anyone for convenience of Hook up and Disconnect, Excellent towing, quiet, and the security of the lock pins. I use Disc locks to prevent access for bolt cutters.

Click to Enlarge

I was fully expecting a hitch in excess of 100 pounds to show up in a destroyed box. This did not. They had taken the Time and effort to cover the box with an additional layer of cardboard and it must have had a million staples in it. It was almost comical, you will need a crowbar or large screwdriver to get it open. However, when I did finally get the package open I found a perfectly un scratched hitch with no missing parts. I have not pulled with the hitch yet but , it does look like it is going to perform great. I'm using this in a 2006 ram 2500 4x4 short bed pulling a 2015 forest river Salem and it allows 91 degrees of turning due to the clipped corners on the front cap of the trailer. I will be curious to see how long the rubber isolators last before needing replaced and if they are readily available. Also the curt sticker on the hitch was peeling off when I took it out of the box, would be nice to get that replaced.

Click to Enlarge

Truly happy with this product and can't wait to go to work! etrailer sent me everything I requested and the installer had no problems. Everything was packed well in shipping with no problems.

Click to Enlarge

This product is certainly stout. It doesn't seem to have any ability to rock and roll with terrain which concerns me some.

After ordering rails for a fifth wheel that I had in an older truck, I was told the rails I ordered would work with my fifth wheel, however after installing the front rail, the fifth wheel would not work with the rails ordered. I ended up ordering a new fifth wheel plate. That was easier than removing the frame brackets I had already installed. It appears that there was a mis communication between the person I talked to with etrailer. Instead of a 1/2 day install it took a day and a half plus wait time for the fifth wheel to get to my address. However once installed it appears to be good.

Click to Enlarge

The hitch worked great. Reason for the 2 stars is the package got delayed twice in transit and I had to reschedule the pickup of my fifth wheel. When I also received the package the main crossmember bar was bent at the mounting point. Luckily I was able to bend it back but UPS needs to get there act together.

Click to Enlarge

This product has worked perfect for me using with my 2012 Wildcat Sterling 5th wheel. Customer service is the best at etrailer.com. Just love doing business with them!

I bought a new trailer recently that weighs 16k and I just didn't feel secure using my Reese pro series 16k to Haul with. So I started looking at various hitches. I've had 3 other fifth wheel hitches in the past. All of them have been 15 and 16k models. What I never liked was the latching system. I've even had a trailer come out of the hitch due to a poor latching hook up. There wasn't an good way to lock the hitch. Some of it was my fault and some was a poor design. When I saw the Curt Q20 had a latch on the handle and also was color coded I was hooked. This hitch satisfied my want list. It arrived 4 days after I ordered it and like other comments I've read it was full of heavy duty staples. It was double packaged. There had to be over 50 staples. It was defiantly packaged securely. After dimantaling the packing I finally got to the hitch. There were a few scratches on the hitch from all the staples but a bit of black touch up paint took care of that. After all the hitch is going to be used and get scrached by me anyways. Four bolts and it was together. It fit perfictly it my existing rails. By the way it's heavier than my other hitches. I wound be apprehensive to pull my new trailer. If your looking for a great hitch at a great price you can't go wrong.

Click to Enlarge

We have the turning point pin on our rig so we had to get a wedge. I don't know if it was the wedge or the hitch but unless we were perfectly straight and level, we couldn't hitch up. Same with unhitching. After the 3rd time of not being able to unhitch without taking the entire head of the hitch off, we locked up the turning point and got a new hitch and do not use a wedge. Also, with only a bar going across, the pin seemed to wiggle around a lot.

Click to Enlarge

Shipment was fast, installation was easy, very affordable.

Demco auto slide hitch works very well with my crew cab short bed Ram. Fits under my tonneau cover nicely. Trouble free thus far. Had to purchase a Demco plate for the camper to make the Rhino box hitch work. etrailer personnel were great in helping ensure I had the right products and kept me well informed of shipping dates.

Click to Enlarge

My wife and I are full-time RVers, and have used this slider hitch from the get-go while traveling around seeing the country over the past year. We are happy with our purchase, which has proven to be both easy to hook up, adjust, and functions well, as advertised. The only matter I think you may want to address are the thick plastic removable maintenance access covers which tend to bow, and the areas around the attachment holes have melted, in the hot weather. Perhaps instead using a light metal for the covers would be better solution. We are very happy overall with this hitch, and plan to keep it . Thank you.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Arrived yesterday, box with hitch was broken, UPS driver said he taped it up. All parts look good. Plastic bag with small parts was torn open, 2 small parts missing, I can get them locally. I understand that there heavy Just need to be packaged better. Otherwise all ok.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Nice ride with this hitch . I was kind of on the fence about the pivoting but I’m good with .

This 5th wheel has exceeded all my expectations. It’s worked flawlessly for thousands of miles and many different type of 5th wheels trailers. Not a peep, B&W FTW!!

Click to Enlarge

So far this has been a great hitch. Takes up a lot less space than the massive auto slider hitch that I had previously, and have had no problem with any sharp turns so far. It is also much easier to handle by myself taking it out of the truck. The only thing I’ve had some problems with is getting the handle lock pin out once I’m ready to disconnect. To solve, I’ve started wedging the flat part of my crowbar under the head of the pin and tapping it with a rubber mallet from underneath.

Product is very well made. Glad I went with B and W Patriot Hitch. Once the bed rails were installed the rest was a breeze. Now it's time to get a 5th wheel and hit the open road. etrailer, my go-to website.

Click to Enlarge

Click to Enlarge

Great product and you have to appreciate made in America with American steel! It arrived in good shape in only three days. I ordered on Sunday and shipped the same night. etrailer is great company to do business with!

Click to Enlarge

We have the Anderson Hitch installed on our 2017 Ford SuperDuty and pull a Reflection 337RLS. We have traveled over 4,000 miles and have been extremely satisfied. The hitch allows plenty of clearance between 5th wheel, bed, and the truck cab. Hook-up and disconnect has always been easy, even with RV lots that were uneven dirt lots. I use Curt thin rubber sound dampeners (item 16900) and this provides a quiet, tight fit between the rails and hitch. Of course the light weight makes it easy to remove when not towing and less weight when you are towing. A great product for the right truck, trailer combination.

Click to Enlarge

After receiving the kit i saw another one on the shelf at a local store. I noticed the one on the shelf had a steel ball cup mounted to it. Mine did not have that part. I called andersen and asked if the ball cup was available for purchase seperately. They told me no need to purchase bevause they will ship me one for free! Later on, i towed my trailer to a camp site and upon arrival i could not get the release pin to open to drop the trailer while we stayed in it. I called andersen and described the problem i had, they shipped a whole new block and cable assembly for free!! I am ver pleased with the product and also impressed with the level of customer service!

Click to Enlarge

Great Hitch, very happy with this unit. Have pulled the 18K lb fifth wheel over 25K miles (Florida to Idaho, back to Florida and now Alaska). We have covered many rough roads and challenging situations, without problems and have never had a bad couple. The hitch indicator on front of head gives a clear indication of latching condition, and the latch handle has a locking pin for added protection. This pin is the only issue I have had, which can be trapped under the slide plate if your truck is at an angle (beyond about 35 deg) from the rv. I make it a point to pull this pin prior to backing if I am the least bit concerned. This is a great hitch! Excellent quality and it's made here in America.

Click to Enlarge

This is very well built and operates great. Once I got the first rail positioned and mounted, everything else was very easy. The R20 slider came in a single box and was very heavy. The packaging is not suitable for the weight. As others have also reported, the package was completely demolished when it arrived. Thankfully , all the part’s made it okay and nothing was damaged. I love the product.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Love it. Easy to take apart and move! The instructions were very clear on how to assemble. I pull a 43ft camper and have yet to have any problems! Well worth the $$

Click to Enlarge

I have towed with the Curt A20 for a few thousand miles. I really like this hitch. The visual hooked versus unkooked indicator is awesome. It operates flawlessly. I do get some chucking over bridge expansion joints. However, it seems like most people have this problem. On normal roads it pulls great.

Click to Enlarge

Ive been using this fifth wheel set up for about 5 months now and I don't have any complaints. I pull a 2022 Heartland Cyclone 4006 toyhauler fifth wheel. Loaded down its usually weighing between 18 to 20,000 lbs depending on what we are hauling.

Click to Enlarge

Easy to order from etrailer with fast shipping. Ordered on Mon estimated delivery on Fri but came in only 2 days for a deliver Wed. Curt A25 hitch packaged very well good instruction easy assembly on tailgate filling installed and torqued in less that 30 mins.

Click to Enlarge

Showed up just in time to install and cross a few states to pick up our 1st new 5th wheel. Easy installation and showed up a few days early.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Overall very happy with my Curt 5th wheel 24k hitch. I’m happy it came in pieces because of the weight totally assembled. Release spring for the slide is pretty stiff but I wouldn’t want it disengaging while driving down the road. Thanks for all your help Justin and your prompt service.

Click to Enlarge

I have ran a cheap competitor hitch for several years. A manufacturing defect (welded pivot pin) caused the hitch to fail and resulted in 18000$ damage to my truck and trailer. I chose the Curt 25000# hitch after much research and found it to be very well made and clearly shows when it is properly coupled. It is quiet and operates with minimal klunking and chunking going down the road. Overall I am very pleased.

Click to Enlarge

Mounted this hitch on my flatbed 3500 Ram and the hitch works flawlessly. Pull 44' tri-axle weighing in at 23,000# with ease. Very easy to use and understand, very easy to maintain.

Click to Enlarge

GREAT GREAT GREAT EXPERIENCE AND EVERYTHING THAT GOES WITH THIS WEB SITE.....PRODUCT TO PRICING TO SERVICE.....

Click to Enlarge

Worked perfectly for my application, installation was easy and it has worked with no issues.

Love it works great

Click to Enlarge

Wow, where to begin. I can't imagine towing a 5th wheel trailer in a shorter bed truck without an autoslide setup. After the initial install I noted on the 2nd(?) trip a clunking noise during acceleration after a stop - a couple emails back and forth with Demco support, as well as a quick phone call, and it was all sorted out (user error) with no further issues - Thank you Demco! I tow a short & light Jayco 5th wheel with a 1/2 ton shortbed and having the ability to drive, turn, and park the camper without having to get out of the truck to manually engage or disengage a slide on the hitch has made for much more relaxing weekends away. The Hijacker autoslide gives PLENTY of space between the camper and cab and I've never had to worry, but I did my homework and ran the numbers well before I purchased my hitch so I wasn't surprised. I would say the only downside for me would be the weight and bulkiness of the hitch. Not having the means to easily remove and store it between trips, the hitch is forced to live in the bed of the truck right now, but I did know about the weight going into the purchase. All in all, for the peace of mind the Demco autoslide gives me, I'd spend the money all over again.