Summer Starts Here - Save up to 70%
# 1
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Shipping was fast and packaged good with no scratches. I modified my 2010 Tundra skid pan for oil filter changes before mounting. Replaced all 4 OEM tow ring bolts using anti-seize with new longer M12-1.25 X 40MM class 10.9 zinc finished hex cap screws along with new M12 X 24MM OD HARD WASHERS and torqued all 4 to 79 ft/lbs. Mounted new Thule EasyFold XT 2 Hitch Bike Rack and it fits in front without using the hitch extension. All went together as planned and can now take E-Bikes with us while pulling our camper. We are happy campers!
Primarily bought the front receiver hitch to haul our 2 e-bikes. Did that because it was easier than hauling them inside our camper. And didn’t trust them bouncing around on the back bumper of the camper. Hauled the bikes that way on several camping trips. Easy as pie and I could keep an eye on them the whole trip.
# 2
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
2022 TRD Pro fits snugly. To keep the OEM skid plate, you can remove the skid plate’s 2x front spacers and spacer washer locks. Removing this will allow you to fasten the front 2x M10 oem bolts. The 2x rear M10 bolts will need to be replaced with 2x smaller length M10 bolts that are at half the size of the oem bolts. My local hardware store had plenty of options.
This is the second hitch for my Toyota 4runner The first one you sent me was wrong. The box came in with had holes in it. Today I received the correct hitch. I’m assuming the correct hitch I haven’t had it installed yet I hope it’s the right one, but it came in the box, and it was all tore up. both ends of the hitch are sticking out of the box of the new one I just received. That’s pretty much the same condition that I got the other one. I’ve ordered hitches parts from you for years never have I never gotten product that was sticking out of the box. Unacceptable. I just hope it fits.
# 3
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
1996 Chevrolet SuburbanI have had the front receiver hitch installed on my 1996 Suburban for about a year now. I have a 12000 lb winch installed using that receiver hitch. I have gotten stuck twice and had to use the winch to extract the truck. Very glad that I have the front receiver hitch as it made putting on the winch very easy. Also useful for mounting a receiver mount bicycle rack to the front as well.
Product was shipped promptly and arrived a few days later. Packing was good for a heavy item with pointy edges, no issues breaking out of the box. Installation on a lift took about 30 minutes on my 1999 K2500 Suburban. The bolts were long enough to allow for my tow hooks that were already in place. A bolt stringer to pull the rear bolts from the top (inside the frame) is provided along with nuts, the other four just replaced the stock bolts that I had that mount from the bottom into tapped frame metal through the tow hooks. Curt makes great quality stuff. Clearance was reduced a little but I'm not concerned about it.
# 4
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I bought this receiver to add front mounted 'accessories' on my 2007 Jeep Wrangler Unlimited Sahara. I plan on using this to add an extra bicycle rack, a cargo basket, a receiver mounted winch or other 'accessories' needed for my Jeep when I take my family camping. It will also be useful for "front launching" a boat or parking a trailer in tight spots. It took me about an hour to install, although I had already previously removed the lower wind deflector cowling, so did not have to spend time removing it or cutting it for a finished look. Detaching and moving the top trim panel between the grill and the bumper is a must to facilitate the installation. The receiver fits pretty close, although you do have to manipulate it to get the holes to line up with the frame. Follow the instructions and do not tighten any of the bolts until you get it lined up and all the bolts in loosely, then torque it down. As noted in the instruction sheet, the driver's side of the receiver does not sit flush against the frame, there is about a 1/4" to 5/8" gap. The instructions say to use the extra split washers (in the kit) as filler, but they would just rattle around loose in there and provide any benefit, so I omitted them. Once tightened down, the receiver tube was not parallel to the ground, it is slightly higher in the front, sloping towards the rear. It is not off enough to affect my intended use, but may be bothersome to those with type 'A' attention to detail. Overall a good product that will add a lot of flexibility to my Jeep~
Relatively easy install. Just have to be mechanically inclined. We use the hitch to carry a fish rack/cooler on a 2011 Jeep Wrangler. So far so good.
# 5
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Quality hitch and the excellent service all the way around I'm used to getting from etrailer over the years. Installed on my 2016 Sierra Denali 2500HD, note instructions say on first line down that it does not fit the Denali trim due to extensive fascia cutting required; actually it was quite simple with the aid of a 4-1/2" cutoff disk and a sawzall. Installation is much easier with two people. See attached pics for actual material removed, note the lower fascia need not be cut for the hitch to fit through the hole. Maybe more work to install than the Curt hitch, but well worth the additional ground clearance.
The hitch was easy to install. The only issue is who ever welded it put the front ring on and it's turned to one side. It functions fine but bothers my OCD.
# 6
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Just what I was looking for. Thank you.
I ordered these two, front and rear for a 1990 GEO Tracker 4 wheel drive that I am rebuilding. I believed they would fit, I finally got around to mounting them and they don't fit, to large. I think I have had them to long to return them.
# 7
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
We live just south of Buffalo and Put this on our '11 Honda Ridgeline with a snowsport plow and a week later it snowed, and snowed and snowed... 5 feet in 24 hours and it's still snowing.... It's not good.... It's AWESOME! Not one driveway or even our street is clear... Except ours. It was easy to put together , easy to install and works exactly like it's advertised! It's November and it paid for itself already. Communication with etrailer was exceptional. We could not be happier with the whole setup.
Needed a front hitch for a 2006 Ridgeline Honda truck. I found it on etrailer.com and a better price for same hitch on another online store. As I talked with the customer service agent, I was also offered a discount which was quite a surprise. Shipping was very fast. Had it installed on my truck so I could attach a mounting hitch and snow blade. I am extremely happy with this hitch and etrailer.com.
# 8
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I chose Draw-tite because they are built very well and this one is no different. The welds are done well and I have no fear that this product will serve me well. The install wasnt to bad for a DIY type like me and the fit was excellent, only took a few hours. Knowing that I can now be pulled out of a bad situation or pull someone else out is comforting with the help of a hitch mounted winch. The Price was right and etrailer shipped it out fast although packing could use a smaller box . Oh yeah, UPS sure tested the toughness of this receiver ! . Great product and great service from etrailer
im very satisfied with my front receiver. ive used it as a recovery point,to move trailers, and as a mount for bike rack and cargo holder. if i had a winch platethat would be very handy too. etrailerhad a fair price, quick shipping, and overall great customer service. i would use them again andrecommend to a friend as well.
# 9
EcoHitch Hidden Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Bolted right up to my 2019 F-250. Looks like it's going to work perfect to haul my E-bike rack. I might have to use a dual receiver hitch to drop the rack down for better visibility while driving. That's to be determined. I'd highly recommend the Eco Hitch!!
FordThe hitch is great! Super stout. But, installation was a disappointment. There was a significant gap between the frame rails on the Ford. About 3/8 inch. Did some research and it seems some frames are different but can't confirm. I happen to have a piece of 3/8 steel plate that I was able to cut and drill and slide it in to take up the gap. Definitely extra work I wasn't planning on doing. I guess I'd still buy it again but if you're going to pay someone to install it then make sure they put a nice spacer in there and bot a bunch of washers. Again, not sure is this is a Ford inconsistency or an eco hitch problem. Because it's a hitch and needs to be 100% solid this should be looked into.
# 10
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Great products, great prices, fast shipping and a great company to do business with. Easy install, and it took longer to trim the air dam than installing the hitch.
I have had this hitch installed for just over a year now on my '99 2-door Tahoe. The install was pretty straight forward, and the hitch itself has held up quite well through a year's worth of abuse. I use it to run my bike rack out the front; the receiver protrudes just below the factory front bumper, maximizing ground clearance when adding length to the front of the vehicle. And as you can see, the kit comes with two sets of hardware in case you want to maintain the factory tow hooks like I have.
# 11
EcoHitch Hidden Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Perfect hitch for those needing a rack for extra space. I used a heavy duty vinyl bag to enclose my tools, cords and generator on my 12k mile trip to alaska. The held that 500lbs extremely well across the permafrost damaged Alaskan highway! No twists, no bends and no worries!
Just what I needed. The hitch fit perfectly, all parts were there and the installation instructions were very clear.
# 12
EcoHitch Invisi Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Review for truck front hitch receiver I finally Installed the front receiver hitch today, I pulled it out of its package and found all parts wrapped to the receiver hitch good call as there was a hole in the box. The license plate holder received some damage it was bent some. Installation. I reviews the video prior and read the instructions. Had to purchase a 4 inch hole saw and a torque wrench that added to the cost of the hitch. Installation was for the most part straight forward, when the video cuts from shot to shot I now know all the cussing and swearing are done during that time as it’s very difficulty to get the hitch in over/under the exiting hardware, solo installer took me 3.45 hrs to install, tight fit under the truck to maneuver under the truck. Bolts back into original tow hooks was a total Pain in the A$$ trying to hold up the hitch and the hooks while trying to maneuver the hold back in. (Had to take it out as I inserted on the wrong side) I will say that installation is doable by novice front yard mechanic but with a difficulty of 7 out of 10, trying to get the bolts torqued to specs is difficult due to clearance and angle of the bolts. Make sure you have deep well sockets because the new bolts for the hitch and long and a standard size socket will not be able to grip the nut as you tighten it down to specs. Put the bike rack on the hitch receiver and found that the hole that we drilled out to put the hitch in is not big enough. The bolt for the hitch goes in from the right and there was barely enough room to get it in the hole, used a wrench to tighten it but it was slow going, the other issue was that on the left side there is a hitch lock I struggled to get it on, but then could not reach in to remove the key. So final outcome was I had to drill out another 4 inch section of the bumper to get to the key. If your hitch has a bolt on bike rack like the swagman e-bike rack you want it to be secure so the bolt is a must this option may not be the best option. The bikes block the headlights so no night driving with the bikes on the rack. The handlebars need to be folded down otherwise the bikes will ride too high on the front and obstruct your vision. If I had to do it again I would have gotten the hitch that is lower and would not have to drill out my bumper, and it would have given me more visual clearance. I did take a shot drive with the bikes in front it will take a bit to get used to them being in the front as well as making wide turns while towing the RV that I don’t take out the car in front of me.
2018 Chevrolet Silverado 2500My friend installed the hitch and I helped . But mostly by staying out of his way!?? Everything worked out perfectly!!! Thank Y’all for the Great Service
# 13
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Road tested 4000 miles & off-road, Solid, Great ! I always wanted a front hitch, it is rad ! We had a great experience across the board. Ordered the front hitch mount and had a mechanic (Weld Tech/San Diego) install it, because they already had our van to install their lift kit. They charged me one hour labor. I can see that it fits well and is solid. We went on a 4000 mile adventure with a small motorcycle on the front hitch. etrailer has been a good source for for a few things now.
I own a 2003 Ford E-450 RV cutaway and wanted a front hitch to carry our bicycles since our rear hitch is used for a trailer. I originally tried to mount the equivalent Curt front hitch, because of its cheaper cost, onto the vehicle. However, the Curt hitch wouldn't work because it can't adequately accommodate the slight downward hump in the truck's frame. This hump can barely be seen between the two hitch mounting bolts. The hump is on both the left and right side frame rails on my vehicle. If your frame is not totally flat (has even a small hump) you cannot use the Curt hitch. The Curt's small indentation on its mounting flange will not adequately accommodate the frame's hump. This Draw-Tite hitch, 65001, mounted perfectly on my vehicle and the installation procedures I used were exactly as depicted in the etrailer video for the E350 van. In the video, the technician uses a rotary file to expand the rearward holes to allow the insertion of the bolts. I had to do the same thing and bought a rotary file for my drill at my local home improvement store for less than $3. I did not have to use the rotary file on the forward holes. In addition, I have the larger Roadmaster front sway bar and steering stabilizer and as you can tell in the photo, there is plenty of room for the hitch.
# 14
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Owner of 2023 4Runner TRD ORP with the KDSS. I purchased this product to give me the use of the front end of the 4Runner to carry my fishing gear while at the beach and other uses on the trails (can't do everything from the back). The fit and quality of this product is A+. The delivery service was extremely rough and there was plenty of paint missing. etrailer was fantastic with their customer support and assisting me with getting things fixed. First-rate product and first-rate company. I will be using them in the future.
Front Trailer Hitch for a 2014 Toyota 4Runner was delivered quickly and in perfect shape. Installation was straight forward, however I spent more time trying to remove the super tight 4 bolts from the frame in order to install the hitch. There's not a lot of room once the hitch is installed to tighten the the upper bolts. I had to use a smaller ratchet in the tight space. I also used anti-seize on all the bolts prior to re-installing them. This hitch will be used for a fishing cooler rack and rod holder while on the beach. So Far I'm very satisfied with this product. Draw-Tight makes a good product.
# 15
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
2007 Toyota TundraThis was one of the easiest accessories I’ve installed on my Tundra. It is a front receiver hitch so I don’t use it very often. Mostly just for bike racks when towing a trailer, but when you need it you need it.
Straight forward and perfect fit on my 2008 Toyota Tundra!!
# 16
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Jeep WranglerFits perfect and works just as I needed it to. I use it for my SnowSport plow set-up on a 2022 Gladiator Sport Max Tow. I’ve been using front receivers for this same plow for the last 24 years. It’s been used on 5 different trucks and this front receiver mount plow is the BEST. *** When installing on a Gladiator(possibly the Wrangler as well), the front plastic trim below the bumper needs to be cut for receiver clearance. I wanted a tight and “factory looking” install, so I took my time with a vibrating cutter and very sharp utility knife. After trying to put it back in place, the hole is not just square, it’s shaped more like. “T”. I suggest you make small adjustments/cuts as you go forward. It may take several times fitting and cutting to get it right and tight, but in the end it does look like it came that way from JEEP. On the Max Tow package, there is also a metal skid plate that does not get reinstalled. Unfortunately that piece is where the back of the plastic fascia mounts. I ended up securing it with some long heavy-duty zip-ties and it’s worked well for a year now. Just an FYI for those installing the same receiver on their same vehicle.
Product shipped and received on time. I'm very happy with the packaging. Hardware was included with instructions to install the hitches I purchased.
# 17
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
A good install! A bit of trimming for my application , but the bolt holes lined up perfectly. This front hitch was not specifically for a Lexus GX 460 but I decided to try it. There is a small area of lower bumper plastic that had to be trimmed. The hitch was pushing up against it before it was high enough to be in place. Upon trimming that area, it went in perfectly. If trimming the lower plastic is not for you, probably best to pass. However for my use, it works well. It is a stout piece, very strong. I added a pic with a red line to show where the trim needs to be.
Installed on my 2012 Lexus GX460. Perfect fit once I cut the center section of the lower plastic area for it to fit. Also had to trim the bottom splash guard and bend in the L brackets that hold it on. Took me about 2 hours. Very happy with the outcome. Now can mount snow blade for the driveway clearing…or any other hitch items.
# 18
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
This worked great on my F350 dually. We needed a front hitch to carry bikes while towing a 5th wheel camper. Instructions were easy to follow
I buy practically all my towing accessories from etrailer. One of the reasons why is that you can tell that they take the feedback of their customers seriously. I read a lot about previously shipped products having fell out of the box in certain areas. etrailer heard that feedback and my shipping box was reinforced in just the right areas that were talked about getting punched through in shipping. The tech notes video on the 2012 F-250 applied exactly on my 2016 F-250. All the measurement specifications were correct as well. This is a job that can be done by one person, albeit you'll have to be careful. Your second set of hands can be jack stands, as it was in my case. If you take your time in positioning everything - installation will be a breeze. I do agree with previous reviews - it would be nice to have a second fishing wire as it does get stretched out when pulling the first bolt through. That, or a heavier duty gauged wire - that's just a small detail however. If you're really concerned about it, you can buy a secondary fishing wire at around 5 bucks. I spent more time taking out and putting back in body clips than I did with the install of the hitch receiver hardware. I really like the way it looks and I'm excited to use it.
# 19
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
This fit my Ford 2023 E-450 (cutaway) perfectly. I had measured the frame of previous year E-450’s and didn’t see any difference so I gambled and ordered the 65053 which fit. Installation was straight forward with modification and fitting of the splash guard taking 50% of the time. Fit and finish was good except at the front of the receiver itself. Unfortunately that’s the only two inches of the whole hitch that show and had weld splatter and sharp bits under the paint. This took a bit of filling to smooth out which I then repainted. Attached are photos installed on my 2023 E-450.
Easy installation, nice sturdy hitch that fits on the front of our C- Class RV to haul our electric bikes. Highly recommend it.
# 20
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Dealing with etrailer.com was definitely easy. They very much so appreciate any and all business. Shipping was pretty quick and they kept me informed on my order status all the way through as well with follow up to make sure everything was satisfactory. I have a 2019 TRD Pro Tacoma, I opted to just replace my skid plate with a lighter one given the slight addition weight of the hitch. On top of the fact I didn’t want to have to cut such a pricey factory part. Everything installed easily and while I’ve never had much reason to use fish wires I can tell you in this situation it’s a lifesaver. If I recall some people had issues fitting a ratchet to the top nuts. I used my stubby bolt through ratchet set and worked pretty flawlessly. Got to say over all I have zero complaints, some people mentioned the loss of ground clearance and/or approach angle but it’s really not that intrusive. I would definitely recommend this to anyone looking to make their Tacoma a little more versatile. My main objective was to be able to use my Surf Mate hitch rod/cooler set up without it getting in the way of the tailgate. Everything works great!
Well engineered product. Less than 30 min to install on my 2022 TRD Off-road. No trimming at all on TRD Off Road model. It looks a little utilitarian up close, but not so much from a distance. My cycle jack worked perfectly for this task. BTW.. The fish wires are a stroke of genius.
What our customers are saying:
"Very helpful/friendly Customer Service. Competitive Pricing. Shipping was Fast."