Most Popular No Load Assist for 2022 Subaru Outback Wagon

This fits 2018 Outback with no issues at all. Comes with all straps and extra for front and back tie down. First time putting them on took about 30min. Every time after about 10-15min. Have a 10 and 11ft kayak and they work perfectly. Etrailer was quick on responses, better priced, and shipped quickly. Will use them again.

I purchased two sets of Thule Hull-A- Port Carrier with Tie-Downs (J-Style, fixed side - loading) last year. They have been installed on our Subaru Outback all of this summer. I like that they are easy to install, easy to use, well built, and that Outback fits under a standard garage door with them installed. Its a snap to pop the kayaks on and go! If you paddle longer boats (my kayaks are 14, 14.5 and 15 feet long) I recommend getting the Thule Bow/Stern Tie Downs (TH530) for convenient temporary bow & stern tie down points, without crawling under the vehicle to attach to the frame.

Well-made high quality product. The kayak racks fit perfectly onto the roof rack of our 2018 Subaru Outback. The one downside was the difficulty in getting the hold-down straps around the top of the loop on each of the racks after the kayaks were loaded on, even when following the strapping instructions to the letter. It would be nice if there were some way of holding the strap in place on the top of the loop without it slipping down.

The rack installs very easily and is mostly intuitive to use. I feel more comfortable with a kayak in the jay low rack than I did with the kayak flat on my old car rack -- the kayak's weight and shape help to hold it into position. The straps are pretty easy to figure out, etc. My only complaint is less about the jay low than about the new Subaru Outback I own. There are no tie-downs locations on the front of the car! So, if the front tie-downs are needed, then perhaps this is not the best rack if you own a new Subaru. On the other hand, I've now used the rack three times without bothering with the front tie-down. Go figure.

The product itself is great and you should feel confident that it will get the job done. However, it said it would fit my 2013 Subaru outback, and while it does fit, the roof racks are not wide enough for the width of the canoe. So that’s something to be aware of before purchasing this product.

Great canoe rack! Fast service!!

This kayak carrier works great with my factory Rav4 roof rack and 10' Tamarack Angler kayak. I did break one tightener knob but probably over-tightened it. And it was replaced for free. I can load and unload the kayak easily and it doesn't budge going down the freeway. I can even drive in and out of the garage with the kayak on the rack for easy storage hanging from the rafters.

Installed this Thule Top Deck Rooftop Kayak Carrier System with tie onto our Thule Roof rack system. Easy to install and this will carry our handmade 17' Wooden Sea Kayak. Very well made.

I purchased the product to make it possible to haul a 30+ year-old White fiberglass canoe on the standard roof-rack of a 2013 Subaru Outback. The kit works very well, but some experimentation was involved. Due to the tapering width of the canoe, I use haul kit with the front guides reversed to face the inside of the canoe gunwhales. In the back the guides are used as intended, facing the outside of the gunwhales.

Excellent product! We have two other sets!

I acquired a second kayak and needed a system to fit the factory racks on my 2011 Toyota RAV4. Etrailer.com has always had information on what fits and has always had the item needed for the job. I attached the Yakima BigStack to the top with ease, and, with one other person to hold the kayaks while I secured, tied two of them down for a long road trip to Northern Minnesota. The system worked just fine. The only caveat was in the configuration of multiple boats in the instructions. The diagram has two boats on the same side of the posts, however, I found it more secure to put one on either side ( other reviews of this product on different Internet sites have found similar results.) The boats made it through the trip with no shifting.

Where do I start? I've been whitewater kayaking for 22 or so years now. I've always used used either Yakima or Thule products... Until I bought a 2015 Nissan Rogue with a naked roof. The curvature of the roof and large door jams mean that Yakima and Thule can't make racks for them. I went to a place that does custom installs and again because of the curvature of the roof, they couldn't give me a rack. This meant no kayaking which is really bad news. Enter the Rhino rack system. I purchased the feet, the fit kit, the cross bars and a Yakima "big stack" stacker. The first issue I had is the reccomended size for the Nissan Rogue is only 48 inches. Way too small too haul 4-5 (very light) whitewater kayaks. I called etrailer and they were SUPER helpful, told me I can buy the 65 in cross bars and they'll work fine. I held my breath and placed my order. I was nervous leaving my trusted name brands. The order arrived super fast (they told me it would arrive by Friday but it actually arrived on Thursday) and everything was packaged rock solid. I was impressed. I read the instructions and put the rack system on my car. It took about a hour (it was hot and I worked slowly) but the rack system is SUPER SOLID. I love it. Rhino might have a "forever" customer out of me. -The rack system is very stable. I can't move it with my hands by pushing or pulling. -The rubber stripping you put on the top and bottom of the bar is an awesome added feature AND it reduces wind noise. -Adding the fairing reduced wind noise even further. With four boats on the roof you couldn't hear any extra noise. The ONE thing I dislike is that you need to use the supplied Allen wrench to take the rack on and off the car. It's a small complaint, but other systems I've used in the past don't have them. I paid much less for this system than I would have if I purchased one of the aforementioned systems, but I'm really really satisfied with the product. We will see how well it holds up over long-term use, but it looks awesome!

Have not used them yet so cannot rate properly until then

Fantastic carrier. Very sturdy and easy to set up.

These kayak J-style racks worked great, AFTER I went to the hardware store and spent $20 on bolts that actually fit my truck rack. It comes with 2-5/8” mounting bolts that aren’t adequate for a heavy truck rack ( mines a Best.Wyle). I had to buy 4” bolts, lock washers, and nuts). I also wish the locking teeth were mitered instead of square. That would make them less prone to breaking and easier to align.

In the meantime, that boy is not to be in this house ever again These kayak carriers are fantastic! They combine with downloaders to make it possible for my wife and I in our advancing years to get our kayaks on top of our car.

These pads worked well on our Yakima RailBar Crossbars- Item #Y00448-0449 that we also bought from etrailer around 2020/2021. Not sure if etrailer carries the exact Yakima Crossbars anymore, but think they have a similar model. Both the pads and crossbars work well to haul our kayak on our 2019 Subaru Forester. etrailer's customer service rocks! We had a lot of questions purchasing both items and they were great to talk to!

The product came quickly and was so easy to install on my existing roof rails! It is absolutely perfect to fit many needs above and beyond my kayaks and paddle boards. They look so good on my new 2019 Jag F-Pace I might leave them on all the time.

I have had about a year to use this and I have no regrets. I have a 2018 Subaru Outback and I have absolutely no trouble taking these on and off. The kayaks load very easy and the carrier’s fold up very nice. They are holding up very well.

The package arrived brand new. No complaint. Now I need to find out if I can install this on my Rhino-Rack universal platform on my 2020 Subaru Outback.

I've owned this product for a year now,and originally bought it for an okt13,and just recently upgraded to a hobie outback. I've gotten a lot of uses out of this so far and have done a ton of kayaking.most of my trips I travel long distance from Pittsburgh to Virginia Beach.so far I must say I love these types of straddles! Very nice support and I like the fact that they allow you to mount your kayak upright,instead of upside down on the bar which results in scratching up the gunnels.definitley recommend this product!

Looks like is quality product, looking forward to using it soon. Prompt shipping, satisfied.

I can now load my 14' tandem kayak by myself. Excellent product.

I don't have an issue with the product per second but my kayak was too wide to effectively use it. I could never get the boat in the right spot on the cradles and just ended up removing the cradle and sliding it directly onto the cross rails. The only complaint I have is the installation method. You have to use an Allen key with a hole for a peg. Unless you plan on leaving the cradle in place all the time, this is a real pain to install. Some quick release cams, like you find on bicycles, would make installation much simpler.

Haven't installed yet but product looks very good and as advertised.

easy to install...very haPPY WITH YOUR SERvice

Great workmanship Instructions are clear and concise Allows for fine tuning once Kyak is on trailer.

Installed it today on my Thule rack. Great product!

The problem: How to transport kayaks with smaller vehicle as weight of cross & kayak racks plus kayaks was above vehicle roof weight limits. So I shopped for a "kayak" trailer. The people at etrailer made the ordering process easy and successful to complete this project. Great trailer, impressed with the size & strength of frame, and assembly went together as instructed. Installed bunk boards and mounted Thule DockGrip for Kayaks. This for me is an easier and safer way to transport kayaks. Thank you etrailer...

I used the rack to carry my wind surfing board for a ten hour trip to outer banks. Installation went well and easily.Loved design and ease to load and unload as well as to secure rack. One caution though. After riding for about 30 miles I stopped to check cable and had to retighten the cables which had slackened slightly due, I think, to amount of cable on source spool. Had to tighten about two clicks. The board was not in jeopardy of becoming separated from rack.

My representative who helped me was the most helpful representative that I have come in contact with. All representatives are very helpful, but she stood out as she assisted me from start to finish on my order. This is exactly why I use e-trailer for my shopping experiences.

E trailer is a joy to work with. Customer Service is second to none.

The Thule DockGlide Kayak Carrier and the Tie-Downs that came with it are a very functional High Quality Product. Once the DockGlide Carrier was properly positioned on the Cross bars it attached easily and solidly with the associated hardware. The Kayak slides on and off the Carrier very easily and is quite secure once properly tied down. I enjoy Kayaking and the DockGlide Kayak Carrier enables me to get where I want to go.

They are high quality and work well but I used them on Thule wingbar evo cross bars which they are almost compatible with. They work with the clamp method but they do not have the right length bolts to use the c channel hardware with the Thule bars. I will eventually find the right length bolts and use the channels because I think it looks nicer and should make less noise with less hardwar sticking out.

've previously used the Yakima Kayak Stacker (old style), which worked fine but I always worried the straps would slip off the hook at the top while I was loading boats. They also didn't fold down, so had to be removed after use unless you wanted to look odd and cause a whistle while you drove down the road. They didn't have a universal attachment option, requiring adapters depending on the style and make of your crossbars. More recently I got the Thule "The Stacker", which is a superior solution. You thread the strap through a closed loop at the top, so you don't worry about straps slipping off while you're loading boats. They fold down after use and have a universal style attachment that fits around most styles and makes of crossbars. Good stuff. I really like the straps that come with these, as there is a rubber cover that slips over the metal cam buckle to protect your car's paint while you're tossing the strap over your boats to strap everything in. In order to shuttle our boats for river trips, we needed stackers to fit on both our cars, so it was time for another set. I had never heard of Rhino Rack before, but the lower price than Thile caught my eye, so I read about them and decided to give them a try. The Rhino Rack Nautical Stack used a closed loop at the top, which I liked better than the Yakima or Malone options, and came with the hardware necessary to install them into the C-channel of my Malone aero crossbars, which I wanted to try. I remember that with the Malone stacker, you had to buy the C-channel mount hardware separately. I really like the Rhino Rack Nautical Stack. They are a single post design, unlike the loop style of the Thule "The Stacker". I don't know if this cuts down on vortex drag, but it definitely saves you a couple horizontal inches up where the boats stack. The Rhino Rack Nautical Stack has textured rubber strips on either side of the post, which I believe is intended to cut down on vortex drag, but is also quite helpful in that boats tend to slip much less when you're just leaning them up against the post as you load up before you strap them. That's smart. The Rhino Rack Nautical Stack feels really solid. The mechanism for folding them down and locking them upright is easy to use and feels solid. Installation instructions were good. I tried to install into the C-channels without removing the rubber tubing in my Malone aero crossbars, but couldn't get the little squares to slide into the slots with the rubber tubing in place, so had to cut the tubing, slide the Nautical Stacks into place, then cut down some of the tubing I had removed and replace it in the remaining unfilled crossbar slot. That's not a knock on the Nautical Stack; just a tip in case you're trying to do the same kind of install I did. The one area in which I was less impressed was the tie-down straps that come with this kit. The metal cam buckles have no covering at all, so I'll probably still use my old Yakima and Thule straps instead and use these as backups. But overall, I think these are going to work at least as well, if not better, than the Thule option, and for quite a bit less money.

The keys are an issue (wish they were metal), but everything else is great! I go sunrise kayaking only and hate putting straps on with cold hands at 3:30 in the morning. I have a Nissan Pathfinder and was able to put this on with another set of Malone J-hooks so that I can have a second kayak when I go with someone. Once the fear subsides of it possibly falling off, you realize how quick and easy this thing is to use. It takes me 1 minute instead of 9-18 minutes to get my kayak up and secure. I have tested it at 75mph without any jiggling or issues. I sat on this in my shopping cart forever and finally pulled the trigger. If you kayak at least 10 times a year or are going at high speeds for extended periods of time in warm weather, totally worth it. If not, well, there are cheaper options out there.

Unfortunately I did not have the best of luck with this product . I spoke with the company multiple times to ensure this would work with my rack. It did not. This system is made to work ONLY on a roof rack . I have a truck with a rack and a slot in the middle . We had to make different bolts and holders to install this. For using 2 Paddleboards we also had to modify the back of the racks holders to actually touch the boards to hold them in place . After the modifications and many many adjustments we have it working and it does hold great.

The carriers are nicely equipped with everything you need to secure your kayak to your roof rack. The only downside is the clamps don't seat well on the Subaru Outback (2017) crossbars. The clamps are shaped to favor a square bar. As a result the actual bar surface area this holder contacts is very little and even when screwed down nice and tight, the boat was able to move side to side and scratch the coating off of the OEM cross bars. I did order these in a pinch as I was pressed for time & my original pick was out of stock so it is what it is. Very nice carrier for the price, but I'd recommend only if you've got square bars.

4 on canoe rack only because of supplied lower bracket for cross member attachment.