# 1
Stabilizer Jack - 6-1/4" Drop Leg Travel - 18" - 650 lbs - Qty 1
I purchased this jack for my 2010 Escapade Elite trailer. I finally installed it yesterday. After a quick and minor modification, it fits great and funcltions like a charm. I highly recommend this product to other MC trailer owners. Thanks, etrailer.com for the quality and price!
I needed to replace the tongue jack on my ATV wagon, but only needed one! etrailer is the only place where I could buy a single jack, and not be forced to buy a set of two or four. I ordered it, and it was at my door two days later! Great service and support, and just what I needed and nothing more! Looks great,and gives my wagon the support it needs!
# 2
Stabilizer Jacks - 6-1/4" Drop Leg Travel - 18" - 650 lbs - Qty 2
Easy to install both in under an hour. Provide good stability to small (boat) trailer when deployed. I can see the paint/powder will be as durable as they were as simple to install
Bought these for my cargo trailer. Did not get around to installing them for several months. When I finally unpacked them, the “foot” of one came off while I was unwrapping them. I had to drill holes and add a few screws to reattach. There was no damage to the box. They still serve their purpose, just disappointing.
# 3
Electric Jack w/ Footplate - Drop Leg - A-Frame - 25-1/8" Lift - 3,500 lbs - White
Received the jack in record time. Easy to switch out the old jack and install new one. Works like I hoped it would. Very happy. Thanks
Great jack, great company to do business with, easy to install, great price, will definitely buy from them again
# 4
Bulldog Powered Drive Trailer Jack - Drop Leg - A-Frame - 22" Lift - 3,500 lbs - Black
Excellent Jack. Slow moving but that is due to high torque. Well made, attractive design. Highly recommended! Solved the problem of busting my knuckles on the propane tanks while cranking the old jack.
Great jack. Just what I needed to allow my tailgate to open while hooked up to my travel trailer
# 5
Scissor Stabilizer Jack - 18-3/4" Travel - 2,500 lbs - Qty 1
Excellent product and service. I love all the videos and you give exact measurements on a lot of your products. Never had a problem with Etrailer.
They went on a custom made trailer build that’s not yet in service. Seem to function as advertised.
# 6
Fulton Drop-Leg Stabilizer Jack with Mounting Channel - Weld-On - 28" Leg - 13" Bracket -
Beautifully made and a solid drop leg. Do I need to say more? You get what you pay for.
Product was exactly what I was looking for. Only issue is the one square latch pin is missing.
# 7
Ultra-Fab Economy 5th Wheel King Pin Tripod Stabilizer - Steel - 31" to 54" - 5,000 lbs
My order arrived soaking wet box torn up and mashed. Light switch in side fox was destroyed by king pin stand. Not sure why anyone would place a fragile items in with heavy steel components.
Made in the USA, decent effective range, quality construction. What more could someone want? That said, this is heavy so eTrailer shipped it via UPS. UPS destroyed the package, taped it up, and then proceeded to destroy it again. Luckily, I was only missing one small piece of hardware that is easily sourced locally. Keep that in mind if UPS destroys packages in your area.
# 8
Ultra-Fab Ultra Scissor Jack - 24" Lift - 6,500 lbs
Installed easily and they function as designed as well. They look cleaner than the factory stabilizers as well. I also like that they use a 3/4" socket to go adjust and not a special tool like other brands.
Replacement jack fit and worked perfectly Fast delivery
# 9
Leveling Scissor Jack - 24" Lift - 5,000 lbs
Much better jack than the one that came with the tow trailer. This 70 year old woman had no difficulties installing it. One year later still works great!
I alwys have the best service with etrailer. Been using them for years.
# 10
Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors - 30" Lift - 6,000 lbs
Finally got around to installing my PT II Stabilizers 30" front and rear of our 26' Surveyor. Pre - assembled them to make sure they went together ok. Luckily I had two sources for power front & rear which made wiring easy, I used a Buss block to make all positive connections, grounds straight to frame, soldered all connections and heat srinked to seal. Using the 3/8" self tappers was fun.Well got it all together and all works well makes trailer very stable, don't have to worry about scissor jacks collapsing anymore.
It looks like a great product am anxious to install them. I have a symbol of them in my garage and I have one with a really crooked foot. The bolt hole on the retracting arm was drilled in the wrong place so it is totally crooked, not a deal breaker though. I’m sure the are more than Adequate
# 11
Lippert High-Speed Power Stabilizer Jack - White Switch Kit - 30" Lift
Easy to install and functioned perfectly. Customer has been utilizing it for a year and still raves about it. Thank you
Pros: Works better than I anticipated. Looks great and has better ground clearance than the stock scissor-jack stabilizers. Cons: Installation instructions/documentation weak or non-existent. If all of the instructions, wiring diagrams and documentation were in one place on the web page under a separate tab rather than having to dig through the reviews and the Q & A’s, I would have given this a 5 star rating. I ordered the LCI Power Stabilizer Jacks with the white switch Kit (LC369774) because I wanted the switches mounted in the camper wall so they would be better protected than if they were mounted in the flimsy fender skirts of my camper. I also needed the bolt-on spacer kit (LC673594) for both the front and rear jacks to clear a propane line that runs along the length of the frame. Installation was relatively easy, although there are NO instructions on how to install the spacers kits; the video on etrailer.com was no help whatsoever with the installation. I bolted the jack mount brackets to the shorter side of the spacers using carriage bolts and flange nuts; the slotted holes in the spacers accepted the carriage bolts, aligned perfectly with the holes in the jack mounts, and allowed me to install them without having to try to fit a wrench inside. Then it was just a matter of drilling holes in the frame at the appropriate spacing for flange bolts/nuts through the slotted holes on the end of spacers. I was very pleased with how the switches and the switch compartments looked once installed. Again, though, it took lots of digging to find the wiring diagram and then the matrix for the switch wire colors, because the wires on the white switch are colored differently than the black switch that all of the diagrams show. Also, it states on the jack installation instruction sheet that the power must be a minimum of 10 gauge wire (AWG-10), but nowhere on the wiring diagram does it say anything about that. AWG-10 is a MUST because of the way current drops over a distance. In the case of my camper, it is a 30 foot run which requires that gauge of wire for 20 AMPs.
# 12
Lippert Electric Trailer Jack with Footplate - A-Frame - 18" Lift - 3,500 lbs - Black
The bolt pattern matched my trailer so it was very easy. No skill needed. I soldered a connection on and hooked it directly into the battery. I had to drill a hole for my foot extension. So far so good. 23 foot travel trailer.
As always a big help in getting what I need, and wanted. Good tec help, fast service. Already installed.
# 13
Lippert Smart Jack Electric Trailer Jack w/ Footplate - A-Frame - 22-1/2" Lift - 3.5K - Black
I purchased this jack because it is the exact same model as the jack installed on the trailer at the factory. I have attached a photo of the one I removed. I had the trailer power washed and the spray damaged the membrane that covered the three switches that operate the jack. The resulting exposure damaged the switches which could not be repaired. Not the best design in my opinion.
ordered overnight and got in a timely fashion!!!
# 14
Lippert Power Stance Electric Trailer Jack with Footplate - A-Frame - 18" Lift - 3,500 lbs
The product works as designed. Easy to install and I have used it approximately 20 times in the last year. The storage for the 7 pin connector and safety chains are a great option. Keeps things nice and tidy when unhooked. I highly recommend this Jack.
The service and shipping were beyond my expectation. I will be installing this to replace my original jack that failed soon. Thanks for the help and quick service !!!
# 15
Stromberg Carlson Electric Trailer Jack - Drop Leg - A-Frame - 23" Lift - 5,000 lbs - Black
Overall, it is a great product. I really like not having to crank the trailer tongue up and down by hand and it works very well. One suggestion for Stromberg-Carlson: Turn the motor/gear assembly so it faces away from the front of the trailer, but leave the light to shine on the hitch assembly, etc. The tongue of my trailer is short enough that the hatch on my Traverse cannot be opened when the trailer is hitched. Might apply to a pick up tailgate, too.
I was extremely impressed with the recent technical and customer support from etrailer. Over the weekend, they answered my questions to select the appropriate replacement electric jack for my Airstream. Also, when there was a shipping delay (not etrailer’s fault), Rose provided prompt responses and professional support. I will continue to use etrailer for my RV needs.
# 16
Bulldog Powered Drive Trailer Jack - Drop Leg - A-Frame - 22" Lift - 4,000 lbs - Black
Replaced stock Air Stream power jack which started making grinding noises. New 4,000 pound jack easy install and works fine. Using it to lift 25ft trailer and 2500hd Silverado to attach anti-sway bars. Had to mount it sideways due to propane tank cover, but it works great. Had one of these on a larger trailer that a hurricane destroyed. Nice unit and easy install.
Overall the product does exactly what it's intended for and works well. I however assumed that this would be a simple R&R for my camper and did very little installation research other that the video provided on etrailer' s website Sadly it did not fit. Not at all. I didn't take into account that have a double framed hitch toyhauler. The baseplate on the factory leg was a TRIANGLE.....this unit was ROUND. Also the primary shaft was thicker than stock and would not drop down into place I know modifying is frowned upon, but I found that ALL powered hitch legs I found have round mounting plates and it's not mentioned the leg tube is thicker than OEM? Since NOT having a power lift wasn't an option for this camper application...too heavy in the front when ATVS loaded to lift for setting the equalizer hitch tension bars, I proceeded to modify by cutting the rear rounded mounting base ... square. Took off about 1/2 inch. Then I took my metal Dremel sanding bit and increased the hitch leg hole diameter slightly. Took about 1 hr. Dropped it in. Wired it. Tested it. All good. If you can't post this I understand, but take note that some of your website descriptions may need to be enhanced. Thanks!
What our customers are saying:
"You folks are fast. Thank you very much."