# 1
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
I installed this on my 2015 Honda Accord for the purpose of pulling my small aluminum fishing boat and trailer. Works great!
Drawbar looks great and will be using in next two days. Thanks!
# 2
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
Longer stinger let me drop the tailgate on my Tacoma with trailer attached. Replaced a similar but shorter Curt hitch and both are very substantial and well made for the weight of my trailer.
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
# 3
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Good product.. Only wish it came with the pin to hold it into the hitch
Ball mount works perfect with my hitch. Great product!
# 4
Curt Class II Drawbar - 5" Rise - 9-5/8" Long - 3,500 lbs
I am an infrequent trailer user, but getting my daughter home from college was necessary in March. This drawbar fits my hitch and utility trailer well, did exactly what it is supposed to do, and was the last thing to be concerned about right then. I have a '11 Mini Countryman S with a Class II receiver from Mini Fini, (which cost twice as much as a Curt) where the hole is flush with the fake grille near the bottom of the bumper cover, so I needed the long bar to reach out past the bumper. The Curt receiver for that car hangs visible underneath the bumper (ugly), which also increases the lever arm on the receiver beam and would have needed an even taller rise. (Curt take note!) All just part of the kit to create an occasional 1 ton pickup out of my Mini, leaving the "bed" at home most of the time.
Fits perfectly. I just wish you would’ve sent a pin with it because I had to go chase that down and get an aftermarket one at Ace Hardware.
# 5
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Good product.. Only wish it came with the pin to hold it into the hitch
Ball mount works perfect with my hitch. Great product!
# 6
Curt Class III Ball Mount with 1-7/8" Ball - 4" Drop - 3,500 lbs
Perfect fit on my car. I was worried I was going to have a hard time getting the right hitch and wiring harness, but thanks to etrailer, I didn't have a single hiccup. I was worried about not getting it in time for my cross country journey in which I will be needing to pull a small trailer. I ordered the hitch with only about a week before I'm supposed to start my drive and got everything within just a few days! Great all around. Really took the guesswork out of all of this. Thank you guys
I have purchased my trailer hitch, ball mount and hitch locks for my 2017 Dodge Journey. The service and products from this company have been top notch and I plan on using them in the future. Thanks again for a service that is increasingly hard to come by these days.
# 7
MaxxTow Ball Mount w/ 2" Accessory Receiver - 2" Hitches - 2-1/4" Drop - 5,000 lbs
Heavy duty , very good quality.
# 8
Curt Ball Mount for 2" Hitches - 8" Rise, 9-1/4" Drop - 14" Long - 5K
Perfect fit on my car. I was worried I was going to have a hard time getting the right hitch and wiring harness, but thanks to etrailer, I didn't have a single hiccup. I was worried about not getting it in time for my cross country journey in which I will be needing to pull a small trailer. I ordered the hitch with only about a week before I'm supposed to start my drive and got everything within just a few days! Great all around. Really took the guesswork out of all of this. Thank you guys
I have purchased my trailer hitch, ball mount and hitch locks for my 2017 Dodge Journey. The service and products from this company have been top notch and I plan on using them in the future. Thanks again for a service that is increasingly hard to come by these days.
# 9
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 9-3/8" Long - 3,500 lbs
I wasn't sure what type of ball mount I needed for my new Mazda CX-9, so I had to call a representative. The first time I called, the very knowledgeable gentlemen told me exactly how to measure my SUV to figure out the drop I needed. I called back the next day and talked to a lady who helped me figure out exactly what I needed. This is my second purchase from etrailer. The first was a hitch for my old Honda Odyssey, which was also a great experience. The employees are so helpful, the video tutorials on the web site are fantastic and the prices are great. etrailer.com is the first place I go to look for trailer and towing supplies!
I needed to tow a trailer with a 2" ball. My original ball mount has a 1 7/8" ball installed. I had previously tried to change a ball on a hitch and destroyed the nut and damaged the underside of the ball mount. The lock washer had done a great job in keeping the nut from coming off. I dreaded trying to remove my 1 7/8" ball to install a new one that I would only use once. I decided to buy a new ball mount and mount the new 2" ball. This ball mount is so inexpensive that I realized I could have both ball sizes permanently mounted for use in either ball size.
# 10
Curt Dual Length Ball Mount for 2" Hitches - 1" Rise, 2-3/8" Drop - 7,500 lbs
Quality product. I needed a longer mount for my side by side and this will work well.
# 11
etrailer 2-3/4" Rise or 4" Drop Ball Mount Kit - 7,500 lbs
Very good deal!!! And the quality is superb.
Nice kit for the money meets my trailer pulling needs.
# 12
Curt Channel Style Adjustable Ballmount - 5-1/4" Rise, 6-3/4" Drop - 6,000 lbs
New GMC AT4 required a new ball mount and this one fit all the requirements for the truck and new multi-pro tailgate. With the AT4, I needed more drop and a longer shank (12" hole) for the tailgate to not hit my trailer jack stand; plus, the multiple drop adjustments will make changing trailers a snap. Great product from Curt and great service from etrailer (as usual).
Very nice hitch and great service
# 13
Curt Ball Mount - 6" Rise, 8" Drop - 11-1/2" Long - 5,000 lbs
Perfect fit on my car. I was worried I was going to have a hard time getting the right hitch and wiring harness, but thanks to etrailer, I didn't have a single hiccup. I was worried about not getting it in time for my cross country journey in which I will be needing to pull a small trailer. I ordered the hitch with only about a week before I'm supposed to start my drive and got everything within just a few days! Great all around. Really took the guesswork out of all of this. Thank you guys
I have purchased my trailer hitch, ball mount and hitch locks for my 2017 Dodge Journey. The service and products from this company have been top notch and I plan on using them in the future. Thanks again for a service that is increasingly hard to come by these days.
# 14
Curt Class II Drawbar - 3/4" Rise, 1-1/4" Drop - 9-3/4" Long - 3,500 lbs
This draw bar in perfect for my John Deere X738 tractor. What I like about it is the ¾” rise it keep the draw bar height at about the same as the factory frame so the attachments height remain level. Thanks for the great product.
Well made, quality product.
# 15
Draw-Tite Ball Mount - 9-3/4" Rise, 11" Drop - 9" Long - 3,500 to 5,000 lbs
Good product.. Only wish it came with the pin to hold it into the hitch
Ball mount works perfect with my hitch. Great product!
# 16
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 9-1/4" Long - 7,500 lbs
Perfect fit on my car. I was worried I was going to have a hard time getting the right hitch and wiring harness, but thanks to etrailer, I didn't have a single hiccup. I was worried about not getting it in time for my cross country journey in which I will be needing to pull a small trailer. I ordered the hitch with only about a week before I'm supposed to start my drive and got everything within just a few days! Great all around. Really took the guesswork out of all of this. Thank you guys
I have purchased my trailer hitch, ball mount and hitch locks for my 2017 Dodge Journey. The service and products from this company have been top notch and I plan on using them in the future. Thanks again for a service that is increasingly hard to come by these days.
# 17
Curt Vertical 2" to Fixed Ball Mount - 12-3/8" Long, 2-1/4" Rise
Purchased for a Dodge Journey with vertical mount hitch. Waited 5 months to get one from Chrysler and finally gave up found this one online. Sturdy design and does what I need it to. My only complaint is there is no recessed slot for the hitch ball to screw in tightly.
Tried to get this from the Dodge who put on the hitch. After six weeks of waiting I called you and got it in two days. Thanks.
# 18
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
I am using the hitch for a car dolly and a bike rack. The fit is a little loose for the bike rackmI'll see it really works when get on the road.
Quality is excellent. However, it did not work so I am not sure what to do with it. I thought I could use the top hitch for a Bike rack and pull a utility trailer with other toys. The trailer is too close to make a turn so good try but not able to use it. Thank you for asking. I did not open the box for a while because I was having the trailer worked on so assumed I waited too long to return.
# 19
Curt Class II Euro Style Drawbar with 1-7/8" Ball - 6-5/8" Rise - 3,500 lbs
Great Product! After installing a Curt (C11184) Hitch on my '08 BMW 135i convertible, I needed a drawbar and ball. I really liked the elegant design and one piece simplicity that this one has. It is very sturdy and the dimension measurements were accurate. The whole reason I got it was to trailer my new (old) wood boat home from the barn I found it in. Once the hitch was on and the (56146KIT) Wiring kit was installed. This drawbar slid right in. Thanks to the accurate measurements the trailer sat at the perfect height the first time.
works great
# 20
Curt Class III Drawbar - 2" Rise - 4" Drop - 13" Long - 7,500 lbs
Haven't used it yet. I bought it because of CURT's quality. It was beat up in shipping though.
This 13" drawbar keeps the tailgate off the trailer jack. Being that long also keeps it I storage immediately after I disconnect the trailer. No need for a locking pin.
What our customers are saying:
"very easy to shop"