Most Popular Draw-Tite for 2007 Saturn Vue

Very nicely built and easy to install.

Strong and seems to be well made and well finished. One-inch ball mounting hole. I used this for a Curt hitch mounted on a 2014 Forester and pulls a small Harbor Freight trailer. Perfect height and trailer is level. Warning - don't get their hitch pin, it does not have a hole for a cotter pin, only a weak clip that I would not trust.

Solid, well-engineered, and value-priced

I hooked up the draw bar today for the first time to the trailer that I built and the hitch I installed. The draw bar uses a cotter pin that slides on the bolt rather than going through a hole to mount the bar to the hitch. I have never used a sliding on pin in anything - I've only used those that go through a small hole matching the pin. This includes my farm tractor and other tools. I hope it is secure because it does slide on easily. The bar itself appears nice and strong.

Easy to use and haven't had any trouble towing my small trailer with motorcycle on board. Def recommend.

This part came with the trailer hitch I purchased. It was very easy to transfer the ball from my 2" hitch and voila I am now ready to haul my trailer.

The welding splatter found its way to the hitch pin hole and it took me some time with a Dremel to clean it out so the hitch pin would slide in.

Each edge of the hitch receiver shipping carton was pierced by mounting brackets, but no damage fortunately. Consider adding another layer of cardboard padding?

To be honest, I use it upside down. I needed a hitch with rise, but none were available at time of purchase, and yours, inverted, works perfectly! The welds are regularly checked and remain all secure. It's a good hitch.

Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.

I got this to Flat Tow my Jeep in the near future. I needed the 5" rise and now the tow bar is almost parallel to the ground. Although the etrailer.com site said this was an economy unit, I am very impressed with the look and feel of the unit. It handles up to 12,000lbs! Nothing economy about it except the very fair price!!! The pictures and video, along with the measurements helped ensure the fit would be perfect and it is! I got a 1" rise ball good for 6000lbs to make the tow bar perfectly parallel. Thanks etrailer I will always shop etrailer first when looking for this type of equipment.

I bought a new truck with twice the towing capacity of my SUV. I needed a 6" drop instead of my original 3" drop, so I bought one with a 12,000 capacity. Very nice.

Seems to work as expected. Installs easily. I had a CURT drawbar for my other vehicle but they didn't have one in the Drop I need for my new car. I prefer the lock pin on that CURT model, it's feels heavier duty, than this so I just swapped them out.

Exactly what I needed. I bought this Mercury Mariner used and it had factory installed hitch with a 1 1/4 receiver. I needed a drawbar with a substantial drop to tow my utility trailer somewhat level. Local shops had lots of 2 inch drawbars with drops but no 1 1/4 and I was even told that they weren't made and I would have to use a 1 1/4-2 inch receiver adapter do get what I wanted. You folks had what I needed and it arrived quickly. I should have looked here first.

works well brings the trailer tongue up to level. I have it on an EV so the raddle is annoying, because I just keep on forgetting to buy a anti rattler.

This is very sturdy hitch. It is made of solid steel, not tubing. It will be used on my Mazda RX-3 to tow my car dolly to the RV lot where I will swap everything around and the car will end up on the dolly behind my RV.

fit perfect.

Everything was perfect.! Nice paint, package, and fast shipping.! Im satisfied.!

The Ball Mount was noisy upon hitting bumps, uneven road, etc. I have since gone to a shorter, dampened ball mount but I have to remove the spare tire when I use it!!! Ruben

The receiver is exactly what I was looking for. Put it on a 2016 chevy traverse and it is the right length for pulling a trailer. Looked at 6 1/2 inch, too short. Quality is good also. I give it 4 stars.