Most Popular 9000 Lbs Line Pull for 2005 Honda Pilot

I plan on using this to assist me in backing my travel trailer into a small side yard next to my house and my neighbor's fence. Backing it into this small area has been extremely nerve wracking as my home air conditioner unit is close to the house and trailer. Now I will have the luxury of making sure nothing is damaged. and better yet the front hitch will be hidden under the car and out of the way.

This my third front hitch and they work great for my purpose. I am a pilot car for oversized loads this works great for front sign and as a carrier for the high pole each one has fitted properly and work great Thanks Ronnie

Curtis "Front Mount Trailer Hitch" ordered for 2017 Nissan Frontier (Crew Cab-4x4). Excellent product quality, quick delivery, and follow up customer service. Hitch as advertised. As several other reviewers have mentioned, the front mount trailer hitch holes do not line up exactly with the truck frame holes so a bit of manhandling is required to get the bolts installed properly. I needed to be able to push my boat/trailer up my driveway, around a corner, and into the garage. Works better than I expected; very satisfied.

I got this Class II front hitch for my 2016 Nissan Frontier to help me back a small trailer into a tight space. It arrived in good condition with complete instructions and good quality hardware. When I tried to bolt the hitch on, I found the 1/4" plate brackets were 3/8" too narrow to match up with the holes in the Frontier's frame. Michelle at ETrailer gave me some good advice on how to spread the brackets with a hydraulic jack and bingo, the hitch fits and looks great! BTW, the ground clearance is still around 9 1/2".

Easy to install. The only drawback I see is on my 2022 Pro4x model I had to remove the red tow hooks and silver front skid plate because the hitch takes their place.

Haven’t had a chance to use the front hitch on our Nissan Frontier year but the installation was quick and easy. I was all set to knock the installation out in 20 minutes until one of the split lock washers failed and had to be replaced out of my spare stock. Also an additional note: the hitch showed up heavily scratched despite the packaging having been in good condition. Maybe some more careful handling at the warehouse is in order.

The hitch arrived within six days of my order despite not requesting quicker shipping - a delightful surprise. Installation was quick and easy; just four 12mm bolts. It helps to either have an assistant or a jack handy to place the hitch while installing the bolts / tow hooks. Overall, though, be ready for a little more work. A hole needs to be cut into the skid plate in order to allow oil filter changes without removing the hitch each time. I've read that the bolts that hold the hitch to the frame shouldn't be removed and re-torqued frequently. You could, I guess leave the skid plate off, but I wouldn't risk it. Be sure you have a means to cut the skid plate. They recommend a round hole and I assume use a 4-inch hole saw. I used a pneumatic reciprocating saw with 3/8-inch driller corner pilot holes to make a 4-1/2 inch by 4-1/2 inch hole directly under the filter. Be sure to file down the sharp edges of the new hole too. The service guys' knuckles will appreciate that. The hitch itself is a quality part, arrived in pristine shape and looks great on the truck. You will need a hitch extension since it is recessed behind the front of the truck a bit.

Shipping was fast and packaged good with no scratches. I modified my 2010 Tundra skid pan for oil filter changes before mounting. Replaced all 4 OEM tow ring bolts using anti-seize with new longer M12-1.25 X 40MM class 10.9 zinc finished hex cap screws along with new M12 X 24MM OD HARD WASHERS and torqued all 4 to 79 ft/lbs. Mounted new Thule EasyFold XT 2 Hitch Bike Rack and it fits in front without using the hitch extension. All went together as planned and can now take E-Bikes with us while pulling our camper. We are happy campers!

First your tech assistance was great, was able to verify this is the right hitch to fit my truck, you really don't want to crawl under a truck and find out its the wrong configuration. Second, the shipping was fast, I will rate that as (four stars). Third and most important, the hitch was the easiest to install, it took me approx. 40 min. Thanks guys. We will buying more products from you. Attached before and after photos, very clean installation.

I bought this after years of struggling to get a race trailer in the backyard. When I decided to move it about 12 feet to the right, I knew there was no way my F350 4X4 crew-cab could make the tight turns that would be required. After being able to position it on the first try, I realized I should have bought it 20 years ago. The installation took two tries. Not sure if it because I’m 66 or trying to do it by myself. The key for me was to hook a couple of straps to it, unbolt it, and then put the bumper on the engine compartment. The first attempt was by trying to do everything from the backside. Once I removed the bumper completely, I was able to do everything from the from, so I was not completely blind in installing the two side bolts. The straps not only made it easier to reinstall it, they were useful in pulling up on side to level it. I will be buying my son one for his 2016 F150 4X4

I ordered these two, front and rear for a 1990 GEO Tracker 4 wheel drive that I am rebuilding. I believed they would fit, I finally got around to mounting them and they don't fit, to large. I think I have had them to long to return them.

Just what I was looking for. Thank you.

It was not as easy yo install as the video seems to suggest. I had planned to do it myself with the truck on ramps, but had to get someone with a lift to do it. Once the plates were mounted the main part didn't line up just right and it took more pressure than I could apply while lying on my back. Other than that it is great. Very strong and just what I needed.Thanks.

The hitch came packaged in a double box. The outer box had some damage but the hitch did not. I read the instructions, making sure i had the correct tools, and jacked my truck up. The install took three hours as i was layiing on my back with simple hand tools. The parts all fit and i am happy with the outcome. Good price, simple instructions, good fit.

I have had this hitch installed for just over a year now on my '99 2-door Tahoe. The install was pretty straight forward, and the hitch itself has held up quite well through a year's worth of abuse. I use it to run my bike rack out the front; the receiver protrudes just below the factory front bumper, maximizing ground clearance when adding length to the front of the vehicle. And as you can see, the kit comes with two sets of hardware in case you want to maintain the factory tow hooks like I have.

Great products, great prices, fast shipping and a great company to do business with. Easy install, and it took longer to trim the air dam than installing the hitch.

Install went perfectly. It all bolted up just how the instructions said it would. The hardest part was navigating your tools in the tight spaces. Having the deep sockets as suggested is definitely worth it. I was also able to utilize a cordless impact wrench and it helped a ton. This will work great for our bike rack.

Great front receiver hitch for my Chevy Silverado 2500 HD. Everything fit using OE bolts and nuts. Only the plastic trim had to be cut out to fit receiver. I had dealer do it, but would have done it myself when I was younger. etrailer is easy to order from and has good customer service.

2019 Honda Ridgeline RTL-E. Installed it myself but a helper would have made it easier. Instruction say to remove and discard the lower engine shroud before mounting. I chose to do surgery on the shroud to fit the attachment points and put it back in. This made the install harder (less finger room) but the result in very nice. I measured clearance before and after at the lowest part of the engine. Putting this on reduced overall clearance 1 inch. It changed angle of attack significantly. Here's what you should think about...Is this a vehicle for serious 4 wheeling in? Then don't do this. And buy a different truck with greater ground clearance. If, like me, you pull a small trailer on paved and gravel roads, and you want to put bikes on the front, this will work great. See pictures attached.

Love my Ridgeline. But the only hard point in the front is buried deep under the engine. This provides three rescue points and a way to mount a winch or whatever with a 2” hitch mount. Here is the good and bad. Etrailer.com was perfect. Fast shipping, good communication.five stars. The quality and value of the hitch is top notch. Holes lined up perfectly. All hardware was provided and high quality. Now the less than ideal. The hardest part of the installation was getting the rivnuts set. They wanted to spin in the holes. I had to rig a little tool out of a long eyebolt, screw it into the rivnut and run a nut up against the mount with a fair amount of muscle to expand the anchor. The other quip I have is that the hitch is very low. If I I mount a bike rack or something I’ll have to add a riser. The hitch comes out under the bumper and Honda didn’t go for maximum clearance. Ideally a hitch would come out though the bumper at a more appropriate height. But that would require a great deal of modification to the truck. I can’t fault the seller or the hitch manufacturer for these issues. Rivnuts are just work to set without the specialized tool and Honda gave us a pretty low front end. Moreover I am happy with the upgrade and feel better having a way to mount loads up front or attach a rescue strap.

I bought this receiver to add front mounted 'accessories' on my 2007 Jeep Wrangler Unlimited Sahara. I plan on using this to add an extra bicycle rack, a cargo basket, a receiver mounted winch or other 'accessories' needed for my Jeep when I take my family camping. It will also be useful for "front launching" a boat or parking a trailer in tight spots. It took me about an hour to install, although I had already previously removed the lower wind deflector cowling, so did not have to spend time removing it or cutting it for a finished look. Detaching and moving the top trim panel between the grill and the bumper is a must to facilitate the installation. The receiver fits pretty close, although you do have to manipulate it to get the holes to line up with the frame. Follow the instructions and do not tighten any of the bolts until you get it lined up and all the bolts in loosely, then torque it down. As noted in the instruction sheet, the driver's side of the receiver does not sit flush against the frame, there is about a 1/4" to 5/8" gap. The instructions say to use the extra split washers (in the kit) as filler, but they would just rattle around loose in there and provide any benefit, so I omitted them. Once tightened down, the receiver tube was not parallel to the ground, it is slightly higher in the front, sloping towards the rear. It is not off enough to affect my intended use, but may be bothersome to those with type 'A' attention to detail. Overall a good product that will add a lot of flexibility to my Jeep~

I received my front hitch for 2015 Jeep Unlimited right on time. Install Time total with clean up was about 5 hours. I have attached some pictures. Hitch is very well built. This is exactly what I wanted. Thank you etrailer.

I chose Draw-tite because they are built very well and this one is no different. The welds are done well and I have no fear that this product will serve me well. The install wasnt to bad for a DIY type like me and the fit was excellent, only took a few hours. Knowing that I can now be pulled out of a bad situation or pull someone else out is comforting with the help of a hitch mounted winch. The Price was right and etrailer shipped it out fast although packing could use a smaller box . Oh yeah, UPS sure tested the toughness of this receiver ! . Great product and great service from etrailer

im very satisfied with my front receiver. ive used it as a recovery point,to move trailers, and as a mount for bike rack and cargo holder. if i had a winch platethat would be very handy too. etrailerhad a fair price, quick shipping, and overall great customer service. i would use them again andrecommend to a friend as well.

I bought this hitch for my 2024 Wrangler. The construction and finish are exceptional. The printed instructions should be rewritten since they are rather vague. The online instructions are fine and will get you in the right direction. The only negative thing that I can say is that it will be difficult to mount a lock since the air dam is way too close to the pin hole.

Fits perfect and works just as I needed it to. I use it for my SnowSport plow set-up on a 2022 Gladiator Sport Max Tow. I’ve been using front receivers for this same plow for the last 24 years. It’s been used on 5 different trucks and this front receiver mount plow is the BEST. *** When installing on a Gladiator(possibly the Wrangler as well), the front plastic trim below the bumper needs to be cut for receiver clearance. I wanted a tight and “factory looking” install, so I took my time with a vibrating cutter and very sharp utility knife. After trying to put it back in place, the hole is not just square, it’s shaped more like. “T”. I suggest you make small adjustments/cuts as you go forward. It may take several times fitting and cutting to get it right and tight, but in the end it does look like it came that way from JEEP. On the Max Tow package, there is also a metal skid plate that does not get reinstalled. Unfortunately that piece is where the back of the plastic fascia mounts. I ended up securing it with some long heavy-duty zip-ties and it’s worked well for a year now. Just an FYI for those installing the same receiver on their same vehicle.

I purchased this front receiver hitch for my 2010 Ford E350 RV to use for a utility basket, launch a 16' boat and now also for a motorcycle carrier. The quality is excellent and full weight rating, one year later and the finish is perfect. Installation was exactly as stated in the directions and the modifications were minor, requiring existing holes in the frame forward of any critical mounts drilled larger and the plastic under the front bumper where a tag goes has to be cut slightly to allow for receiver. The directions called for removal of under carriage splash guard but I was able to trim and reinstall. I am perfectly happy with the purchase. When hauling a motorcycle on the front the RV rides so much smoother and better planted on the road without being overloaded.

This fit my Ford 2023 E-450 (cutaway) perfectly. I had measured the frame of previous year E-450’s and didn’t see any difference so I gambled and ordered the 65053 which fit. Installation was straight forward with modification and fitting of the splash guard taking 50% of the time. Fit and finish was good except at the front of the receiver itself. Unfortunately that’s the only two inches of the whole hitch that show and had weld splatter and sharp bits under the paint. This took a bit of filling to smooth out which I then repainted. Attached are photos installed on my 2023 E-450.

After struggling with the answering menu, Steve Z. was instrumental in locating a hitch to fit my van which was not specifically identified in any data search. Weird year, 2005, of popular Chevy Express van, my luck! Using manufacturers dimensions I purchased #31016 on 12/21 and it arrived on 12/24. It's a very well built, USA built, unit. It arrived rapidly, but was missing half of the mounting hardware. The remainder of the hardware was rolling around in the box. Zip lock baggie ripped apart spilling them. I used a hydraulic jack to elevate hitch into place, and an additional jack to push the drill up to drill the 6 mounting holes necessary. No factory hole alignment. All the nuts for the bolts were lost in transit, but by a Christmas day miracle, I found 2 metric nuts to fit supplied bolts that survived the delivery. I will acquire, and install remaining missing 4 tomorrow. The installation went smooth and easy using this technique. It took around 3 hours with much of the time searching for hardware.' Thanks Steve Z. and etrailer. .

The product works great. However, I was told that this front hitch receiver would bolt to existing holes on my 98 Four winds RV. That was not true, so installation was double the cost of what was estimated by the shop I took it to.

Great customer service and product.

The quality and fit is exceptional. So much so that this is the third hitch assembly I've purchased and installed. This one was for my brother in-laws 1999 F350. I also put a 10k winch on a slider that works perfectly with this assembly. Other vehicles I purchased and installed assemblies on are a 2011 F350 and a 2016 Class C motorhome. Very happy.

Quality hitch and the excellent service all the way around I'm used to getting from etrailer over the years. Installed on my 2016 Sierra Denali 2500HD, note instructions say on first line down that it does not fit the Denali trim due to extensive fascia cutting required; actually it was quite simple with the aid of a 4-1/2" cutoff disk and a sawzall. Installation is much easier with two people. See attached pics for actual material removed, note the lower fascia need not be cut for the hitch to fit through the hole. Maybe more work to install than the Curt hitch, but well worth the additional ground clearance.

Excellent well built receiver. The instructions however are a little misleading. The instructions refer to “Trimming the Facia” which sounds like a simple procedure when you actually must saw a square hole in the steel bumper. It takes some effort and know how. I wouldn’t attempt to install it if I didn’t have the proper tools and the ability to make things fit that don’t want to fit. Ask if I’d do it again? Most definitely.

This receiver hitch fit my 2015 Ram 2500 fine, and looks good. However, Draw-tite quality control must be a bit lax, as now that I tried to use it, I find the hitchpin holes are not the same size and even a standard pin cannot go through both holes (so as is, I cannot use the now-mounted hitch). I am going to have to bore out the hole(s) to the correct size for a locking pin, to mount the hitch-mount winch I intended to use in my dump trailer and my truck. In addition to being the wrong (or mismatched) holes, the location of the holes is right next to a beefy weld that will make securing (whether by locking or non-locking hitchpin) difficult. I cannot justify removing the receiver after all the work it took to install, but definitely cannot give this a good review. I recommend test-fitting your pin(s), tow balls, winches on it before you waste time installing. However, as always, etrailer.com rocks!

Was sad to see the powder coating chipped off the tow bar as soon as I opened the box . I can hit it with paint but kinda stinks , have not installed the bumpers yet

Installed on the front of a 2008 GMC 4x4 Sierra. Primarily utilized for a hitch mount snow plow (DK2). Installed without any modifications - works good with the plow. * The hitch sits low to the ground (stock suspension). I installed a 2" leveling kit from RC and that helped with clearance. I am satisfied with the quality of the product - will purchase again from Curt for my Durango

I have had the front receiver hitch installed on my 1996 Suburban for about a year now. I have a 12000 lb winch installed using that receiver hitch. I have gotten stuck twice and had to use the winch to extract the truck. Very glad that I have the front receiver hitch as it made putting on the winch very easy. Also useful for mounting a receiver mount bicycle rack to the front as well.