Most Popular Fixed Fifth Wheel for 2000 Chevrolet Silverado

I installed this system in my classic square body Silverado after installing the Turnover Ball BK1400 gooseneck hitch. Both work great together and this companion installed beautifully. I tow a 40’ Cougar camper with it.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Excellent fit and finish but the packaging did not hold up well to the UPS handling. Large holes in box. However, all small parts were packed in heavy plastic and arrived with box. One item for etrailer listing, B&W notes on their assembly instructions this hitch not recommended for use with Reese Revolution or similar pin boxes. This became an issue for me and I had to contact B&W for a more expensive slider hitch base. Please note this on your product listing for future users. B&W is very responsive and helpful in dealing with their customers.

This is a very basic hitch. Very simple to install and use. However, with the head not being fully articulating, its a very noisy hitch. Plenty of rattle, clank and chucking. The chucking can be a bit alarming. It worked well enough for our small 22' 5er but since stepping up to a 34' trailer and 12,000#, I decided to upgrade to a B&W Patriot. If you're on a tight budget and have smaller lighter trailer, this will get the job done but Id have gone with a better jaw type hitch over the slide bar had I known better at first. The custom install kit for my 2013 Silverado 3500 long bed was amazing in fit. You need to be a little handy to install it but its well worth the extra few $$. The installation instructions are adequate but could be a little clearer.

installed hitch in a 2008 chevy 2500hd. other then having to take out the rear inter liners hitch installed great. just follow the directions. would recommend etrailer.com and curt hitches to anyone looking. thanks jim

The hitch arrived nicely packed in two boxes. Very easy to assemble and install on my existing bed rails. I took the RV out for a first run with the hitch, and it performed as advertised. It was a no fuss transaction and the hitch arrived on-time!

Click to Enlarge

The hitch was installed on Valley Rails which was previously installed on my 2004 Silverado 3500. The hitch fit on the rails and during the first pull performed outstanding. I pull a 41ft 5th wheel and I am impressed with the double jaw lock.

Ordered my Curt 24k 5th wheel hitch on Tuesday, received around 230 Friday, and was installed by 5pm same day ( already had the rails). I am anxious to hook up my Heartland Big Country 3650RL to my 2006 Chevrolet dually and roll down the highway. The hitch is alI i expected it to be, and it is quite heavy, but managed to get it installed by myself after reading the great installation instructions. As in other posts, slight scratches during shipping due to packing materials used by Curt, not etrailer's fault. My RV has a tongue weight of 2350 lbs, 14000 overall, and 39'6" lenghth. Expectations are high that this hitch will handle it well! Thanks for the great service

Click to Enlarge

A well put together hitch , very heavy duty easy to use and maintain.

I installed the fifth wheel installation kit and hitch last week. There was a problem with the dimension given for the front rail. Instead of 52.375" the actual measurement for my truck was 52.75". Using the 52.375" measurement left half the hole covered by the frame rail. Drilling the .125" pilot hole didn't point out the problem - it cleared the half blocked frame rail hole. My truck is a 2015 Silverado High Country 3500 HD diesel, DRW long bed with factory sprayed in bed liner, built after August 14, 2015. Overall, I'm happy with the both the hitch and the installation kit.

Installed it in a 2015 Silverado 2500 WT with an 8' bed. Very easy to install, and came 90% assembled. Right after installing the 5th wheel hitch, I drove 1,600 miles round trip to buy a 40' 5th wheel 800 miles away. Pulled it back from Kentucky to Florida with no issues, worked perfect. Great hitch

The product was as stated, but what made this experience different was the very rapid delivery of the parts and great communication. If you need anything for your truck or trailer call etrailer or go to etrailer.com for fast friendly service.

The instructions could be better but I didn't have to look for support. It took a few hours to drill and measure, bolting the hitch together and in took about 45 minutes. I got the hitch Friday morning and installed Friday afternoon, picked up my RV on Saturday. I couldn't be happier with the product. I was hearing horror stories from friends about the cost of hitches, the C16 was very affordable, installed easily and I wouldn't hesitate to order another hitch from etrailer if I need another one.

This product was easy to assembly. Very clear instructions and it took less then an hour to install. I was impressed with the packaging. The cardboard box the rails came in had steel inserts in the corners to keep the rails from breaking through. The box also had 1/8" plywood in the top and bottom for rigidity. It fit perfectly in the puck system in my Silverado. By purchasing it from "Etrailer" and installing it myself, I saved $1,600 by not having the RV Dealership install one for me. Only tools I needed was a socket wrench and a torque wrench.

I just finished installing the bed rails yesterday (bear cat) on my 2017 Chevy Silverado 3500HD and installed the Curt (C16130) hitch. I've not towed or hauled any trailers with it yet so I don't know how it will perform. I previously used a Husky (15K) hitch which I really liked. The Husky was getting old and showing signs of wear and I didn't like the clanks and squeaks. The Curt hitch went in easily though it a fewer height adjustments.....height adjustment holes are two inches apart versus 1.5 inches on the Husky. It is a stout (and heavy) hitch. I frequently put my hitch in an out and the Husky could easily be broken down into two parts....reducing the weight. The Curt appears difficult (at least so far) to break down into two parts. I did it twice and had to use a crow bar to separate the head from the legs. It's way too heavy to handle in one piece....as are most fifth wheel hitches. Maybe it loosens up after use and comes apart easier.....I hope. I assume it will provide great service and eliminate the noise and chucking and had with my old hitch.

We received the hitch and brackets packaged very well. The installation went well and pretty straight forward. We did not have our 5th wheel to set the height but took a lucky guess at 18". We picked the RV up and couldn't be happier with this hitch. Absolutely no chucking, very smooth ride. We have an uneven slope to back down to get to our RV pad and were concerned about that. With the swivel on this hitch, backed with no problem. We wouldn't settle for any other hitch if we have to ever buy another one. The RV sales and service people were very impressed with this hitch and the way it is set up with the frame brackets. Very happy customers!

Click to Enlarge

Click to Enlarge

Installed in 2017 Silverado 3500HD.

Click to Enlarge

Click to Enlarge

I installed this hitch on my 2019 Silverado 3500 HD dually diesel a year ago. We towed a Keystone cougar 366 RDS fifth wheel with it all summer and it worked flawlessly. I would recommend this hitch to anyone. It feels heavy duty and is well made. I’m also in the construction industry and understand when something is well made. It is fairly heavy but I was able to install it myself. It would be handy to have two people to remove it and install it but if you remove the head first and then the body it’s manageable.

product is great but like previous reviews that i read packaging could be very much improved . received 2 packages 1 had the head in it that was packaged very good , however the package with the leg mounts looked like it had gone thru a war zone . legs were scratched but not damaged , just put a little touch up paint on them . install was very easy , it went together with ease . fit in my 18 3500 Silverado with no issues .

Product is very well made. Glad I went with B and W Patriot Hitch. Once the bed rails were installed the rest was a breeze. Now it's time to get a 5th wheel and hit the open road. etrailer, my go-to website.

Click to Enlarge

Click to Enlarge

Buying and installing the AM3200 filth wheel hitch was one of the best thing I Have done . It has made trailering a lot more comfortable driving , very little bucking when going over bridge expansion joints and bumps in the highways. I have a few problems hooking-up with the type of trailer hitch I Have on my 5th wheel and I also have air ride on my TV. When hooking up I Let all the air pressure off my air ride system and off the hitch. Before I disconnect (raise the trailer) I put on a ratchet strap to hold the hitch from dropping down, It sounds like a lot of work but it will have. To do till I come up with a better plan. I would not go back to my other hitch, you have to excuse the pics hard to pick

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

We have the Anderson Hitch installed on our 2017 Ford SuperDuty and pull a Reflection 337RLS. We have traveled over 4,000 miles and have been extremely satisfied. The hitch allows plenty of clearance between 5th wheel, bed, and the truck cab. Hook-up and disconnect has always been easy, even with RV lots that were uneven dirt lots. I use Curt thin rubber sound dampeners (item 16900) and this provides a quiet, tight fit between the rails and hitch. Of course the light weight makes it easy to remove when not towing and less weight when you are towing. A great product for the right truck, trailer combination.

Click to Enlarge

After a lot of research I still had many questions about which hitch to install in my new 2020 Chevrolet Silverado 3500 single rear wheel with a standard (6 3/4') bed and the factory puck system. Did I need a slider as everyone suggested or would I be fine with a fixed hitch and save some weight and money in the process. I called B&W Hitches to find the exact location of the king pin receiver compared to the gooseneck opening in the truck bed so I could take an exact measurement. They were eager to assist but I couldn't get an exact number. I then called etrailer and they were extremely patient and even put on hold a couple times to try to get solid answers to my questions. Both places said the fixed hitch may work but recommended the slider. I decided to go with the fixed base hitch and in my situation I'm very happy that I did. The hitch arrived in two days in two boxes and was in great shape. I spent about 1 1/2 hours installing it and all went well. Each piece was easily handled by myself. Now for the number I could not find anywhere. With the 3710 hitch mounted in the rear most position the measurement from the center of the kingpin to the back window in my truck is 45 in. My camper is exactly 96" wide (radius 48" from kingpin center to trailer side) and the front is heavily radiused which will not allow for an absolute 90° jackknife but it comes pretty close. if your trailer nose isn't radiused or the kingpin sets back further you will not have the turning radius that I do. this fixed base hitch will not work for everybody but in my situation it did. I haven't road tested it yet but I expect that to go very well. Both B&W hitches and etrailer were extremely helpful and very professional. Hope my pictures help.

Click to Enlarge

Did lots of research and bought this one. I am very happy with this hitch. Delivery was quick and installation was a breeze. I pulled my 34 ft 14k trailer and was very happy. Reading the reviews I was a little concerned about it not being a sliding hitch and I have a 6 1/2 ft bed on my Silverado but testing it after installing I can almost jackknife without hitting window. I did install on the highest setting which proved to be too high so I lowered it by 1 set of holes. I would definitly recommend this hitch! Truck is a 2024 Silverado 3500HD Crew cab with 6 1/2 ft bed and the step tailgate. The trailer is a 2009 34 ft Hitchhiker.

box was damaged but everything in side was okay need to change rails for this A20 hitch.

After a few adjustments for my 17 Silverado the fifth wheel hitch works great. I like the fact that going down the road I don't hear no rattle or bumping around

The truck that got the install is a 2002 Ford F350 Super Duty 7.3 L Diesel dually. The Demco Recon 5th wheel hitch (DM8550043) looks like a well made, heavy duty hitch. All the welds are precise and well done. I like the single wrap around jaw with the real thick bar that backs that up. The handle that pulls out to unlock the jaw moves with ease and locks in the out position when the jaw opens. When the king pin comes in contact with the back of jaw, the jaw wraps around the king pin, the handle closes, you put in the safety pin and your ready to go RVing. I chose the Husky Custom Rails and installation kit (HT31405-686) for my install. The reason I chose these rails over the ones that etrailer had matched up for the hitch is, I had previously installed a set of Airlift Airbags and I didn't want the rail install to interfere with the airbags. It was a good choice, there was no interference at all. If I had not had the bags, I would have chose the rails and install kit that require no drilling. Drilling the holes went very fast and easy, it was torking the rear bolts down that was very difficult. There was not enough room to get a wrench of any kind around the nut. I wound up using a set of vise grips on the nut while a friend of mine torked the bolt slowly from above. All and all I'm happy with the product and I'll give another review in a year.

Click to Enlarge

Click to Enlarge

I purchased this hitch to connect to the Chevy factory prepped 5th Wheel kit for a new 2017 Chev Silverado 3500 dually. My previous truck/ hitch combo (2015 Chev Silverado 3500 single axle 6.5’ bed w/ Reese Pro Series) used industry standard rails and there was quite a bit of movement in the entire hitch assembly and king pin area resulting in significant chucking on the horrible So. Cal. freeways. The B&W hitch was one of two recommended by the professionals at etrailer. I could not be happier. The hook-up is very easy & the overall operation of the hitch is much easier & simpler than my previous hitch. The 1” thick jaw makes a secure connection to the kingpin and the overall ride has smoothed out significantly. Great product so well liked that my son found a used one for sale and snapped it up for his rig.

Click to Enlarge

Click to Enlarge

Outstanding customer service/support coupled with a great product at a great price...what more can you ask for? My hitch arrived with superb packaging and simple to follow instructions. Being super meticulous, I installed my hitch in a couple of hours. The Companion's design works fantastic with the OEM puck system in my new 2017 Silverado 3500HD Dually! Really looking forward to hooking up my new 5th wheel and hitting the road! If you are in the market for a new hitch, definitely consider the Made In America B&W Companion 3700 5th wheel hitch!

Click to Enlarge

Click to Enlarge

heavy and strong! But terrible design. Forward and back pivots smooth but side to side the fifth wheel moves on a half moon under two pins... first time out I thought I was loosing the trailer. Every corner expect a slam and your truck to shift. Its embarrassing to ride around with a truck that sounds like it’s going to fall apart. Would not recommend.

Click to Enlarge

Click to Enlarge

Took almost a week before etrailer shipped it, but then it arrived within couple days. Great hitch, perfect for those with Flatbed Trucks.

Ive been using this fifth wheel set up for about 5 months now and I don't have any complaints. I pull a 2022 Heartland Cyclone 4006 toyhauler fifth wheel. Loaded down its usually weighing between 18 to 20,000 lbs depending on what we are hauling.

Click to Enlarge

Easy to order from etrailer with fast shipping. Ordered on Mon estimated delivery on Fri but came in only 2 days for a deliver Wed. Curt A25 hitch packaged very well good instruction easy assembly on tailgate filling installed and torqued in less that 30 mins.

Click to Enlarge

Excellent on all levels. Fast shipping via right company.

Click to Enlarge

I would give this hitch 5 stars but it was damaged when I got it. The handle was apparently dented when it was shipped so I had the choice of either sending sending back a 125 pound hitch or banging out a dent in the handle and getting the damn thing installed.

easy setup! All tools required are in the picture, minus a torque wrench. If you are looking at this for your fifth wheel, get it. etrailer was very fast shipping and Alexis was awesome on the phone answering all my questions. 2021 silverado 3500 hd dually 8ft bed. Plenty of room back here for activities - I mean cargo. The box was not damaged, unboxing was simple and instructions were very easy.

Click to Enlarge

Click to Enlarge

I had a very hard time finding a hitch to fit my 2021 Silverado, but after a a call to etrailer they answered all of my questions and went above and beyond to get me the best hitch for my truck and camper. Thank you