Summer Starts Here - Save up to 70%
# 1
Malone SeaWing Kayak Roof Rack w/ Tie-Downs - Saddle Style - Clamp On
Easy loading with a secure tie-down. This is the kayak carrier you should get the first time. I've used flat bars with foam pads - they deform the hull of plastic boats. I've used J-hook style carriers which work well and hold the boat securely without hull deformation, but they increased the windage and are too hard to load on the top of a 4WD pickup. The Malone SeaWings let me slide the kayak on from the rear of the cab while standing in the pickup bed. I use an old bath mat to protect the cab and I can have the boat loaded and tied down in about 5-10 minutes. I also think the load is much more secure than any of the other carriers I've used, especially if the tie-down strap is wrapped around the load bar. The design of the SeaWing puts the main load out on the curved portion of the hull rather than across the flatter area of the bottom and totally avoids deforming the hull. In 90-100 degree heat this is very important to me. Great product. I'll probably get a second pair so I can load two boats on the truck.
We are very pleased with this product. My wife's 12.5" and my 17" kayaks are easy to load, tie down and, hold them both securely for highway speeds. Once we are at the launch site, kayaks are just as easily offloaded. Great design, simple and elegant.
# 2
Thule Portage Canoe Carrier w/ Tie-Downs - Gunwale Brackets - Side Loading
As all Thule products the Thule universally mounted canoe carrier is great. It came with all required items for safe and easy canoe transportation. There are two straps with pull to fasten for the canoe down, two tie down ropes for each end with nice pull tight and release mechanisms for the cord as well, along with two straps to fasten to the canoe ends used with the pull to tighten cords. The Chevy traverse cross bar had to have the plastic end caps removed for use with Thule canoe carrier. This was because my canoe took up the entire cross bar width to allow for Thule mounts. It is not a big deal to remove the plastic end caps. They only provide a finished stream lined look. Happy and Safe Canoeing
After retiring my 1999 Chevy Silverado 4x4 pickup, I purchased a 2017 Subaru Outback as a replacement vehicle. To transport my 1981 17 foot QT17C Alumacraft canoe on the factory installed roof rack crossbars that came with the Outback, I selected the Thule Portage Canoe Carrier w/ Tie-Downs - Gunwale Brackets - Side Loading - TH819 to do the trick. With one previous transport of the canoe sitting directly on the Outback roof racks, I realized those Outback roof racks were not as durable as the racks on my truck so I sought an improvement to avoid future scuffing and scratching. I did some advance research online and couldn’t be more pleased with this purchase from etrailer.com. I now have a quality product at the right price and these gunwale brackets are a simple solution for this veteran canoe man. The padded brackets grip the canoe and stopped the scratches. The high-quality load straps are nice with the rubber pad that covers the buckle and they easily snug the canoe tight to the racks. I’m also impressed with the bow/stern tie downs that have a very nice ratchet and clip on one end and I secured the supplied hook with a bowline knot to the other end of the ¼ inch rope. The Outback did not have convenient anchor points on the front or back of the vehicle for tie down locations but I found a good solution there as well by ordering the Thule Bow/Stern Tie-Downs - Qty 2 - TH530. This works well with the tie downs I mentioned previously. One limitation to be aware of with the Subaru Outback roof racks and this product is the width of your canoe. My 17-footer measures 34 inches at its widest point at the portage yoke. I had to place the four brackets up tight against the inside roof mounting to achieve the spread and accommodate the canoe placement. The canoe ended up fitting like a glove on the padded brackets. When placing the strap to hold the canoe down to the crossbars, I ran the strap through the vehicles tie down points and then under the crossbars for added security. Total product installation time including securing the canoe can easily be achieved in approximately 20 minutes. I look forward to many more years of safe and happy canoeing. I give etrailer.com an excellent rating for the entire ordering and shipping process on top of the high level of satisfaction with the products I purchased through them. Their customer service and price ensured me that I’ll do more business with them in the future.
# 3
Yakima SweetRoll Kayak Roof Rack w/ Tie-Downs - Saddle Style - Clamp On
Excellent product, easy install, secure on the crossbars, a bit lower ride height and a simple rolling mechanism. A significant improvement over my older Yakima Handroll racks.
The Sweet Roll will not support my Old Town Topwater 10.6. The brackets spread out on the crossbar under the weight. This year I will try a Yakima Big Catch. The Sweet Roll works fine with our Old Town Loons.
# 4
Thule Hullavator Pro Kayak Roof Rack and Lift Assist w/ Tie-Downs - Saddle Style - Universal Mount
Bought a pair of these to go on 59" rhino rack bars on our Outback Wilderness and am really pleased. I left the bars full width - they are not a head banger on the car - and mounted the Hullavators as far outboard as possible which means the kayaks clear the side of the car and wing mirrors without folding them in. I did have to modify one Hullavator to make the Hobie Lynx fit (36" wide Lynx = 36" max Hullavator width)
The Hullivator was for my wife to give her the option of loading and unloading by herself. It couldn’t be better. She now goes kayaking anytime she wants with little effort and no need for me to help her. Excellent product that’s worth every cent. Was super easy to install too.
# 5
Malone J-Pro2 Kayak Roof Rack w/ Tie-Downs - J-Style - Fixed Arms - Clamp On
Super easy to install, quality built, rock solid paring with crossbars. Zero doubt about safety. Could not ask for a better product. Worth every penny. And they fit perfectly with the Malone crossbars for my 2019 Equinox. Customer Service via chat helped me find the one and only pair that would fit those crossbars. So glad I found etrailer.
I'm writing this review after one year of ownership. I bought two sets of these J-hooks alongside a Malone Airflow 2 roof rack for our 2009 Subaru Forester. I use them to haul a 10ft and 12ft kayak simultaneously. They've done an excellent job and have held up on both short 20-minute drives to local lakes as well as on 10-hour road trips. I'm very satisfied with the combination of the rack and these carries. My only complaint is that you also need to buy the "Aero Style Crossbar T-Slot Fit Kit for Malone Kayak Carriers" pack separately for each set of J-hooks. This part allows you to more securely fasten the hooks to your roof rack. I wouldn't have been comfortable taking kayaks on a road trip using the J-Pro2s without this extra ability to secure them down. I wish the two items came together instead of having to buy them separately. That said, they do the job exceptionally well, so it's not a dealbreaker in my eyes.
# 6
Thule Hull-A-Port Kayak Roof Rack w/ Tie-Downs - J-Style - Fixed - Clamp On
Arrived quickly and was very easy to assemble and attach to the roof of my Jeep. Now that I have the initial setup complete with the proper placement of the entire system, attaching and removing the kayaks will be a breeze. Will definitely make hauling our kayaks much easier and safer.
I think the Thule Hulaport kayak racks are the best, most secure way to transport your kayaks. I had these on my Xterra and hauled two kayaks up to Cape Bretton park in Nova Scotia, Canada from Connecticut, USA no problem. We were even able to store gear in the kayaks for the trip. I’m so excited to have them for my Crosstrek. Highly recommend these!
# 7
Thule Top Deck Kayak Roof Rack w/ Tie-Downs - Saddle Style - Clamp On
This kayak carrier works great with my factory Rav4 roof rack and 10' Tamarack Angler kayak. I did break one tightener knob but probably over-tightened it. And it was replaced for free. I can load and unload the kayak easily and it doesn't budge going down the freeway. I can even drive in and out of the garage with the kayak on the rack for easy storage hanging from the rafters.
Installed this Thule Top Deck Rooftop Kayak Carrier System with tie onto our Thule Roof rack system. Easy to install and this will carry our handmade 17' Wooden Sea Kayak. Very well made.
# 8
Malone SeaWing Kayak Roof Rack w/ Load Assist and Tie-Downs - Saddle Style - Clamp On
I am happy with my purchase of the Malone SeaWing with the load assist feature. I use it a lot and it is holding up well. I have square crossbars, and the wing base can be flipped over during assembly to fit square bars perfectly. The load assist really does make it easy to get my 14 and 16 foot kayaks on the car by myself. Another reviewer stated that the load assist feature put black streaks on his thermoformed kayak, and I had the same experience. I fixed that by wrapping heavy duty, double sided Velcro around the areas of contact, and that has worked fine. They are still in place one year later. Four stars because Malone should have covered the load assist sliders in a non-marking material.
The lift assist would not work with a skin on frame kayak. Repeated use would damage the skin. You can see in the pic that the load assist pushes in on the skin, and would not slide all the way into the storage position without lots of pressure on the kayak. Etrailer would not take retuttome inern since I installed the rack, but there was no way to know without trying. So bottom line - don't try to use this on a skin on frame kayak. And don't count on etrailer for returns when they sell a product that doesn't work as advertised.
# 9
Yakima Kayak Roof Rack w/ Tie-Downs - Saddle Style w/ Rollers - Clamp On
Looks good. Fits good. My truck is tall. I am small. The rear roller rack makes loading the kayaks easy enough. I have not traveled with them yet.
This combo makes loading and unloading a quick and easy one man job.
# 10
Malone DownLoader Kayak Roof Rack w/ Lift Assist and Tie-Downs - J-Style - Clamp On
I can't lift my kayak onto my roof rack like I could when I was younger. This looked like a perfect answer to keep me actively using my kayak. It is simple to use, but it does take some strength as you have to lift your kayak onto the loader and must lift the kayak up onto the roof rack as it only loads to just before the top, so keep that in mind. The legs need to be about 6" - 8" longer as mine don't touch the ground at the connectors. I can only reach the ground with them lowered to where they are almost out of the holder. They also touch the Jeep, so I am going to have to carry something to fit between the loader and the Jeep to prevent scratching the door paint. I think if the legs were longer and they fit with both the holder/connectors then I think they might not touch the Jeep. I would have given 5 stars if the legs were long enough. It works with both my moulded J rack and my fold down J rack. It works with both style of kayaks, rounded and straight hulls.
About a year ago, I purchased one set of the Malone Downloader w/Lift Assist (MPG114MD-351XL) and second set of Downloader J-Style Folding Racks (MPG114MD) for use on a 2014 Subaru Outback with standard Subaru roof racks. I had no issue with installation and use of any of the parts using the enclosed instructions and online videos. Everything seems to fit properly and securely; no broken, unusable, or missing parts. Over the past year we've use the racks extensively for our 10.5 ft recreational kayaks on both short local trips and longer highway trips. We augmented the roof racks with T-handle hood and tailgate tie-downs and some locally purchased camlock tie-down cords. Everything working great with 10's of racking/unracking episodes. We've only used the Lift Assist maybe 1 of 10 trips when there's only a single person lifting, so can't provide as much feedback. However, the Lift Assist does work exactly as advertised and we're happy with the results. In addition, the friendly and well-informed folks at etrailer.com were a huge help with answering tech questions. Well done!
# 11
Inno Locker Watersport Roof Rack w/ Crossbar Pads - Locking - Clamp On
Heavy duty. Easy enough to install. Instructions aren't great, but you can figure it out. The crane is a good idea in theory, but could use some design refinement as it only lifts just enough to tuck a paddleboard underneath. The rachet system is great and the rubber coverings for the wires are super helpful for preventing scratches.
I installed the unit and so far i love it. It holds the kayak very securely, and they are very sturdy and robust
# 12
Rhino-Rack Kayak Roof Rack w/ Tie-Downs - J-Style - Folding - Clamp On
First experience with purchasing from etrailer. Absolutely felt that my order was personalized which is a nice touch. The Rhino Rack S512 folding JStyle Kayak holders arrived boxed impeccably with no damage whatsoever and the price was great! Fantastic first time experience. Looking forward to using them. Thank you.
Received crossbars when promised. Installation was straightforward. Was missing a couple parts. Informed company and they responded quickly with replacement parts. Very pleased.
# 13
Rhino-Rack Nautic SUP or Kayak Roof Rack w/ Tie-Downs - Saddle Style - Clamp On
After attempting to mount the individual rack pieces using the “burglar proof” button head screws with the pin in the recess and the short hex wrench with the hollowed out end I discovered that no real burglar would want the rack but would rather have the kayak so the first thing I did after spending 10 minutes trying to insert the hex into the button head screws with the pin inside the recess and attempting to turn the bolts and continually being obstructed by the support pieces and the paint interference on the bolt heads with trying to get the wrench into the recess I knew it was going to be a long frustrating process so I threw them away and purchased new button head stainless steel bolts and a 4mm extended handle hex wrench to turn them. Smartest thing I ever did. You not only have to mount the rack initially but then you have to put the kayak on the roof and remount all pieces again to fit your boat. All kayaks are different to one degree or another. Having to move the individual support and retighten them with the boat on the rack is even more difficult to do than the initial mounting with these “burglar proof” bolts and hex wrench and you will be happy you threw them away before you started the entire process. Try it for yourself at first and then go get the alternate ones. Worth the little investment and stainless steel will not rust away when you want to remove the rack system in the future. Once the rack is on your vehicle and kayak in rack the tie downs supplied are very good quality. Make sure you use the recommended tie down locations and directions, two kayak body ties and ties at front and rear. Due to numerous kayak hull designs it would be nice to have each support pod have a horizontal swivel built into it so it readily conforms to the hull shape. The overall quality of the system should be the last rack you will have to purchase. I only had issues with the supplied bolts and hex wrench. I gave this rack system a three star because of the bolts and hex tool and the individual pods not swiveling and I haven't at this point transported the kayak anywhere so I am waiting to see how it handles long trips with wind loads and constant loading and unloading performances.
Works great. I’m 5’6” and the pivoting cradles make for easy loading and off loading. I do need a stepping stool to install the carrier on the roof rack.
# 14
Yakima JayHook Kayak Roof Rack w/ Tie-Downs - J-Style - Fixed - Clamp On
Have only taken it out once so far but it was easy to put on and use. Could be easy for someone to steal, I put bike locks on mine to prevent that.
I have used these before, so this is a slightly different version, but equally functional. Directions are easily understood and it works on a variety of roof racks.
# 15
Yakima JayLow Kayak Roof Rack w/ Tie-Downs - J-Style - Folding - Clamp On
The product seems great but I have not figured out how to get it safely attached to my bars. I have an Agricover Adarac on the bed of my truck and the crossbars are 1-1/2 x 1-1/2 inches square. I thought this would work well since it's for up to 3-1/2 x 1-11/16" crossbars, but it isn't secure on these. I'm going to try and figure out an alternate method for attachment though. Thule Hull-a-port Pro's are the perfect (mounting) solution but don't seem to be made any longer.
Great product and great customer service! Very easy to install, but I highly recommend to watch the installation video first. We used typical black office clips to clip the excess straps down since they came untangled when driving. Also, I recommend to purchase locks for the racks since we are concerned someone may steal them because they are so easy to take on and off.
# 16
etrailer Kayak Carrier w/ Tie-Downs - J-Style - Folding - Clamp On
Brought home a new kayak yesterday using this J cradle for the first time. Easy to set up and load. Two complaints: not impressed with the strap buckles - had to tie knots to secure. And the 3-inch bolts weren’t long enough to easily attach the cradle to my Rhino Rack crossbars, so I had to replace them. Also got my finger pinched pretty good adjusting the cradle knobs - my fault for not being more careful, but just saying …
Great product for the price - The cradles were very easy to mount (and lay flat once folded). The videos were helpful in showing how to set the straps in the most efficient way. I test-drove my car today with my fishing kayak on top on a 80-mile round trip (a mix of freeway, country road and dirt tracks). The kayak was perfectly still, no particular wind noise and I was able to muscle to kayak up the roof and take it down on my own (it's a 52 lbs boat). I really recommend that product and I'm glad I went for J-Style cradles!
# 17
Thule Stacker Kayak Roof Rack w/ Tie-Downs - Post Style - Folding - Clamp On
We needed a better way to haul around 3 kayaks and after looking at a number of options, we settled on the Thule Stacker setup. Installation is simple and the stackers provide a sturdy option for hauling multiple kayaks. One of the best features is that they fold down when you don't need to use them. My shopping experience with etrailer was smooth and shipping was prompt.
My wife uses these to carry two small kayaks in the roof of her Subaru. They work great and we very happy with the purchase. She also likes finding her car easier in the parking lots, even with the carriers folded down.
# 18
Curt Kayak Roof Rack - J-Style - Folding - Clamp On
Well made, decent price, free and fast delivery. My only complaint is about how awkward it is to get the straps up and over the kayak. But that is true of most carriers of this design.
Good quality materials and easy to install - and uninstall. Two changes would give this product 5 stars: Some type of strap holder at the top of the back rack would make it easier to strap down the kayaks and some type of security lock so someone doesn't borrow your new racks while you are out kayaking. One unique thing to remember for the 2017 Toyota RAV4: the back OEM cross bar is about 3" shorter than the front cross bar - this takes some adjustments for the placement of the racks to fit 2 kayaks and still open the rear hatch.
# 19
Rhino-Rack Nautic Roof Kayak Roof Rack w/ Tie-Downs - Saddle Style - Clamp On
The Rhino Rack cradles, straps and hardware are all good quality and I have no complaints. The only issue I have, and the reason for only a 4 star rating, is the supplied M6 x 40mm Security Head screws are too long for the factory cross bars on my roof rack. When I first installed the cradles if I had tightened the screws all the way, the ends would have dug into the roof and paint, even before I added the weight of the kayak. In checking, I can purchase some M6 x 25mm Security Head screws from Amazon, but frankly part of me feels that for what I’ve already paid for this kit I shouldn’t have to spend another $15 for the correct length screws, plus the package has 20 screws and I only need 8. However, it appears that is exactly what I will have to do. At least they will be stainless steel, rather than the cheaper material the current screws are. Plus I will have extras for when/if the head strips out. I would suggest Rhino Rack consider included in their kit two sets of screws to meet this need. Keep the length they have, Judy add a set of 25mm. I’m still happy with the purchase but not 100%. I do like how the kayak slides easily on the rear felt lined cradles. Plus Rhino Rack includes every tie down strap that you will need, e.g. one each for the bow and stern in addition to two straps intended to secure the kayak directly to the roof rack cross bars. I would highly suggest you get in the habit of using all four straps, you really don’t need to have a gust of wind lifting the nose and tearing the roof rack off your vehicle. Can happen! My brother-in-law lost his roof rack exactly in this manner. So happy yakking and safe travels down the road. By the way I have paired these cradles with the Rhino Rack RTL002 T-Load Hitch Mounted Load Assist and Support Bar for 2” Hitches also purchased from eTrailer. I’ve attached some photos showing my first and second attempts to solve my dilemma. I need to order the replacement screws. First attempt after dark was a large flat washer, then the next day I added some nuts under the large washer. NOTE: Photos may post in reverse order.
This product was very easy to install. I had it installed in about 15 minutes and my kayak on the roof a few minutes later. The only issue I had was one of the tie-down straps was broken (stitching was not complete or something). Other than that, this product was great! The customer service (Carol and Neil) were great also, helping with the strap problem. Thank you again!
# 20
Rhino-Rack SUP and Surfboard Pads w/ Tie-Downs for Crossbars - Universal - 33-1/2" Long - Qty 2
These pads worked well on our Yakima RailBar Crossbars- Item #Y00448-0449 that we also bought from etrailer around 2020/2021. Not sure if etrailer carries the exact Yakima Crossbars anymore, but think they have a similar model. Both the pads and crossbars work well to haul our kayak on our 2019 Subaru Forester. etrailer's customer service rocks! We had a lot of questions purchasing both items and they were great to talk to!
The product came quickly and was so easy to install on my existing roof rails! It is absolutely perfect to fit many needs above and beyond my kayaks and paddle boards. They look so good on my new 2019 Jag F-Pace I might leave them on all the time.
What our customers are saying:
"very easy to shop"