Most Popular Class III for 1989 Jeep Grand Cherokee

Wow, sturdy is what I can say! Nice drop at 2". I have a Grand Cherokee with the air suspension, so I can adjust to what I need.

Thank you, thank you - product is made in AMERICA !!!!! No Chinese junk.

Nice combination to go with my front hitch for the F150.

Excellent quality. Very heavy duty. The mounting flange is 3/4" thick. Just FYI: The 4 inch drop is measured from the top of the square mounting tube to the top of the ball mounting flange. When installed inverted, the 2 3/4 inch rise is measured from the top of the square mounting tube to the top of the ball mounting flange. (Note that the "top of the square mounting tube" varies when you invert the mount for rise versus drop.)

Everything arrived on time as usual from etrailer.

Wow, sturdy is what I can say! Nice drop at 2". I have a Grand Cherokee with the air suspension, so I can adjust to what I need.

Thank you, thank you - product is made in AMERICA !!!!! No Chinese junk.

I haven't been able to use yet, however the only draw back was that I was under the impression that the pin came with it. It was my mistake because I didn't read the description fully. Can't wait to get to use.

Click to Enlarge

Click to Enlarge

Simple and it works.

I am using the hitch for a car dolly and a bike rack. The fit is a little loose for the bike rackmI'll see it really works when get on the road.

The ball mount did not fit onto the shank. This was a very disappointing experience.

The fit of the U channel for the ball mount was too tight over the verticle drilled box tube. It needed “persuasion” to get it over the tube. This will make height changes away from the shop difficult. No rattle though.

As advertised and quick delivery, I am an Etrailer fan!

Strong and works perfectly!

After being told it would cost around $1300 to install a trailer hitch I figured I would just rent a truck if I needed to pull a trailer. When I saw your ad I was in but was concerned that it would be too complicated to install myself. I turned out to be super simple including the electrical wiring. I'm recovering from a knee joint replacement so was concerned I couldn't get where I needed to be to get the job done but it was a breeze. Everything works beautifully and is solid as a rock. Thanks for such an exceptional DIY product. Now if you have a hitch for my other car, a 1962 Willys Utility Wagon. I'd like one.

Great fit in my 2016 Jeep GC

Click to Enlarge

I cannot use this ball mount because the shaft is too short that goes into hitch receiver on my one ton Dodge truck. It does not allow enough room between truck back bumper and ball to allow any trailer tongue to be put on ball.

Click to Enlarge

Click to Enlarge

Purchased this hitch as a companion for our Reese anti sway control. The small ball for the Reese sway control fits in the bracket and the 2” drop on the hitch is exactly what we needed to have our Jayco camper level when towing.

Click to Enlarge

Click to Enlarge

It is the right size for 2016 Jeep Grand Cherokee. Gives 3-4" clearance from bumper to ball. And 19" height to top of steel bar and 22" to top of ball.

I haven't been able to use yet, however the only draw back was that I was under the impression that the pin came with it. It was my mistake because I didn't read the description fully. Can't wait to get to use.

Click to Enlarge

Click to Enlarge

Good ball mount. Meets my requirements for proper trailer alignment.

Fits perfect

I haven't been able to use yet, however the only draw back was that I was under the impression that the pin came with it. It was my mistake because I didn't read the description fully. Can't wait to get to use.

Click to Enlarge

Click to Enlarge

Perfect fit, Great quality, Incredibly fast shipping! Overall completely satisfied without a single complaint or issue. Now time to buy a boat!

Click to Enlarge

The super extra long ball mount is perfect, gives the extra distance between tow vehicle and trailer because without the extra long mount there is only 32" between vehicle and trailer wall. A friend borrowed this trailer and when he backed up the trailer hit the rear tail light and crushed the corner of his truck. With the extra long mount at least the trailer corner wall will clear if this ever happens again. Also great if you have a rear mounted spare tire

This makes an EXCELLENT knee knocker and pulls a trailer even better. Really stands out from the back of the Grand Cherokee which is exactly what I wanted.

I haven't been able to use yet, however the only draw back was that I was under the impression that the pin came with it. It was my mistake because I didn't read the description fully. Can't wait to get to use.

Click to Enlarge

Click to Enlarge

Perfect fit, Great quality, Incredibly fast shipping! Overall completely satisfied without a single complaint or issue. Now time to buy a boat!

Click to Enlarge