What Bolts Should I Use To Install A Draw Tite Class 3 Trailer Hitch
Products Featured in This Question
Question:
Can you tell me if the attached hex screws are strong enough for your Draw-Tite Max-Frame Trailer 2-inch Hitch Receiver - Custom Fit - Class III ? They are Everbilt M10-1.25 x 35mm metric cap screws, zinc plated, to be used with 3/8inch conical washers. Are these a safe and reliable choice? Thank you! Tom
asked by: Tom W
Expert Reply:
While grade 8 bolts like you have are recommended to install a class 3 trailer hitch, I do not recommend using the bolts in your picture. For a trailer hitch like the Curt #14001 you were looking at, it uses 1/2" x 13 grade 8 bolts. Hitch manufacturers including Draw-tite and Curt recommend only using manufacturer approved hardware. We can provide a complete hardware kit of all manufacturer approved hardware in part # RHK. Just enter to correct part number from your hitch before adding to your cart. That way we can ensure you are getting the correct bolts.
(click to enlarge)
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class IV
- 1000 lbs TW
- 10000 lbs GTW
- 12000 lbs WD GTW
- 2 Inch Hitch
- 1200 lbs WD TW
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Trailer Hitch
- Shop: Replacement Hardware Kit for Trailer Hitches
- Shop: Trailer Wiring
- Shop: Brake Controller
- Video: Let’s Check Out the Curt Class 5 Universal Weld-on Hitch w/ Brackets
- Shop: Curt Class 5 Universal Weld-on Hitch w/ Brackets - 2-1/2" Receiver - 44" Wide
- Shop: Replacement Hardware Kit for Curt SecureLatch Pintle Mount
- Search Results: heavy duty receiver hitch
- Shop: Curt Class 5 Universal Weld-on Hitch w/ Brackets - 2" Receiver - 44" Wide
- Search Results: trailer wiring
- Search Results: custom fit vehicle wiring
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: 7- and 4-Pole Trailer Connector Socket w/ Mounting Bracket - Vehicle End
- Search Results: replacement hardware for hitch
- Video: Feature Review Replacement Hardware Kit for Trailer Hitches
- Search Results: 13416
- Q&A: Size of Install Bolts that Come with Curt Hitch 13571
- Q&A: Does 2003 Lincoln Aviator With Tow Package Have Tow Port for Brake Controller
- Search Results: waterproof wire connector
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: Replacement Hardware Kit for Curt Trailer Hitch Receiver 13416
- Q&A: Replacement Hardware Kit For The Curt Class III Trailer Hitch # C13135
- Video: How to Install the Curt Trailer Hitch Receiver on a 2016 Buick Encore
- Video: etrailer Electric Trailer Brakes Spec Review
- Video: How to Set Up Your T-One Vehicle Wiring Harness for Factory Tow Package on a 2004 Toyota Highlander
- Q&A: Is Thread Locker Necessary on Bolts When Installing a Trailer Hitch
- Q&A: What If The Bolt Holes On The Bumper Are Rusted Away On My 2003 Chevrolet Silverado 1500?
- Article: How Much Trailer Can I Really Tow
- Shop: Towing Mirrors