Replacing the Drop Leg Spring Loaded Pull Pin on a Bulldog 180 Series Square Jack
Updated 01/31/2014 | Published 01/29/2014
Products Featured in This Question
Question:
The spring broke in one of my landing gears. Is the spring available and how hard would it be to replace?
asked by: Ray L
Expert Reply:
For a Bulldog 180 series jack you will need replacement drop leg pin # BD500177. It includes the spring, cotter pin, and washer. You should not have to remove the inner drop leg to replace the pin and spring. Start by pulling back on the pin. Then use whatever tool will fit to pull out the cotter key. Then everything should come out.
Then you will put on the spring, washer, and the cotter key goes on last to hold it all in place so put it back in the way that it came out.
The spring alone is not available as a separate part.
Product Page this Question was Asked From
Bulldog Square Jack - Drop Leg w/ Spring Return - Sidewind - 26" Lift - 10,000 lbs
- Camper Jacks
- 5th Wheel Camper
- Landing Gear
- Side-Mount Jacks
- Steel
- 9001 - 10000 lbs
- Manual Jack
- 26 Inch Lift
- Weld-On
- 1 Jack
- Bulldog
more information >
Continue Researching
- Shop: Replacement Return Spring for etrailer and Ram Square, Direct Weld Jacks - 10,000 lbs
- Shop: Replacement Drop-Leg Pin for Bulldog Heavy-Duty Square Jacks - 3/4" Diameter
- Video: Review of etrailer Replacement Return Spring etrailer Ram Square Direct Weld Jack - TJD-12000-RSP
- Shop: Replacement Inner Tube with Drop Leg, Foot, and Pull Pin for Curt Heavy Duty Direct Weld Square Jack
- Shop: Square Direct Weld Jack - Drop Leg w/ Spring Return - Sidewind - 25-3/4" Lift - 10K
- Q&A: Are the Spring Returns of Bulldog Jacks Repairable if the Spring Return Function Stops Working
- Video: Breaking Down the Center Hanger for 2" Wide Slipper Springs
- Shop: Replacement Plunger Pin Assembly for etrailer and Ram Square, Direct Weld Jacks - 10,000 lbs
- Search Results: demco coupler
- Video: In-Depth Review of the Replacement Drop-Leg Pin for Bulldog Heavy-Duty Square Jacks
- Shop: Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers - Rear Axle
- Shop: Suspension Enhancement
- Shop: Curt Channel-Mount Coupler - Squeeze Latch - 2-5/16" Ball - 15,000 lbs
- Q&A: Replacement Spring for Bulldog Sidewind Jack with 12000-lbs Capacity
- Shop: Trailer Wiring
- Search Results: ez lube plug
- Search Results: dexter trailer bearings races seals caps
- Q&A: Determining The Correct Replacement Drop Leg Return Spring For 10,000lb Side Wind Trailer Jack
- Q&A: How to Tell Left and Right Side of a New Dexter Axle without Taking Off the Hubs or Brakes
- Q&A: Replacement Wheel Stud For Dexter Hub & Drum 8-219-13UC3
- Search Results: bulldog jack parts
- Q&A: Choosing Spring Return Or Non-Spring Return and Handle Recommendation For Bulldog Square Jack
- Video: Bulldog Powered-Drive Kit Review
- Search Results: 9/16 lug nut
- Search Results: lug nut
- Search Results: 9/16 wheel studs
- Q&A: How to Rewire an Old Cattle Trailer
- Video: Feature Review Curt Hitch Receiver Reducer Sleeve
- Video: In-Depth Review of the Curt Hitch Receiver Reducer Sleeve
- Video: Comprehensive Review: Hopkins Smart Hitch Backup Camera and Hitch Aligner System