Roof Rack that Can Fit Top Channels of Leer Camper

Question

Question:

Hi there! I have a 2007 Ford F-150 with a Leer topper. It has factory rails on it. I’m wondering what system/ fit kit I need to install a basic roof rack with cross bars. Thank you!

asked by: Sam

1

Helpful Expert Reply:

For a roof rack that would fit the channels you have on top of your Leer camper shell the Thule TracRac CapRac part # TH29200XT would be a really great option. This is a higher weight capacity rack that fits directly to the channels with top channels and load stops. The bars are 69 inches long overall.

expert reply by: Jameson C

1

Answer 1

The Rhino-Rack Roof Rack for Factory Tracks - 2 Vortex Aero Crossbars #Y02-480B-NT will work just fine with your LEER camper shell with 45" tracks. Since you already have tracks on your camper shell you'd just need to attach the feet and…

view full answer...

Answer 2

If you were to measure the width of the track that would then give you the best chance of identifying it. However, this really is not needed because the slots are pretty much universal so you can mix and max brands. The most cost effective system we…

view full answer...

Answer 3

I do have an option for you but the Thule Tracker System you have now has been discontinued and Thule no longer makes parts for this. The tracks can remain on the cap but you will need to replace the fit kit (block with bar) and then add a foot pack…

view full answer...

Answer 4

I spoke to my Yakima contact and he informed me that you will need the Landing Pad 1 #Y00221 for the tracks on your Leer camper. To complete your roof rack setup you will need: quantity 2 of the Landing Pad 1 #Y00221 quantity 4 of the Control Towers…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The Rhino-Rack Heavy-Duty Roof Rack Roof Rack have specific C-channels that are designed to fit specific Rhino-Rack Heavy-Duty accessories, like the Rhino-Rack Hi-Lift Jack and Shovel-Holder Brackets #RRRCB-RSHB-RJHB as an example. That's the…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew, your best option would be to go with the Rhino Rack roof rack part #RR23VE that is a confirmed fit for your 2012 GMC Sierra and then also get the fit kit part #DK454 so you can swap it to the 2019 Honda HR-V. The bars will be a little bit…

view full answer...

Answer 9

The 59" rails that come with the Rhino-Rack Roof Rack System w/ 2 Vortex Aero Crossbars #Y02-490B that you referenced can be cut to length according to your needs with your 2016 Toyota Tacoma. However, I do recommend going with the part…

view full answer...

Answer 10

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 11

The 71" Rhino-Rack Vortex Crossbars for Retrax XR Tonneau Covers item #RRVA180B-RRRLT600 are the correct set for your 2022 Ram 3500. These are made for full size trucks and fit in the rails of the Retrax PRO XR. These crossbars are exactly…

view full answer...

Answer 12

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Roof Rack that Can Fit Top Channels of Leer Camper

Product Page this Question was Asked From

Continue Researching