Attaching Motorcycle Wheel Chocks to Toy Hauler Floor

Question

Question:

cannot access underside of 3/4 inch plywood trailer floor to through bolt. Will these work? bike is Harlet ultraclassic

asked by: Gerry

0

Expert Reply:

Since tie down straps like # EM34410 are bearing the vast majority of the weight of the bike, attaching the wheel chock using the # TWPH2770 hardware kit is perfectly acceptable. The chock is merely helping hold the front wheel in place, the tie downs will be doing most of the work.

expert reply by: Mike L

0

Answer 1

The Tow-Rax Wheel Chock #TWSPWM is supposed to only require 3-fasteners to secure it which is why the multi-surface hardware kit, #TWPH2770, comes with 3 fasteners as well. Either way, yes, 3 fasteners can be used. I think you might have TWSPWS which…

view full answer...

Answer 2

Ideally, brake assemblies on both sides should be replaced at the same time to ensure balanced braking performance. However, it's very common for people to choose to only replace brakes on one side of the trailer and the other side at a later…

view full answer...

Answer 3

Red lithium grease such as #L11390 is one we use often here for installations and it is compatible with other Lithium formulas. I have included a link to our help article that covers grease compatibility. There are greases that are not compatible…

view full answer...

Answer 4

Acccording to MaxxAir, you'll want to remove power from the MaxxAir #MA00-04000K fan for a minute or two, then reconnect to reboot the circuit board. In the vast majority of instances, this will fix the problem. You should also check that the fan…

view full answer...

Answer 5

My contact at MaxxAir advised that there are three potential causes for the beep and no fan motion you're experiencing with your MaxxFan Trailer Roof Vent #MA00-04000K. One potential cause is that the unit was wired with incorrect polarity. Make…

view full answer...

Answer 6

Are you having issues with a MaxxAir MaxxFan roof vent like #MA00-04000K? It could be an internal issue with the fan and it needs to be replaced. Before replacing you can check a couple of things. Is it a new install? If so make sure you have the…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Well James, I can say with 100% certainty that what you are seeing and experiencing is NOT normal. However, this is not the first time we have heard of this occurring. To answer your first question, it was corrosion that caused it. To be more…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Attaching Motorcycle Wheel Chocks to Toy Hauler Floor

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching