Replacement Velcro Strips For Truxedo Pro X15 Tonneau Cover

Question

Question:

I need replacement Velcro for the side rails on Truxedo pro x15. Can I order replacements?

asked by: Bruce

0

Expert Reply:

If you have the 8' bed then you can go with Replacement Truxedo Shur-Bond Velcro Brand Fastener for 8' Beds - 1" Width # TX1117877. If you have the 6-1/2' bed then you will want to go with Replacement TruXedo Shur-Bond Hook-And-Loop Fastener Strips # TX1117876. These kits include the velcro that attaches to the bed rails, not the tonneau cover side. I attached a short demonstration video for you to check out.

expert reply by: Andrew N

0

Answer 1

For replacement Velcro for the Truxedo X15 tonneau you have installed on your 2013 Ram 2500 short bed you'd want the part #TX1117876.

view full answer...

Answer 2

There is one rivet on each side rail that holds the existing Velcro strips in place. In order to replace these Velcro strips you need to drill out each rivet, pull the strips out from the channels, slide the new strips (Replacement TruXedo Shur-Bond…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hello Rad, thanks for reaching out. Yes, the Replacement Side Rails for Retrax XR Series Hard Tonneau Covers #RTT-82381 are indeed for the 5.5' bed. I do not have a way to look up your serial number to confirm fitment though. If you contact…

view full answer...

Answer 9

Hey April, B and W doesn't have a rail or bracket kit that fits your 2018 Ford F-150 so your best option would be the Curt part #C38ZV that does fit your truck and also is compatible with the same fifth wheel rails as what a B and W kit would…

view full answer...

Answer 10

Hello Lou, thanks for reaching out. The hitch pin you are looking for is the etrailer D-Shape Anti-Rattle Locking Hitch Pin for Benton Hitch Accessories #e43JR. This will work with the Benton #B54VR bike rack you mentioned, as well as the #B54FR,…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Replacement Velcro Strips For Truxedo Pro X15 Tonneau Cover

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching