Replacement Hook Side Velcro Strip Recommendation for Truxedo Tonneau

Question

Question:

I am ordering part TX1117877 and I understand this is for the bed side. Do you carry the strips that go on the liner side? Or is replacing the bed side all thats needed to keep it from coming undone?

asked by: Dana I

1

Helpful Expert Reply:

Normally when Velcro gets weaker and needs replacing only the hook side is what wears out and would need to be replaced. The # TX1117877 would be all that you'd need and would work well. This is 96 inches long and 1 inch wide which is what 8 foot bed trucks require.

expert reply by: Jameson C

1

Answer 1

The part number on that sticker in your photo refers to the tensioning device, but luckily that narrowed things down enough to determine that the #TX1115174 Velcro strip is the correct replacement for you. It's longer than you actually need, but…

view full answer...

Answer 2

When replacing the Velcro on your TruXedo cover, you will just measure the actual hook Velcro portion. The Replacement Truxedo Shur-Bond Velcro Brand Fastener for 8' Beds - 1" Width #TX1117877 is what you want over the 1-1/4 inch wide…

view full answer...

Answer 3

In order to replace the hook and loop fasteners on a TruXedo Tonneau Cover you will need to know which exact model you have. If you have the TruXedo TruXport then you need part #TX1117877 but if you have the TruXedo Lo Pro then you need part…

view full answer...

Answer 4

If you have the 8' bed then you can go with Replacement Truxedo Shur-Bond Velcro Brand Fastener for 8' Beds - 1" Width #TX1117877. If you have the 6-1/2' bed then you will want to go with Replacement TruXedo Shur-Bond Hook-And-Loop…

view full answer...

Answer 5

We do have an option for you, however, we do not have a 1-5/16 wide by 8' long velcro replacement for your TruXedo tonneau cover What we do have is the Replacement Velcro Shur-Bond Fastener for TruXedo Deuce Tonneau Covers #TX1117785. This…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Replacement Hook Side Velcro Strip Recommendation for Truxedo Tonneau

Product Page this Question was Asked From

Continue Researching