Troubleshooting Atwood RV Carbon Monoxide Detector Beeping Every 40 Seconds

Question

Question:

Mine beeps every forty seconds and the gas has been off for a month

asked by: Jon C

0

Expert Reply:

We've seen this issue before on your Atwood RV Carbon Monoxide and Propane Gas Detector # AT36681 and the beeping every 40 seconds indicates "a fault has been detected that compromises some detector function."

What you need to do is use push the Alarm Reset button to attempt to clear the fault. If this does not work, the owner's manual states that "the detector is not functioning properly and must be replaced."

expert reply by: Jameson C

0

click to enlarge

Answer 1

The instructions state the rest/test button of the Atwood RV Carbon Monoxide and Propane Gas Detector - 12 Volt - White #AT36681 is the button on the top right, and you need to press that in and hold it down. If the rest does not work and the red…

view full answer...

Answer 2

On your Atwood RV Carbon Monoxide and Propane Gas Detector #AT36681 there is a circle Reset/Test button on the top right hand corner of the unit. Simply pressing this button should reset the detector and silence any alarms assuming there isn't an…

view full answer...

Answer 3

If the Atwood RV Carbon Monoxide and Propane Gas Detector part #AT36681 continues to beep even after a rest then this can be narrowed down to either a leak or faulty detector. If you shut off the gas supply to the trailer entirely and the alarm still…

view full answer...

Answer 4

We've seen this issue before on your Atwood RV Carbon Monoxide and Propane Gas Detector #AT36681 and the beeping every 40 seconds indicates "a fault has been detected that compromises some detector function." What you need to do is use…

view full answer...

Answer 5

It sounds like your Atwood RV Carbon Monoxide and Propane Gas Detector part #AT36681 is hooked up properly and is getting power. The code you hear is like you said a fault code in this case because of the audible tone. I recommend replacing it. The…

view full answer...

Answer 6

We do have a couple of options to replace your Atwood 36636, and you can use either, with the only difference being the color: - RV Propane Gas and Carbon Monoxide Detector - Black #RS54FR or White #RS34FR Either will work perfectly as replacements…

view full answer...

Answer 7

The red blinking light on the Atwood RV Carbon Monoxide and Propane Gas Detector part #AT36681 under the propane heading means that the propane sensor is disabled or faulty. I recommend doing a hard reset of the unit but if that does not work then…

view full answer...

Answer 8

You could use the 2-wire Propane Gas and Carbon Monoxide Detector part #RS34FR in place of the Atwood 36681 that you referenced. This would fit in the cut out you have now and has a flange that is large enough that would cover the hole.

view full answer...

Answer 9

The red blinking light on the light of the Atwood RV Carbon Monoxide and Propane Gas Detector AT36681 typically means that the propane sensor is disabled or faulty. Since you've already tried resetting the unit you'll want to make sure you…

view full answer...

Answer 10

When replacing your existing detector with the Atwood RV Carbon Monoxide and Propane Gas Detector #AT36681 you will not need to disconnect the 12V trailer batteries. It also does not matter which of the two power wires you connect first. The third…

view full answer...

Answer 11

You can use the RV Propane Gas Detector #RS64FR to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 12

The closest option we'll have to your Atwood 33535E LP/CO2 Detector is going to be the RV Propane Gas and Carbon Monoxide Detector - 12 Volt - 2 Wire - Black #RS54FR. It comes with two mounting plates to try and eat up some of your old cutout…

view full answer...

Troubleshooting Atwood RV Carbon Monoxide Detector Beeping Every 40 Seconds

Continue Researching