How to Clear Retract Time Out Return Levelers Error on LCI Level Up System

Question

Question:

I had a retract timeout error and I did what you said to clear it then after I did that I now have a right up error message and the right front and back light is illuminated red. How do I clear that?

asked by: Christi L

0

Expert Reply:

If the touch pad is showing "Retract Time out Return Levelers for service" all you need to do is hit, enter and retract at the same time. That will clear that code. I confirmed this with our contacts at Lippert.

expert reply by: Jameson C

0

Christy

4/19/2020

Getting a jack timeout error

Chris R.

4/21/2020

Is it the same error described above? If so, did you try following the procedure Jameson described? If it didn't clear/resolve the error, make sure your battery source is still fully charged and in good condition. A weak battery has also been known to trigger this error message.

Alex C.

3/13/2021

@ChrisR i have full battery with that code "retract timeout " but holding power and retrac does nothing

Jon G.

3/13/2021

@AlexC Are you able to manually retract your jack(s)? If the manual operation works but not when you use the power then there may be a plug disconnected or possibly some damaged wiring. I'd start there and then I can help you troubleshoot further if that doesn't fix it.

See All (7) Replies to Christy ∨

Retina

3/2/2024

Thank you for this information

Reba

4/13/2024

so glad you had this information online. saved us a service call. Thank you again

Jameson C.

4/15/2024

@Reba Glad we could help!

Artie P.

4/13/2024

I had removed my batteries during the winter for the 2nd year in a row. Reinstalled a month ago and all seemed fine. today when I turned on the ignition, I heard a beeping that eventually stopped after 10 seconds or so. I found out that the leveling system was producing that code and the levelers were retracted. Tomorrow I'll go back to the storage yard and try the reset trick you mentioned. This would be much better than driving 45 miles to the dealer and leaving it until they have time to look at it. Thank you for the advise

Jameson C.

4/15/2024

@ArtieP Hope it works!

Artie P.

4/15/2024

Press two buttons simultaneously and the error disappeared and the jacks go up and down. Saved me a trip to the dealer Thank you

Jameson C.

4/16/2024

@ArtieP Glad we could help!

See All (5) Replies to Artie P. ∨

Tomg

4/29/2024

Thank you for having critical info like this readily available. Just returned from a short first of season trip (3 hours), all OK. Repositioned rv and this error showed out of nowhere. Working again as advertised Thank you

Jameson C.

4/29/2024

@Tomg Glad we could help!

Jerry A.

8/3/2024

Rock solid help and advice. Thank you! Saved me a repair charge.

Jameson C.

8/4/2024

@JerryA Awesome!

Mark H.

8/6/2024

@JamesonC Do you know if there is a more "permanent" fix to this "Retract time out. return… error? I get it the error repeatably, about every time I go to use it. Error clears with the holding the enter/retract, but on next use, the error message is back. Never ending cycle....

Jameson C.

8/6/2024

@MarkH We've had Lippert tell us that it's typically a weak battery or bad wiring that causes this problem. So I'd check to make sure your battery is solid and then check the wiring connections.

Show All (13) Replies

Hide Replies

Answer 1

Hey Jeff, sorry to hear about the Advent letting you down. So to install a Furrion Chill Cube you will need a kit that includes a new lower air box and thermostat as no part of what you have now would be compatible with a Furrion or anything else. So…

view full answer...

Answer 2

That's a really good question, Lanny. If you're looking at getting one of the Ignik FireCan fire pits, part #GN67FR, part #GN99FR, or part #GN24FR, you can get a different hose to connect to your RVs quick disconnect on the side of the…

view full answer...

Answer 3

If the touch pad is showing "Retract Time out Return Levelers for service" all you need to do is hit, enter and retract at the same time. That will clear that code. I confirmed this with our contacts at Lippert. Let me know if that fixes…

view full answer...

Answer 4

Although we don't offer any ceiling mount LED lamps with a pull chain, we do offer one with a push button switch on the base of the lamp that might meet your needs, part #GUS54FR. This lamp is 10 inches in diameter would use a 9-1/4 inch glass…

view full answer...

Answer 5

Hey Richard! The Furrion Chill Cube RV Air Conditioner w Air Distribution Box #FR99TD comes with everything you need to install a complete AC system on your trailer. This includes the AC unit itself along with the air distribution box for a ducted…

view full answer...

Answer 6

Hey Chris, we have just what you are looking for with the Furrion Chill Cube part #FR69TD which is setup to work with your ducting and also has a lower vent assembly that would allow it to dump out of the bottom of the unit as well. This will be a…

view full answer...

Answer 7

Hey Will! You can flat tow your 2014 Jeep Wrangler Willys with a Dana 44 axle as long as you have a two-speed transfer case. Make sure to check your owner's manual to verify this information. Does it have the standard bumper on the front?…

view full answer...

Answer 8

We have heard of this issue before on the Lippert Ground Control systems #LC358590. Here is the recommended procedure for clearing the error code: Extend all jacks at least 6 inches. Then press and hold the RETRACT button until the jacks begin…

view full answer...

Answer 9

In order to "reset" your Lippert #LC358590 or #LC675817 Leveling system you'll want to follow these instructions: 1. In manual mode, run the jacks to level the trailer. This is best achieved by placing a level in the center of the…

view full answer...

Answer 10

Hey Maurice! We no longer recommend swapping out just the AC unit since there have been a lot of compatibility issues. Also, everything is switching to the new R32 refrigerant due to the new 2025 EPA regulations. The old parts for R410A units are…

view full answer...

Answer 11

For castle nut #165931, for a D washer use part #5-23 or round washer use part #SW1000. These are both for 1 inch spindles but are compatible with the 7/8 inch castle nut assemblies. You can also use the Replacement Spindle Washer - Tang Type for E-Z…

view full answer...

Answer 12

Hello Alicia, thanks for reaching out. I was able to cross reference the part number 140-1226. The correct replacement touch pad for this is the following: - Replacement Control Touch Pad for Power Gear RV Auto Leveling System #LC44UJ

view full answer...

How to Clear Retract Time Out Return Levelers Error on LCI Level Up System

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching