Where is Brake Controller Install Port for 2018 Ford Explorer

Question

Question:

Ive just purchased a 2018 Explorer with the factory tow package. The package includes a hitch, 7-pole wiring, and an engine oil cooler. I cannot find a _word_ anywhere through Ford regarding a brake controller or installation /wiring, and I dont see any wiring coiled anywhere under the dash... can you help with that, please? I do have a brake controller that Id like to use if its compatible... its a Reese Pod, and I believe the model number is 7746... theres a part number on the instructions, 7760, I guess thats the number of the instructions themselves... the date code on it is February 2006. Many thanks!

asked by: Doug

1

Helpful Expert Reply:

To install your Reese Pod brake controller in your 2018 Ford Explorer will require the install harness part # 3035-P which is a confirmed fit. If you check out the 9:55 mark of the install video I attached to this page you'll see where to find the port on your vehicle to plug the controller in. It is a bit hidden under the dash underneath the panels.

expert reply by: Jameson C

1

click to enlarge

Ellis

8/15/2024

Where is the full video for the 2018 Ford Explorer brake controller install. Thank you.

Reply

Jameson C.

8/15/2024

@Ellis I attached it to this message.

Helpful Links

tv-install-prodigy-p3-brake-controller-2013-ford-explorer-90195.aspx

Reply

Answer 1

Yes, 14 gauge wire seems too small. I would go with 10 or 12 gauge. For 10 gauge you can use #10-1-1 and for 12 gauge use #12-1-1. These wires are sold in increments of 1 foot. So if you needed 20 feet of wire you would enter 20 in the quantity box.…

view full answer...

Answer 2

The brake controller port on a 2019 Ford Explorer should be located behind the glove box on the passenger side or underneath and left of the steering column near the emergency brake pedal. That said, I say should because the location of the brake…

view full answer...

Answer 3

For 3,500 pound axle U-bolt kits like the Redline #APUBR-1 that use 1/2 inch hex nuts you will want to torque them down somewhere between 45 and 70 foot pounds. I have attached a great article on trailer suspension that includes this info along with…

view full answer...

Answer 4

Although it is not required by law, what you are wanting to do is certainly possible. Because trailer tail light systems combine the stop lamp and turn signals for each side onto a single circuit, you will need to use a vehicle-to-vehicle tail light…

view full answer...

Answer 5

Since your trailer uses a combined wiring system where the stop and turn signals run on the same circuit, in order to add a third brake light to your trailer you would need to use a 2-Wire to 3-Wire Converter, like part #118158. This will convert the…

view full answer...

Answer 6

If you connect the trailer brake light circuit to the trailer brake circuit your brakes would lock up immediately since 12 volts is max braking voltage for trailer brakes. You'd need a brake controller that can vary voltage so that you can apply…

view full answer...

Answer 7

To add a third brake light to a trailer is pretty simple, but does require an adapter to convert the signal. Because trailer tail light systems combine the stop lamp and turn signals for each side onto a single circuit, you will need to use a…

view full answer...

Answer 8

If your 2017 Ford Explorer has the factory prep towing package installed, then you might have a brake controller plug-in wiring on the vehicle to connect your brake controller. However, not all models with the tow package had the wiring installed and…

view full answer...

Answer 9

All of the A-frame couplers we sell are designed to fit 50 degree frames. As long as you, or the person doing the welding, is a qualified welder who knows what they are doing you could use the #BD44150WH301 on your trailer and then have wedges used…

view full answer...

Answer 10

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 11

Most A-Frame Trailer Couplers have a standard of 50 degrees. I produced a short video for you showing the angle of the etrailer A-Frame Coupler, part #CA5400. I have also linked an FAQ on trailer couplers.

view full answer...

Answer 12

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Where is Brake Controller Install Port for 2018 Ford Explorer

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching