fall hauling headquarters

T-One Vehicle Wiring Harness Installation - 2018 Ford Explorer

content loading



Customers compare 118272 to these similar products




Products Featured in this Video



How to Install a T-One Vehicle Wiring Harness on a 2018 Ford Explorer


Speaker 1: Today on our 2018 Ford Explorer, we're going to be taking a look at, I'm going to show you how to install, the Tekonsha T-One Vehicle Wiring Harness for Factory Tow Packages with Seven-Way Trailer Connector, part number 118272.This is what our wiring looks like when it's installed. It's going to provide you with all the necessary function you need for your trailer, both turn signals, your running lights, your brake lights, reverse light signal and also a signal for your brakes if you have trailer brakes. It's going to have a nice, durable, plastic cover, spring loaded cap. The cap's going to have a rubber seal in it. It's going to seal around here, it's going to keep any moisture or anything like that from getting on your connections.Your wire is going to come equipped with some wire loom to help protect it. The seven-pole plug will fit in a variety of different seven-pole holders or brackets.

As far as the installation, it is a very simple installation. It's going to plug directly into your factory wiring. All you need to do is route it over to where you're wanting to attach it to your hitch, and mount it in that location. Now that we've gone over some of the features, let's show you how to get it installed.This is what you're going to get in your kit. You're going to get your wiring harness.

It's going to connect into your factory tow package wiring. Your seven-pole plug, and your connector that's going to connect your wiring into your plug along with some zip ties. Along with your kit, I suggest getting some longer zip ties. You're going to need a seven-pole bracket. You're also going to need a short bracket and some dielectric grease.

This is going to help keep your connections from corroding.What we need to do is on our passenger side, you're going to see a plug right here. We need to unplug that, so we're going to push in the tab and pull out. You'll see our two connections. We're going to put a little bit of dielectric grease on our connectors, and then we're just going to match our plugs. Push them in until you hear them click.

What we're going to do with our wiring, we're going to go up behind the bumper. The reason is is there's nowhere to run it across here without getting close to the exhaust. We want to make sure we stay away from any heat source.I'm going to take an airline tube, you can use a wire hanger, anything that has a little bit of stiffness to it. We're going to feed it up behind the bumper fascia. We're going to come around and we're going to reach up like that. Now, we're going to take the end of our wire, tape it to the end of our airline tube. Make sure I cover those connections good, I don't want to damage the metal ends. We want to just slowly start to pull this up and over the top. It can be a little bit of a pain to get it up and over the top of that. It's got to go up pretty high and over the top or else it'll get stuck. Or it'll feel like it's stuck.It is a little bit of a pain. However, it's going to save you a lot of time and trouble later on, because this heat is not going to affect the wiring. Now what we'll do is we're going to run this over just like this. We're going to be connecting it about here, so go over top of our back of our hitch here like this. Then, we can remove our airline tube or hanger or whatever it is that you're using.Now, we're going to make our connections into the back of our plug. You can see the way this is facing, this is where you would release it off the back of your seven-pole plug. Brown, that one, that's bottom left corner here. Blue is going to go into this bottom right corner. White is going to go into this large hole over on the right side. Red is going to go just above the white. Going to go yellow, is going to go right into the center. Black is going to go right here onto the left center. Then, our green is going to go into this top left hole.What we're doing is you see that open side On the inside, there's a little tab. That little tab is what locks it into place, so we need to just get that turned so it will slide all the way in there. Going to lock that into place like that. Once we get our wires installed, we're going to take a little clip that comes in our kit. We'll slide it in like this. We're just going to pop it into place. That's going to hold our wire down.I'm going to take my included screws. I'm going to mount my seven-pole bracket to my short bracket first. Put our screws in. Take our two included nuts, then we'll just take a Phillips or flathead screwdriver, tighten it into place. What we have determined is that if we put our short bracket like this, our seven-pole is not going to fit here. Then, we won't be able to get our plug onto the back. What we're going to have to do is remove this, and we're going to flip it over. Hook our bracket on like this, and this is going to face down.Now, we're going to take our included inaudible 00:05:47 going to come up behind our hitch. Then, we'll get it tightened into place with a flathead screwdriver. Then, we can just cut off our excess. Next, we'll install our seven-pole plug with the included screws and nuts. We'll have one for each corner. Then, we'll tighten them down with a flathead screwdriver. You want to make sure that these . You don't tighten these real tight, because you don't want to crack the plastic housing on your seven-pole plug.Now, we'll take some dielectric grease again, add it to our connectors here. Plug that right into. Then, we'll take some of our longer zip ties and secure the rest of our wiring right up to the back of our hitch. Then, we can come back, cut off our excess.Next, we'll test out our wiring using an alternate power source. Left turn, right turn, brake lights, running lights. That'll do it for a look at and installation on the Tekonsha T-One Vehicle Wiring Harness for Factory Tow Packages with Seven-Way Trailer Connector, part number 118272, on our 2018 Ford Explorer.


Questions and Comments about this Video

add comment


Info for this part was:

Test Fit:
Joe V
Installed by:
Jeff D
Video by:
Joshua S
Video Edited:
Jacob T
Video Edited:
Kathleen M
Video Edited:
Dustin K
Test Fit:
Randy B
Video Edited:
Chris R
Test Fit:
Brent H
Test Fit:
Shane H
Video by:
Jonathan Y
Test Fit:
Robert C

At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.







^
About Us
photos and videos
1,056,204

Original Photos & Videos

Produced to make sure you know what you are getting and you get exactly what you need.

installations
35,570

Installations Completed

To make sure products work and fit the way they are supposed to.

etrailer call center
2,476,511

Phone Calls & Emails Answered

1,125,924 phone calls and 1,350,587 emails to help find the right solution.

etrailer training
400+

Average Hours of Product Training

We get to know our products firsthand so experts can better help you.

etrailer service
71

Years of Quality Customer Service

Assisting our neighbors and customers, face to face at the counter.

etrailer experts
193,357

Pages of Expert Information

Created to make sure you have all the answers to your questions, from real experts.