Where to Find VIN Number on Yakima Rack and Roll Trailers

Question

Question:

Hi, I am selling a 68 and own a 78 I want to make sure i am selling correct one. Where is the vin number located? Thanks

asked by: Charlie W

0

Expert Reply:

If you check out the picture I attached you will see where I pointed out where the sticker is that has the VIN on the Yakima Rack and Roll trailers like the part # Y08106.

If somehow the sticker is worn off or unreadable my contact at Yakima said that if you contact the dealer where you initially bought the trailer you can give them your name and info and they will be able to find the VIN that way as well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Replacement Left Side Fender for Yakima Rack and Roll Trailers - Qty 1 #Y8880164 and right side #Y8880163 are intended to be priced equally. The reason why they are not at this moment is that the right fender is on sale in our system. Why they both…

view full answer...

Answer 2

The Replacement Tongue for Yakima Rack and Roll Trailer #8880204 is 3/16" thick. The overall dimensions are 69-5/8" long x 2" wide x 2" tall.

view full answer...

Answer 3

Since we have started carrying the Yakima Rack and Roll trailer #Y08107 I have not heard any complaints regarding the wheel bearings failing and only a few instances where people wanted to replace the wheel assembly. If you need to replace your…

view full answer...

Answer 4

The max boat length for the Yakima Rack and Roll Trailer part #Y08106 is 17' per Yakima. It would probably work just fine with a slightly longer boat but we cannot recommend this. That said, there is another trailer that will work better for you…

view full answer...

Answer 5

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 6

Trailer tires typically last anywhere from 5000 to 12000 miles, so you shouldn't have anything to worry about with your Yakima Rack and Roll Trailer #Y08107 driving from North Carolina out to Colorado, and back. I think you're likely going to…

view full answer...

Answer 7

The tire on the Yakima Rack and Roll trailers is a 3.25-16, which is an uncommon size for a trailer. The company that makes the tire is called FEICHI TYRE. They make a lot of motorcycle tires. I went out and inspected our Yakima Rack and Roll trailer…

view full answer...

Answer 8

While there isn't a life expectancy, per se, of the shocks on the Yakima Rack and Roll Trailer - 66" #Y08106 and 78" #Y08107, upgrading to the HD shocks is absolutely a good idea if your gear weighs around 200 llbs and certainly…

view full answer...

Answer 9

I went out to the warehouse and pulled Yakima shock for Rack and Roll trailers #Y08110 to measure it. From the center of one eye to the center of the other is approximately 12-7/8 inches.

view full answer...

Answer 10

Unfortunately, Fulton doesn't offer a a folding coupler hinge kit for a 2 x 2 inch trailer tongue. I have heard from some of our customers that they've used a couple of pieces of 1/2 inch steel plate plate cut to the appropriate size to shim…

view full answer...

Answer 11

I reached out to my contact at Yakima and she said that the compressed length of the Replacement Standard Shocks #8880177 is 9.45 inches. These are designed to replace the standard shocks on the Yakima Rack and Roll Trailer #Y08106 and #Y08107.

view full answer...

Answer 12

According to Yakima, the Heavy Duty Shocks for Yakima Rack and Roll Trailer #Y08110 should only be used if you add the 78" crossmember kit #Y08111. They didn't have an exact reason for this, but it sounds like the concern is people will…

view full answer...

Where to Find VIN Number on Yakima Rack and Roll Trailers

Continue Researching