Is 16 Gauge Wire Adequate for Trailer Wiring for Lighting

Question

Question:

I am re-wiring the running lights 2/brake lights/lic plate lights on a 13 foot vintage camper. It had a 4 prong on it. Will a 16 gauge 4 prong be an adequate replacement for this system. No trailer brakes.

asked by: Dave S

0

Expert Reply:

Most trailer wiring that runs to trailer lights is 16 gauge. I would rather people use 14 or 12 unless the lights are LED which draw considerably less. But for most people 16 gauge works just fine for basic trailer lighting. If you are planning on running several running lights or just more lights in general you would want thicker wire.

I attached a help article on trailer wiring for you to check out as well.

expert reply by: Jameson C

0

Answer 1

Hey Michael congrats on the new truck! The most recent video I have of the Air Force One Flat Tow Brake System item #SM99243 being installed is on a 2020 Sierra 1500. I have linked this video below. Your 2024 is the same generation so it should be a…

view full answer...

Answer 2

Yes if you were ever stuck you could use the base plate kit like part #DM9517335 as a recovery point.

view full answer...

Answer 3

I'll pick the etrailer branded tow bars over the Blue Ox alternative any day because of some key features that set them above Blue Ox: - Triggers for easier disconnection of the arms - Integrated safety cables so you it's one less thing to…

view full answer...

Answer 4

The Roadmaster Battery Disconnect #RM93MR is the Roadmaster part number 767. This manual battery disconnect is designed primarily for diesel vehicles but can also be used on gasoline vehicles.

view full answer...

Answer 5

Disconnecting the battery on your 2022 Chevrolet Silverado 1500 when flat towing is required per your owners manual. This is most likely to prevent excessive drain on your battery and prevent the vehicle anti-theft systems from activating. We do…

view full answer...

Answer 6

You can still get the Roadmaster Direct-Connect Base Plate Kit #RM-523193-5 to fit, but you'll have to trim or even remove some of the air shutters in order for it to fit. Since that's quite a bit of modification Roadmaster just lists the fit…

view full answer...

Answer 7

Yes, the engine on your Chevrolet Equinox will need to be run at times when flat towing. The easiest way to determine what needs to be done to flat tow your Equinox is to consult your owners manual. I went ahead and took a look at the owners manual…

view full answer...

Answer 8

Congrats on the new vehicle! To flat tow your 2024 Chevy Equinox you will need the following parts: Tow Bar and Safety Chains - Roadmaster Falcon 2 Tow Bar item #RM-520 and item #RM-643 Base Plate Kit - Roadmaster Direct-Connect Base Plate Kit -…

view full answer...

Answer 9

The Roadmaster Even Brake Portable Supplemental Braking System #RM-9400 and Brake Buddy Select 3 Portable Supplemental Braking System #HM39524 are really good choices for easy-to-use portable braking systems, and have only one difference that I would…

view full answer...

Answer 10

Typically 4-way wiring consists of 18 and 16 gauge wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264. The part #HM38138 uses 18 gauge for all wires but the white that uses 16 gauge.

view full answer...

Answer 11

Grounding through the ball doesn't work well, as you've found. If the current harness doesn't have a ground circuit, the wiring must be fairly old as it's pretty typical for a trailer connector to have a ground circuit. The fact that…

view full answer...

Answer 12

Powder coating is widely considered to be superior to acrylic paint in terms of resistance to chipping, scratching, and color retention. For a wheel application powder coat will definitely look better as well as hold up better than paint. Based on…

view full answer...

Is 16 Gauge Wire Adequate for Trailer Wiring for Lighting

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching