How To Pair an Air Lift WirelessAIR Remote to Compressor
Question:
How to program a new wireless controller to the compressor???
asked by: Oscar R
Expert Reply:
In the settings mode of the controller you can join the manifolds with the controller.
To set the manifold into join mode locate the yellow join wire. It is the yellow wire with heat shrink on the end of it. Remove the cap leaving it attached to the harness. Attach the exposed terminal to a good frame ground. Now the manifold will boot into join mode and will click the exhaust solenoid 5 times fast then one per second. The manifold will stay in join mode for 30 seconds.
On the controller hold the up and down buttons together. Cycle through the different options at this point by pressing the up button. Once you see Join on the display press the M1 button.
Use the up and down button to select which axle you want to join with. Press M1 when you have selected the correct axle you want. The display will show done when complete.
Disconnect the yellow wire from the ground and reconnect into the molded cap.

Product Page this Question was Asked From
Air Lift WirelessAIR Compressor System for Air Helper Springs - Remote - Bluetooth
- Air Bag Compressor Kit
- Wireless Control
- Dual Path
- Digital Display
- 100 psi
- Air Lift
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Shop: Replacement Remote Control for Air Lift WirelessONE Compressor System
- Search Results: 766
- Search Results: 25980ez
- Shop: Suspension Enhancement
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Demco Stay-IN-Play Duo Flat Tow Brake System for RVs w/ Hydraulic Brakes - Proportional
- Search Results: 56070
- Shop: Firestone Air Command Extreme Duty Air Compressor with Tank - Remote and Smartphone App - Dual Path
- Search Results: 9599006
- Search Results: 6271
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: TorkLift SuperHitch Original Trailer Hitch Receiver - Custom Fit - Class V - Dual 2" Receivers
- Shop: TorkLift SuperHitch Magnum Trailer Hitch Receiver - Custom Fit - Class V - 2-1/2" and 2"
- Search Results: c3216
- Search Results: c1212
- Q&A: Troubleshooting Air Lift WirelessOne Compressor System Remote Not Pairing
- Shop: Brake Controller
- Video: Comprehensive Review: Universal Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers
- Video: Review of Redarc Trailer Brake Controller - Tow Pro Liberty Proportional Controller - RED24FR
- Q&A: The Remote Says Fail, Is There A Reset On The Air Lift WirelessAIR Compressor System
- Q&A: Pairing the Replacement Wireless Remote to the Air Lift WirelessAIR Compressor System
- Q&A: Why Is My AirLift WirelessONE Blowing the In-Line Fuse On My 2020 Ford F-350?
- Q&A: How to Pair New Remote With Air Lift WirelessAIR Compressor System
- Q&A: Air Lift Wireless Remote Control Replacement For Remote 73001 and Pairing Instructions
- Video: Hands-On with the TorkLift Cannon Hitch Extension
- Article: Trailer Wiring Diagrams
- Q&A: Troubleshooting Remote On Air Lift No Longer Joining To Manifold
- Video: Installation: Air Lift LoadLifter 5000 Air Helper Springs on a 2019 Chevrolet Silverado 2500
Greg
4/28/2020
Hi the batteries went dead in my remote thought So i replaced the batteries. The screen is still blank none of the buttons respond. Thank you