Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
Item # 13323
Retail:$250.95
Our Price: $163.56
You Save: $87.39
Confirmed to Fit
2009 Toyota Tacoma
excluding X-Runner
X-Runner
Will this fit?
To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
This item qualifies for Free Shipping
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (355)
- Q & A (0)
- Photos
2009 Toyota Tacoma - Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- 2 Inch Hitch
- Class III
- 5000
- Concealed Cross Tube
- CURT
- 500
- 5500 lbs WD GTW
- 550 lbs WD TW
- Custom Fit Hitch
This fully welded trailer hitch receiver bolts onto your Toyota Tacoma's frame with no welding required. Powder coated steel is sturdy and corrosion resistant.
Features:
- Custom fit is designed specifically for your vehicle
- Precision, robotic welding maximizes strength and improves fit
- Bolt-on installation - no welding required
- Complete hardware kit and installation instructions included
- Lifetime technical support from the experts at etrailer.com
- Gloss black powder coat finish over protective base coat offers superior rust resistance
- Sturdy, square-tube design
- Ball mount, pin and clip sold separately
- Hitch assembled in the USA, bolts overseas
Specs:
- Receiver opening: 2" x 2"
- Rating: Class III
- Maximum gross trailer weight: 5,000 lbs
- Maximum GTW when used with weight distribution: 5,500 lbs
- Maximum tongue weight: 500 lbs
- Maximum TW when used with weight distribution: 550 lbs
- Maximum gross trailer weight: 5,000 lbs
- Limited lifetime warranty
etrailer.com Technical Support
At etrailer.com we're committed to the products we sell, and to our customers. Our experienced and knowledgeable staff are available via both phone and email to address your questions and concerns for the lifetime of your hitch. The technicians at etrailer perform hitch installations on a daily basis, making them a valuable resource for do-it-yourselfers. The one-on-one, personal service you'll receive comes straight from an expert in the towing and automotive field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.
13323 Curt Class 3 Trailer Hitch Receiver
Installation Details
Weight Carrying Capacity
Gross Towing Weight (GTW):
5,000 lbs.
Tongue Weight (TW):
500 lbs.
Weight Distribution Capacity
Gross Towing Weight (GTW):
5,500 lbs.
Tongue Weight (TW):
550 lbs.
Gross Towing Weight (GTW):
5,000 lbs.
Tongue Weight (TW):
500 lbs.
Weight Distribution Capacity
Gross Towing Weight (GTW):
5,500 lbs.
Tongue Weight (TW):
550 lbs.
Tech Tip
Bumper brackets will need to be loosened and bumper supported during hitch installation. No drilling required for installation , Hitch does not fit vehicles with a factory installed hitch
Complete Towing Package for 2009 Toyota Tacoma
Retail:$378.38
Package Price:$241.01
2009 Toyota Tacoma Owners Who Purchased This Trailer Hitch Also Bought...
Popular Tacoma Trailer Hitch Accessories
Customer Satisfaction Score:
97% were satisfied with this product
3% of customers were not satisfied
- Wrong item was ordered
- Arrived Damaged
- Did not arrive in time
Customer Reviews
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" - 13323
Average Customer Rating: 4.9 out of 5 stars (355 Customer Reviews)
This fully welded trailer hitch receiver bolts onto your vehicle's frame with no welding required. Powder coated steel is sturdy and corrosion resistant.by: KEVIN MASSEY03/17/2017
2007 Toyota Tacoma
After searching for a hitch , i found this product from etrailer. This trailer hitch was very reasonably priced and the shipment was very fast. After receiving the hitch, it only took about 30 minutes to install. This product is extremely well built. The welds are excellent, and i especially like the tow hook rings. I use this truck for a landscaping trailer and fishing boat.
Great product was a great company .
THANKS
by: Ron C.07/24/2012
Excellent product and superior service! It arrived in a couple of days and
an easy install.
Here is a helpful hint. To support the bumper I used two cargo straps (the
kind with no hooks). With the tailgate open drop the non buckle end between
the tailgate and body. Close the tailgate and wrap the straps under and
around the bumper and tailgate. Tighten them and the bumper is supported
with nothing in your way! Pretty slick, see attached photos
Keithmj
1/24/2015
Thanks for the tip on keeping the bumper up. It looks like a good way to do it. I will use this way when I install mine. Did you need help holding the hitch in place?
by: Craig G10/25/2015
2015 Toyota Tacoma
I received the hitch and it looked good. I took it out the box it came in. Went to install it and noticed one of the sides was bent in, this probably happened during shipping. I used a rubbed mallet to beat the side back out to get it to fit up against the bed rails. Other than that the installation was simple and easy.
Craig G.
11/1/2016
It works well. I haven’t had any problems with it Knock on wood The only problem I had was when I first got it and it was bent a little bit but I was able to straighten it and get it on.
by: Works like a charm01/05/2014
2006 Toyota Tacoma
I installed the following on a 2006 Toyota Tacoma PreRunner. Watching all the related etrailer installation videos will give you an excellent idea of what to expect. Having an extra pair of hands removing the rear bumper and installing the hitch is a must. I admit it would have been nice to have a lift and impact wrench. ;) Otherwise pretty straight forward. The wiring harness and mounting brackets were just as simple. Again, just follow all the etrailer videos. See photo 1 for finished install. Sorry for the poor quality pic.
Works like a charm. I'm satisfied!
Side note: I used the longer receiver mounting bracket (18136) in conjunction with the 4-Pole Flat mounting bracket(18144). The wire connector is almost even with the back of the receiver tube. See photo 2.
* 13323 - Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
* 118496 - T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
* 18136 - No-Drill Mount Bracket, Long
* 18144 - Mounting Bracket 4-Pole Flat
Because I am volunteering to help pull a trailer once a month for a local charity, this particular product definitely made the project a viable solution. The great ratings on this hitch, price, and turn around time on shipping were an obvious plus. I will be keeping etrailer bookmarked for any future towing needs. Wouldn't hesitate recommending etrailer to a friend.
by: Timothy 09/16/2023
2010 Toyota Tacoma
Received the package and noticed that the contents had shifted creating a hole through the cardboard. The hitch, hardware and wiring harness appear to be ok. Until the hirch is installed i really won't know if there are any issues.
The hitch and harness look we made.
by: Scott 10/07/2023
2006 Toyota Tacoma
Excellent video installation instructions; freaky-fast delivery; solid build. Great stuff!
by: John C.01/11/2012
2012 Toyota Tacoma
When I ordered this trailer hitch for my 2012 Toyota Tacoma from etrailer.com it was expressed mailed free of charge! Three days later, there it was on my front porch! The etrailer video that explains how to install the hitch was easy to understand. Although it's recommended that two people install the hitch, I was able to do it myself using a car jack to hold one end up while I attached the other end. Total installment time by myself was 50 minutes. I was going to have a professional do the wiring, but etrailer makes it so simple that I may do that job myself at a great price!
by: Chad C.08/17/2014
Best part about this hitch is its made in the USA. It went on flawlessly and looks great. The finish is shinny powder coating and the fit is perfect. I also added a 4 pin wiring harness bracket that holds the connector up and out of sight.
by: Ryan03/26/2021
The hitch receiver was taped at the end including to wrappings of paper cardboard around the crossbar. The box was beat up really bad by UPS and resulted a few minor dings and scratches on the crossbar and receiver. Yes, UPS has some responsibility for mishandling the package but etrailer did not pack this well in my opinion.
by: Tony A.06/08/2020
The quality of this hitch is top notch. Heavy duty, sturdy and well built. The installation instructions made the project very easy to install. This product was a perfect fit and I would definitively buy from this company again. Thanks etrailer and keep up the great work.
by: Michael04/02/2013
2010 Toyota Tacoma
Exactly what I needed. This hitch and T-connect wiring kit was easy to install and looks great! I highly recommend these products and I will definitely buy from etrailer again!!
by: Bill Torres03/22/2011
Wow ..Easy Installation of Trailer Hitch..1 2 3..it was done....needed it for wheelchair lift...for my daughter who has spina bifida...need to haul her around...needed hitch for carrier...Thank you...
by: Camilo Canoa02/08/2017
Installation of this hitch was a breeze! And it can be done by one person! Instruccions were legible and clear and this hitch was cheaper than e*** or a*****! Plus backed by the guarantee im only buying my hitchs from etrailer.com!!
by: Kevin 07/22/2023
Fits like a glove! I also was replacing a rusted out bumper and the only additional pieces you may need if you are replacing an original OEM hitch, would be the left and right bumper brackets.
by: Ryan01/13/2012
2009 Toyota Tacoma
I ordered the hitch on Sunday night, and it arrived Wednesday afternoon. Installation was quick and easy, taking me just under an hour to do by myself. I'd order another hitch from and recommend etrailer.com to any of my friends.
by: Daniel S.02/05/2019
2014 Toyota Tacoma
The installation was straightforward, the instructions were very clear. I will definitely be recommending this company to my friends.
by: Ed05/31/2021
Fits like million dollar glove! Easy to install and easy to follow instructions.
by: Ken B01/17/2014
2014 Toyota Tacoma
Curt hitch fit my 2014 Tacoma perfectly .Took just under an hour to install.
by: Butch Davis10/07/2012
2007 Toyota Tacoma
There should be a rating higher than "Excellant" for the two products I bought, trailerhitch and wiring harness....
Both of these were so easy to install I was "blown away" by the ease of installation...
But I do have ONE HUGE suggestion....Either include a CD-ROM for the installations, or at least include something that says go to your web site and watch the videos. Your step-by-step video instructions were awesome. The written directions tell you to removr two bolts and loosen three and then mount the hitch, NO WAY, it's much easier to do it like your video tells you to. I took my laptop out to the garage and watched the video during the install and could pause it and do that step, pause and restart :) :) :) LOVED IT......
But I do have ONE HUGE suggestion....Either include a CD-ROM for the installations, or at least include something that says go to your web site and watch the videos. Your step-by-step video instructions were awesome. The written directions tell you to removr two bolts and loosen three and then mount the hitch, NO WAY, it's much easier to do it like your video tells you to. I took my laptop out to the garage and watched the video during the install and could pause it and do that step, pause and restart :) :) :) LOVED IT......
" />
Butch D.
4/9/2014
Loved the product, the install was so easy...........traded thetruck in on a 2014 Toyota Tacoma in November of 2013........
by: Tom Assenmacher07/18/2014
2010 Toyota Tacoma
Received the trailer hitch on time. A great product and was easily installed by me. This is my second hitch from E-Trailer (first hitch was for a 2009 Honda CRV), and the service then was great too. Highly recommend E-Trailer - and great installation instructions too!
Tom A.
7/18/2015
Great! No problems at all. Used on my 2010 Toyota Tacoma pickup to tow a 13 Casita travel trailer on a trip from Kinsale, VA to Argentia, Newfoundland Canada! A trip of about 6000 miles. The hitch was very easily installed and the instructions were very thorough. Thanks much!!
by: Hillary08/02/2023
2009 Toyota Tacoma
Our first order received was missing two of the parts ordered. Once we received the rest, the pins were missing from it. So all in all the parts are great once installed. The shipping dept. may need some improvement.
by: J.G.11/25/2016
2006 Toyota Tacoma
I bought the Kurt trailer hitch and had it installed on my Toyota Tacoma. Not a problem at all installing it. Fit right in. It has been used to take a sailboat to water five times this year. Great product!
J.g.
11/29/2017
It works perfectly well. Not a hitch forgive the pun!
by: Nic T10/19/2022
2009 Toyota Tacoma
The hitch and suggested wiring harness were a perfect fit for my 2009 Toyota Tacoma. etrailer, as always was, was great to work with. Shipping was very fast and the packaging was excellent!
Well done, etrailer!
by: Alan M.04/23/2011
Excellent paint, excellent fit, easily bolted on with a friends help, and 3 beers....didn't need to remove bumper or any cutting/welding. perfect, perfect, perfect product. start to finish was 1 hour in my driveway.
by: Tom07/19/2021
Great fit, easy install. Be sure to adjust/straighten out the bumper before tightening the bolts.
25
355
Show More Reviews
See what our Experts say about this CURT Trailer Hitch
- Comparing Draw Tite and Curt Hitch for 2006 Toyota TacomaBetween the Draw Tite # 75236 and the Curt # 13323 there isn't a significant difference in ground clearance. They both fit right up to the bottom of the rear bumper. Overall I would go with the Curt though. We have found that typically the quality control is a bit tighter on the Curt hitches and the powdercoat is a little more resilient.
view full answer... - Width of Trailer Hitch Receivers for 2005 Toyota TacomaThere are three trailer hitch receivers that are fits for a 2005 Toyota Tacoma, and according to the manufacturers, from outside-to-outside at the widest points the hitches were approximately 38-1/2 inches wide. That would be the part of the hitch that attaches to the outside of the frame rail, but as you can see from the cut out of the installation instructions, there is a flange on the inside which is about 1/2 inch from the sides. I believe this may be what you were referring to by...
view full answer...
- Recommended Hitch for 2008 Toyota Tacoma That Would Require No Modifications to VehicleThe Draw-Tite Max Frame Class III Receiver Hitch, part # 75236 will fit your 2008 Tacoma as long as the Tacoma is not the X-Runner model. If your Tacoma is the X-Runner Model, you would want to use the Curt Class III Receiver Hitch, part # 13323. Neither the Curt or the Draw-Tite model would require any modifications to the vehicle.
view full answer... - Hitch for Carrying Bike Rack for a 2013 Toyota TacomaUnless you can find a way to use all 4 mounting holes of the Curt hitch part # E-3S I can't recommend it for your application. The picture you submitted shows a set of holes that could match up to the larger holes of the hitch but nothing for the rear holes. Your best option is still going to be to use a frame mounted hitch like the part # 13323 which is a confirmed fit for your truck. The most popular bike rack we carry that has been confirmed to fit this vehicle is the Thule Camber...
view full answer...
- Install Time for Trailer Hitches for a 2014 Toyota TacomaThere really isn't any reason the Curt Hitch part # 13323 would be any harder to install than the Hidden Hitch part # 87581 or the Draw Tite Hitch part # 75236. The reason for the install time difference is because Hidden Hitch and Draw Tite are made by the same company so they rated the install time one way (the same) and Curt said it would take a bit longer. It's hard to say exactly how long it will take someone so they make their best approximation. They just happen to have picked different...
view full answer... - Determining if Hitch of 2012 Toyota Tacoma is OEM for Picking Out ReplacementYou'll have to get underneath the rear of the truck and look at how the hitch is attached to the rear truck frame. If it's bolted to the frame then it's aftermarket and a hitch like the Draw Tite # 75236 could fit and work great. If instead it's welded to the rear bumper beam or frame it would be an OEM hitch.
view full answer... - Trailer Hitch, Wiring & Related Towing Items for 2012 Toyota TacomaCurt 2-inch Class III hitch # 13323 is a confirmed no-drill hitch fit for your 2012 Toyota Tacoma. This hitch fits both X-Runner and non-X-Runner versions and it includes the hardware you'll use for its bolt-on installation into the truck's existing frame weld nuts. An installation video is linked for you. For a 4-pole trailer wiring harness you can use Curt # C55513 which is a simple plug-and-play installation with no cutting or splicing of wires required, as shown in the linked video. You...
view full answer... - Trailer Hitch Recommendation for a 2015 Toyota TacomaYes, the Curt Hitch part # 13323 that you referenced has been confirmed to fit your 2015 Toyota Tacoma so I would recommend it for you. I attached an install video for you to check out as well. If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag. If...
view full answer... - Trailer Hitch, Wiring, and Accessories for a 2013 Toyota Tacoma Doublecab PreRunnerThe Curt trailer hitch # 13323 will fit all models of the 2013 Toyota Tacoma including your PreRunner. I have included a link to a video showing a typical installation and a link to the instructions. If you plan on doing some towing I also recommend the etrailer ball mount kit # 989900. It comes with 2 ball mounts, 2 balls, a hitch pin with clip, and a storage bag. For trailer wiring use # 118496. I have linked a video and instructions for the wiring as well.
view full answer... - Trailer Hitch Availability for a 2011 Toyota TacomaYes, I checked with Curt and trailer hitch # 13323 is a fit for the 2011 Toyota Tacoma models. To wire your vehicle for towing, you would be able to use custom-fit Tow Ready wiring harness # 118496. To equip your Tacoma for towing a trailer, you would also need a ball mount, a hitch pin, and a hitch ball. The recommended ball mount for your vehicle would be # C45010, which would place the hitch ball at the most common trailer height. To determine whether this would be appropriate for...
view full answer... - Trailer Hitch Recommendation for 2014 Toyota TacomaBoth the Curt Class III Trailer Hitch # 13323 and the Draw-Tite Class III Trailer Hitch # 75236 would work well for you. These Class III trailer hitches have a 2 inch receiver, 5,000 pound max towing weight and 500 pound max tongue weight. For installation, both hitches require the bumper brackets to be loosed or removed. I would go with the Curt trailer hitch, as it is more economically friendly than Draw-Tite. The trailer hitch will bolt into existing weld nuts on your truck's frame....
view full answer... - Will the Curt Class III Trailer Hitch # 13323 Fit a 2007 Toyota Tacoma PreRunnerYes, the Curt Class III Trailer Hitch, # 13323, will fit on your 2007 Toyota Tacoma PreRunner. This hitch fits all models of the 2007 Tacoma. We had a customer install this hitch on their PreRunner model last month and commented that it works great. They did add that an extra set of hands would help raising the hitch into position. If you plan on doing some towing, I have attached a help article that will help you choose the correct ball mount for the trailer you intend to tow. If you...
view full answer... - Width of Trailer Hitch for 2006 Toyota TacomaI reached out to the manufacturer who told me the etrailer.com Trailer Hitch Receiver # E98850 was tapered at the brackets but at its widest point was approximately 38-1/2 inches. The same is true of the Curt Trailer Hitch Receiver # 13323. Both of these hitches fit a 2006 Toyota Tacoma, as will the Draw-Tite Trailer Hitch # 75236. I have added links to videos of both the Curt and Draw-Tite hitch being installed on an '06 Tacoma. Additionally, if you are looking to tow with this truck...
view full answer... - Recommended Hitch for a 2014 Toyota Tacoma w/out a Factory HitchThe etrailer Hitch item # e98850 you were looking at, is custom fit so the holes will line up on your 2014 Toyota Tacoma if you do not have a factory hitch installed. This hitch does include all of the necessary mounting hardware to complete the installation. If you have the factory hitch it must be removed and the holes will not line up. All of the aftermarket hitches for the 2014 Toyota Tacoma are the same way. As far as a video goes we only have a video of the Curt item # 13323 being...
view full answer... - How to Determine Rise or Drop for Ball MountYou're right, the information for getting everything correct is pretty overwhelming but you seem to have it down pretty well! In order to determine the correct rise or drop you need for your ball mount, all you have to do is measure from the top of your receiver to the ground and from the bottom of your trailer coupler to the ground and find the difference. You can use the cut outs of the linked help article on "How to Measure for Rise or Drop" I added. For example, the Curt Trailer Hitch...
view full answer...
- Available Custom-Fit Class III Trailer Hitch and Wiring Harness for 2014 Toyota TacomaYes, we offer two options in a 2-inch Class III custom-fit hitch for your 2014 Toyota Tacoma, the Draw-Tite # 75236 and the Curt # 13323. Both share identical weight ratings and a common no-drill installation process, which is shown in the linked video. I recommend the Draw-Tite since it currently offers a lower price. For a 4-pole wiring harness, if needed, I suggest the Tekonsha custom-fit plug-and-play harness # 118496. An install video for this is included too.
view full answer... - Trailer Hitch for 2005-2015 Toyota TacomaYes, the Curt Trailer Hitch Receiver # C13900 will fit a 2005 -2015 Toyota Tacoma. To properly install the hitch you will use the bolt holes "A" and "C" in the diagram, they will fit existing holes and doesn't require any drilling. However I have a much better option that I think you'll prefer, the Curt Trailer Hitch Receiver # 13323. It's custom fit specifically for your Toyota Tacoma so it will install a little easier and not be as much work. It also uses factory holes in the frame...
view full answer...
- Alternative to Ladder Rack for 2014 Toyota Tacoma with BAKFlip F1 Tonneau Cover InstalledNone of the ladder racks available for the 2014 Toyota Tacoma will work with a Tonneau cover installed on the bed but I do have a solution for you. Also the ladder rack for the BAKFlip CS will not fit because it is designed to attach to a special rail system which isn't available (unless BAK can offer them) and that is not on the regular F1 tonneau covers like you have. For the alternative I have in mind to work you would need to have a hitch at the front or rear of the Tacoma. Then you...
view full answer... - Towing a Trailer and Carrying Kayaks with a Rhino-Rack T-Load on a 2011 Toyota TacomaWhat you will need is a dual purpose ball mount, # D210. This ball mount has a receiver welded to the top and a ball mount on the bottom allowing you to tow a trailer and use the Rhino-Rack T-Load, # RTL002, at the same time. The ball mount is rated for 750 pounds tongue weight overall but the receiver portion is rated for 350 pounds tongue weight. The combined weight of the T-Load and the cargo cannot exceed 350 pounds. And the combined weight of the T-Load, cargo, and tongue weight...
view full answer... - Trailer Hitch and Towing Equipment for a 2013 Toyota Tacoma PrerunnerFor a 2013 Toyota Tacoma Prerunner, I'd recommend the Curt Class III Trailer Hitch, part # 13323. The hitch has a 5000 lb capacity, and is pretty simple to install. I've linked you to the installation instructions as well as to an install video that you might find helpful. The # 37042 hitch you referred to has been discontinued, but when it was available it was a fit for a first generation (2001-2007 model years). It would not be a fit for your Tacoma. Once you get a hitch installed,...
view full answer... - Recommended Adjustable Ball Mount to Allow Drop for Trailer Coupler to Ride LevelFor a 2 inch hitch like the Curt Class III # 13323, you will want to make sure you have a custom fit for your truck. If you give me the year, I am happy to assist in getting you a hitch receiver confirmed to fit properly. I recommend an adjustable ball mount so you can tow multiple trailers level. I have attached an article to assist with this whether you decide to use a fixed mount for a specific trailer or an adjustable mount to give you more options. I've linked the page to all your...
view full answer... - Trailer Hitch and Adapter Needed For 2011 Toyota Tacoma To Carry 1-1/4 Bike RackWe do have a hitch available for you 2011 Toyota Tacoma, but the only hitches available for your Tacoma are 2 Inch. For a hitch, I would recommend the item you selected, Curt Trailer Hitch, part # 13323, which is a Class III 2 Inch Hitch. If you have a bike rack that only fits 1-1/4 Inch receivers, you will need Hitch Adapter 2 to 1-1/4, part # HT02. If you use part # HT02, you will also need Pin and Clip, part # PC3, to attach to your hitch. When using an adapter, you may experience...
view full answer... - Hitch and Thule Goalpost Recommendation for a 2008 Toyota TacomaI would recommend the Curt Hitch part # 13323. This is the most popular hitch we carry that is confirmed to fit the 2008 Toyota Tacoma. Even though the capacity is more than you need it would be your best option and it would give you greater flexibility for in the future if you were to want to tow a trailer. The bumper style hitches are universal and might require some modification to fit your bumper and they have much less capacity so the custom fit # 13323 would be a better choice. I...
view full answer... - Trailer Hitch for a 2015 Toyota TacomaWe have Curt trailer hitch # 13323 as a fit for the 2015 Toyota Tacoma but none that mount just to the bumper. This is actually not bad news because bumper mount hitches are traditionally limited to 3,500 pounds gross trailer weight and 350 pounds tongue weight. The Curt frame mount hitch is rated for 5,000 pounds gross trailer weight and 500 pounds tongue weight. I have linked a video showing how the hitch installs for you. If you plan on doing some towing you might be interested in...
view full answer...
Do you have a question about this Trailer Hitch?
Info for this part was:
Test Fit:
Joe V
Test Fit:
Randy B
Test Fit:
Brent H
Expert Research:
Mike L
Expert Research:
Sarah L
Expert Research:
Robert G
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
John H
Expert Research:
Adam R
Video Edited:
Zack K
Video Edited:
Joshua S
Video Edited:
Jacob T
Video Edited:
Kathleen M
Written by:
Lindsey S
Video by:
Chris R
Updated by:
Wilson B
Updated by:
Amanda M
Updated by:
Kristina F
Updated by:
Isabelle B
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Kevin M.
4/13/2018
Thanks for the follow up. I have used this trailer hitch extensively, and it is a great product. Its also a pleasure to deal with a company that genuinely cares about its customers. You will get all my business as I need more products, and I will let all my friends know about etrailer also. Have a great day.