Customers compare 80948 to these similar products
Products Featured in this Video
Today we're going to review part number 80948. This is the Tow Ready Combo Bar with the 2 inch Trailer Hitch Receiver. Now, this is a fabrication part which is perfect for constructing an under car receiver hitch when a receiver is not available. The receiver is designed with the appropriately sized tube for an easy insertion of ball mounts. You can see it even has the pin hole drilled on the side… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
Yes, the Draw-Tite Trailer Hitch Receiver #DT45508 will fit on you 2001 Ford F-350 XL Super Duty. This will allow you to use either the 34" #RP45292 or 41" #RP45018 extension in the 2-1/2" Receiver. Do remember you will…
view full answer...The current Torklift tie down part #TLD3101 that you have installed on your 1997 Dodge Ram 3500 only fits if you have the factory hitch. If you go with the SuperHitch part #TLD1100 you would need to change your rear tie down to the part #TLR3503.
view full answer...Combo bar #80948 is used in hitch fabrication and is not technically an extender. It has no hitch pin hole to secure to the receiver on the trailer hitch. The longest regular extender that we have for a 2 inch trailer hitch is #ST18 at 18 inches…
view full answer...We do have weldable trailer hitch receivers for your 2004 Dodge Ram. The longest one is going to be 48 inches, and you can use either the Tow Ready Combo Bar with 2" Trailer Hitch Receiver #80948 or Curt Combo Bar with 2" Trailer Hitch…
view full answer...The outside dimension of the tubing that the #337RT25848B Buyer's Products Black 2 Inch Receiver Tube is constructed of is 2-1/2 inches, so theoretically speaking it would possibly fit in a 2-1/2 inch receiver. However, it will likely be a very…
view full answer...To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…
view full answer...The only other extension that will meet your 36" requirement is the Titan Hitch Box Extension for 2-1/2" Trailer Hitches, 41" - 48" Long #RP45018. This extension would have a maximum gross trailer weight of 7,500 lbs/750 lbs of…
view full answer...We don't have a 7-way splitter like the photo you sent. We instead for applications just like yours recommend using the Mighty Cord 5th Wheel/Gooseneck Wiring Harness w/ 7-Pole Connector - 7' Long #A10-7007 or the 10 foot long #A10-7010. This…
view full answer...We currently offer the Titan Hitch Box Extension part #RP45292 trailer hitch extender for a 2-1/2" receiver tube opening that will provide you with around a 24" - 34" extension. The weight capacity at the end of either extender will…
view full answer...The 3" hitches Ford is using are throwing everyone for a bit of a loop. With that being said, I do have a couple options for you to check out. First will be the TorkLift Cannon Hitch Extension - 3" Ford Super Duty Factory Hitch #TLE1636.…
view full answer...For a 48" hitch extension that fits a 3" receiver you're going to want the TorkLift Cannon Hitch Extension item #TLE1648. This hitch extender is specially designed to work with Ford's 3" factory trailer hitch. This is the only…
view full answer...I went to our warehouse to measure the actual wall thickness of the Tow Ready Combo Bar #80948 and the similar Curt #C49480, both of which are 48-inches long with a raw finish. With a digital caliper I measured the wall thickness of the Tow Ready…
view full answer...