Replaces the controlmodule for Lippert Components Ground Control 3.0 automatic leveling system (LC358590). Mounts in a compartment under the coach.Features: Replaces the controlmodule for Lippert Components Ground Control 3.0 electric leveling system (LC358590) Mounts in a compartment under the coach Connects directly to your 12-volt battery with wiring harness Other wiring harnesses connect the jack motors, rear sensor, and the touchpad to the controlmodule
Replaces the controlemodule for your Lippert Components Ground Control 2.0 electric leveling system (293977).Features: Replaces the controlmodule for your Lippert Components Ground Control 2.0 electric leveling system (293977)
Replaces the controlmodule for your Lippert 6-Point Ground Control 3.0 electric leveling system (2021106810). Compatible only with fifth-wheel RVs prepped for Ground Control 3.0.Features: Replaces the controlmodule for your Lippert 6-Point Ground Control 3.0 electric leveling system (2021106810) Compatible only with 5th-wheel RVs prepped for Ground Control 3.0 Mounts inside a front exterior storage compartment - hardware not included Connects directly to your 12-volt battery with wiring harness Fits: Part number 2021106810 , Lippert 6-Point Ground Control 3.0 leveling system for prepped fifth-wheel RVs Note: If your fifth-wheel RV is prepped for Ground Control 3.0, you will see a green prepped wire and/or indication on the exterior of your fifth-wheel RV.
Use your Gen 6 or later Hydrastar electric-over-hydraulic brake actuator with your factory Ford (model years 2007 - 2008) or Chevy (model years 2007 - current) electric trailer brake controller by installing this adapter.Brake Controller Compatibility Not all electric trailer brake controllers will work with the Hydrastar electric-over-hydraulic brake actuator. Some factory brake controllers are only compatible if used with this adapter module.
This adapter module allows you to control your Dexter Axle BrakeRite (T4813100, T4813102, T482250, or T4835700) electric-over-hydraulic brake actuator with your factory Ford, GMC, or Chevy brake controller.Features: Lets you control your Dexter Axle BrakeRite (T4813100, T4813102, T482250, or T4835700) electric-over-hydraulic actuator with your factory Ford, GMC, or Chevy brake controller Intercepts verification signals to prevent false error codes Can be mounted anywhere and splices into your BrakeRite actuator's wiring Butt connectors included Made in the USA
Replaces the 10-amp controlmodule for your Kwikee electric RV steps. Compatible with "A", "B", or "C" linkage type IMGL step motors.Features: Replaces the 10-amp controlmodule for your Kwikee electric RV steps Compatible with "A", "B", or "C" linkage type IMGL step motors Works with steps manufactured in 2019 or later Fits: Kwikee electric RV steps with "A", "B", and "C" linkage type IMGL step motors
Replaces the step controlmodule for your Lippert Components powered Tread Lite RV steps (LC353542, LC353543, LC353620, or LC353621).Features: Replaces the step controlmodule for your Lippert Components Tread Lite RV steps (LC353542, LC353543, LC353620, or LC353621) Mounting hardware not included
This replacement controlmodule is the brain that enables your single, double, or triple electric Lippert Coach Step or Stromberg Carlson sliding step to function properly. ... Features: Replaces the controlmodule that came standard on your single, double, or triple electric Lippert Coach Step or Stromberg Carlson sliding step Houses the circuits and electrical components necessary for the step to function properly Includes weatherproof wiring and connectors Installs underneath the base of your step with 4 self-tapping screws (not included)
Replace a damaged or faulty wiring harness in your Lippert electric bed lift system. This direct replacement electric drive module harness restores proper power and signal connection between the bed lift motor and control components.Features: Replaces the electric drive module wiring harness for your Lippert electric bed lift system Works with Lippert bed lift electric drive modules 236-1/4" (6000 mm) long wiring harness provides proper reach between bed lift components Restores proper power and signal connection between the drive module and bed lift components Direct replacement harness designed to install without modification Ideal solution for damaged, pinched, or worn bed lift wiring Fits: Lippert electric bed lift systems that use a standalone electric drive module and wiring harness
Automatically level and stabilize your fifth-wheel RV with this electronic leveling system. 6 Precise, motorized jacks can be operated by either the included touchpad or a Bluetooth compatible app on your smartphone.Wiring harnesses are also included that connect the jack motors, rear sensor, and the touchpad to the controlmodule.
Replace the controller in your Lippert OneControl PG In-Wall Slide system. Compatible with SlimRack and FAST Track mechanisms. Auto-program module restores smooth, synchronized travel for your motorized slide-out. ... Features: Direct replacement controller for Lippert OneControl PG In-Wall Slide systems using SlimRack or FAST Track mechanisms Auto-program controller calibrates stop points to keep your motorized slide operating smoothly Synchronizes dual slide motors for smooth, in-sync travel Works only on systems with a parking brake input Plug-and-play install with your existing OneControl harness Fits: Lippert OneControl PG In-Wall Slide systems built with SlimRack or FAST Track mechanisms
Controller Parts
Controller
Lippert
Lippert One Control PG In-Wall RV Slide-Out Systems
Automatically level and stabilize your fifth-wheel RV with this electronic leveling system. 4 Precise, motorized jacks can be operated by either the included touchpad. Hitch recognition memory function offers simple hookup.Wiring harnesses are also included that connect the jack motors, rear sensor, and the touchpad to the controlmodule.
If your RV is already prepped for the Ground Control 3.0 system, this kit has everything you will need to automatically level and stabilize it, without unneeded, duplicate components.Wiring harnesses are also included that connect the jack motors, rear sensor, and the touchpad to the controlmodule.
Automatically level and stabilize your travel trailer with this electronic leveling system. 5 Precise, motorized jacks can be operated by the included control panel or via your smart device (if RV has Wi-Fi and factory-installed OneControl system).These will be mounted in line with the center of the frame. The controlmodule for the system mounts in a compartment under the coach with included hardware. This module has a wiring harness that connects directly to your 12-volt battery.
Replace the damaged 7-way, RV-style trailer connector on your vehicle with this T-One harness. ModuLite reduces strain on wiring system. Brake controller adapter plugs in beneath your dash and lets you easily plug in your electric brake controller.This power module functions as a tail light converter to combine the brake and turn signal functions of your automobile so that they run on one wire to properly activate your trailer's tail lights.
Replace the damaged 7-way, RV-style trailer connector on your vehicle with this T-One harness. ModuLite reduces strain on wiring system. Brake controller adapter plugs in beneath your dash and lets you easily plug in your electric brake controller.This power module functions as a tail light converter to combine the brake and turn signal functions of your automobile so that they run on one wire to properly activate your trailer's tail lights.
Your trailer's wired right, but the brakes still won't fire. If your factory controller doesn't recognize your electric-over-hydraulic actuator, this adapter sends the signal it needs so the brakes activate, no rewiring required.Once installed, the system runs normally with no setup changes at the controller. Specs Application: Vehicle controllers: Select Ford, GM, and Ram factory brake controllers Compatibility: works with Deutsche Hydrapro, Hydrastar, and Dexter disc brake actuators Electrical: Voltage: 12V DC Installation type: Inline connection to actuator harness Connector type: Pre-wired leads with butt connectors Construction: Module housing: Epoxy-potted plastic Wiring: 4 color-coded 16-gauge leads Dimensions: Overall dimensions: 2-1/2" long x 1-1/2" wide x 3/4" tall Wire lead length: 6" each Application Note: Not required for vehicles with native EOH actuator compatibility.
Replaces the control touch pad for your Power Gear RV auto-leveling system. Includes the control panel and the wiring harness.Features: Replaces the control touch pad for your Power Gear RV auto-leveling system Includes the control panel and the wiring harness Specs: Overall dimensions: 5-1/8" wide x 3-5/8" tall x 3/4" thick Mounting holes center-to-center: 4-5/8" wide x 3-1/8" tall Fits: PowerGear RV auto-leveling systems
Replaces the LED light module for your Lippert electric trailer jack (LC285318).Features: Replaces the LED light module for your Lippert electric trailer jack (LC285318) Quantity: 1 LED light module
Anodized aluminum electric-hydraulic actuator with control adapter module (CAM) lets you use your Ford, Chevy, or GM factory brake controller to activate your trailer's hydraulic brakes. ... Features: Electric-over-hydraulic brake actuator activates your trailer's hydraulic brakes when you apply the brakes in your tow vehicle Factory brake controller sends signal from tow vehicle to actuator when you apply the brakes in your tow vehicle 7-Way trailer connector is needed to transmit signal from brake controllerControl adapter module (CAM) included for compatibility with your Ford, Dodge, or GM factory brake controller Easy plug and play install - no hardwiring required Improved functionality when compared with surge brake couplers Faster response time - trailer brakes are triggered when you apply brakes in tow vehicle, as opposed to when trailer pushes against hitch ball No need to manually lock out brakes when you back up Trailer brakes can be intentionally activated when you reverse Manual override on brake controller can be activated so you can engage the trailer brakes without having to apply your vehicle brakes Vented end plate releases pressure, moisture, and heat in order to protect the internal components Allows actuator to be mounted in places where most actuators would overheat Electronic, proportional pressure valve ensures that braking is smooth and effective Built-in bleeder screw lets you easily flush air out of the brake lines Durable extruded aluminum provides superior corrosion resistance Marine-grade gasket and stainless steel hardware make this ideal for marine use Compatible with any standard, 5-amp-hour-battery breakaway kit DOT compliant Unit installs on trailer frame and connects to trailer's wiring and hydraulic brake lines (sold separately) Made in the USA Specs: Application: single-, tandem-, or triple-axle trailers with disc brakes Maximum output pressure: 1,600 psi Power: 12V DC Hydraulic port size: 3/16" Dimensions: 11-3/4" long x 3" wide x 7-3/8" tall Wire configuration: Black: 12-volt power Blue: brake controller Yellow: breakaway White: ground Warranty: Actuator: 2 years Brakes and components: 1 year Note: Do not power wash the Hydrastar actuator or take it through a commercial car wash.
Anodized aluminum electric-hydraulic actuator with control adapter module (CAM) lets you use your Ford, Chevy, or GM factory brake controller to activate your trailer's hydraulic drum brakes. ... Features: Electric-over-hydraulic brake actuator activates your trailer's hydraulic brakes when you apply the brakes in your tow vehicle Factory brake controller sends signal from tow vehicle to actuator when you apply the brakes in your tow vehicle 7-Way trailer connector (sold separately) is needed to transmit signal from brake controllerControl adapter module (CAM) included for compatibility with your Ford, Dodge, or GM factory brake controller Easy plug and play install - no hardwiring required Improved functionality when compared with surge brake couplers Faster response time - trailer brakes are triggered when you apply brakes in tow vehicle, as opposed to when trailer pushes against hitch ball No need to manually lock out brakes when you back up Trailer brakes can be intentionally activated when you reverse Manual override on brake controller can be activated so you can engage the trailer brakes without having to apply your vehicle brakes Vented end plate releases pressure, moisture, and heat in order to protect the internal components Allows actuator to be mounted in places where most actuators would overheat Electronic, proportional pressure valve ensures that braking is smooth and effective Built-in bleeder screw lets you easily flush air out of the brake lines Durable extruded aluminum provides superior corrosion resistance Marine-grade gasket and stainless steel hardware make this ideal for marine use Compatible with any standard, 5-amp-hour-battery breakaway kit (sold separately) DOT compliant Unit installs on trailer frame and connects to trailer's wiring and hydraulic brake lines (sold separately) Made in the USA Specs: Application: single-, tandem-, or triple-axle trailers with drum brakes Maximum output pressure: 1,000 psi Power: 12V DC Hydraulic port size: 3/16" Dimensions: 11-3/4" long x 3" wide x 7-3/8" tall Wire configuration: Black: 12-volt power Blue: brake controller Yellow: breakaway White: ground Warranty: Actuator: 2 years Brakes and components: 1 year Note: Do not power wash the Hydrastar actuator or take it through a commercial car wash.
Replaces leveling control panel with amp connector for your Lippert Components 4-point leveling system.Features: Replaces the leveling control panel with amp connector for your Lippert Components 4-point leveling system Wiring harness (LC178278 - sold separately) might be required with older systems Quantity: 1 control panel
Replaces the slide-out or leveling control panel for your Lippert 4-point leveling system.Features: Replaces the slide-out or leveling control brain for your Lippert 4-point leveling system Quantity: 1 replacement control brain Fits: All Lippert 4-point leveling systems Notes: Chassis harness (PN 690235) is also required when replacing controller part numbers 175226 and 67758 Adaptor harness (PN 2021127668) is required for replacement on diesel coaches Not compatible with motorized units with bi-directional pumps
Filters
