Result:

This item is listed as a confirmed fit for my 1995 Ranger. Since it does not have a converter, as some other trailer wire harnesses have, is any additional wiring or splicing required? My Ranger has the original tailight connectors to tap in...

I have a 95 ford ranger3.0 v6 rwd it doesnt have a towing kit from factory but can tow 2750lbs. I am going to be towing a 1700-2000 lb trailer on long trips,high way speed while very cold temp outside. after i get the receiver and wiring installed...

Clockwiseinch and counterclockwiseinch are meaningless without context. My existing handlesfoot locks rotate both ways. You state the lock rotates counterclockwise. Does this mean the lock cylinder is turned by the key counterclockwise to...

Reese 51032 hitch - replacement hardware I am looking at a local hitch that was never installed. I dont see this model listed here on Etrailer, but I will need a hardware kit. Can you assist? | Hey Todd, we never carried that hitch but we...

I want to get a pop up camper. I got a hitch for my own car 2005 Ford Taurus but want to be able to put it on my brothers truck, a 1995 Ford Ranger, also. There's a ball opening on the bumper. Does that mean it comes equipped with the hitch...

What all parts do I need to flat tow a 95 ford ranger? Thanks | The first thing you need to flat tow your 1995 Ford Ranger is a base plate kit like the Blue Ox part # BX2117. In addition to the base plates, you will also need a compatible...

I want to buy a curt hitch for my 1995 ford ranger but want to know if I will have any issues with the spare tire. I have read that some people say that you need to remove the full size spare tire to have clearance for the hitch. Is this true?...

I know that the problem is with the wiring harness. I was wondering if I cut the black box off and connected the wires together would this fix the problem where I have lights again for my trailer? | To determine definitively if the converter...

would like to know which extang replacement platinum cover will fit a 1995 ford ranger xlt 6 ft bed | Hey Shawn, for your 1995 Ford Ranger XLT with a 6' bed you'll want the Replacement Tarp for Extang Classic Platinum Roll-up Soft Tonneau Cover...

I have the 1995 Ranger either PU or Splash, not sure. I have a contractors metal canopy on back which weights about 275 to 300 lbs. I put rear half of bolt-on helper springs to raise rear-end about 1-1/2 inches. I pull a trailer with a tougne...

I am looking for camper tie-downs for my 1995 Ford Ranger 3.0 extended cab, 2-door, 6 foot bed, non-step side. I am looking at a Travel Lite 690fd, slide in cab-over camper, empty weight 1100#s. I am considering the Brophy Clamp on tie-downs...

almost got rear ended. I have used several trailer and several converters with green lights that show no problems , but the problem is the 1995 ford ranger with amber turn signals!!! HELP my life and wife and children say THAX for any assistance....

I have a class III hitch for a scooter lift on my 1995 Ford Ranger and the lift scrapes the street when getting out of driveway or on steep inclines. Would this adapter work on my class III hitch and would it hold the scooter and lift? large...

I have a hard plastic bedliner covering my stake pockets. If I cut out the around the stake pockets will I be able to install and use these adequately? | The Erickson Retractable Tie-Down Anchors for Truck Bed Stake Pockets # EM01003 will work...

I have a 1995 ford ranger with a 4 cyl engine, I want to install an electric radiator fan, however do not know which one would work best. The 14 1250 will fit but is it to much fan for the vehicle? At this time my truck gets only 15mpg if I...

I plan to purchase p3 brake control. i own a 1995 ford ranger xlt and i dont see a connector under my rear bumper for tow equipment. i need to install a 7 pin socket connector. Aside from the p3 brake control, can you give me a list of all...