Result: Tongue Box

on the pickup box. I believe the sidewinder, changing the pivot point making the fifth wheel tongue stationary | I have a 2017 F350 dually long bed. It sets up a bit to high for the fifth wheel to set level...

Andersen hitch. These gooseneck pin boxes are bolt pattern and tongue weight range specific so we'd first | I have a 22 Chevy 3500 SRW, towing a 15k GVWR Solitude 5th wheel, currently using an Andersen Ultimate...

Hello, I have connected all of my wire into the junction box. I do have trailer brakes and inside | Hello, I have connected all of my wire into the junction box. I do have trailer brakes and inside the tongue and there is...

building a trailer and i am capping it off at about 11K, the axle under it is a out of a old box truck | I am looking for a surge brake actuator and am having trouble deciding what one I need. I am building a trailer and...

to trailer into junction box on trailer tongue. I Think I did it right? Also dont use trailer much it’s | Single axle cargo trailer brakes don’t lock up anymore I noticed after I put on new 7plug tow wire...

Hi Doug, If the tongue really is C-Channel and not a box the you'd likely need to first weld | I have an Atwood 82541 weld on actuator with a bad master cylinder drum brakes w/lockout. The trailer tongue...

With your camper running about 10 inches lower in the back, you have the tongue of your trailer | I have open range camper that is about 10 inch lower in the back what can i do to run level | With your camper running about 10...

itself be mounting inside a trailer tongue box or does it need to be exposed to air for cooling proposes | To start I have a 2015 Chevy Silverado 2500 with integrated brake controller. I am looking to convert...

I have a Fulton A60 with a breakaway tongue on a 2007 dual axle boat trailer. Any suggestions | I have a Fulton A60 with a breakaway tongue on a 2007 dual axle boat trailer. Any suggestions for a replacement actuator? The brakes...

tongue and as low to the ground as possible and enough room to put a shield between the box and the tires | I want to build a wood fired only BBQ pit on a single axle. It will be 4foot X 6foot X 16 I have need...

buddy surge tongue is there but no discs or drums on it. When pulling it with my truck I can barely | I have a 2010 triton bass boat and trailer. When I bought it I noticed it had no brakes trailer buddy surge tongue is there...

that will use the Model 6s bolt holes. The tongue is 3x3 galvanized steel and I would prefer to not drill new | Hi there, I need to replace the Titan Model 6 surge brake actuator on my 7000lb GVWR aluminum boat trailer. The...

tongue and give you a junction box to make all of the wiring connections. You will need # 10-1-1 to go | I have an m416 trailer and would like to get your recommendation on an axle with the ability to install...

a replacement unit fit inside the square box of the GDC 80 or will I have to cut it off and re weld | I have a GDC Global Direct 80 Actuator on my 2001 Cobalt 240 Trailer. The outer housing is welded to the Y front portion...

1755000 which is made to be welded to a 3" wide trailer tongue. There are also bolt-on options like | Hi, I’m converting my 10k gross flat bed trailer from hydraulic brakes to electric. I see the backing plate kits and I’d like...

. The total length of the rear square box section before the I-Beam frame starts to bend into the tounge is 65 | Hello, I have quite a dilemma. I bought a used boat that came with a new custom aluminum I-beam trailer for the...

of the metal. My trailer tongue that this needs to slide into is 2 5/8 wide. | Hello, I need to find out how wide the DX 39FR assembly is. Your sales team says it’s 2 inches wide, but that can’t be true if it fits over a 2...

thought is to move pin box up last 2 holes to lower front-what is max nose down to consider. could | hi multiple question, have a 2005 sierra duramax dually when pulling or new 2019 hideout 281dbs 32foot 5th back from dealer...

-mm hitch balls and is a bolt-on for 3 inch wide trailer tongues. The breakaway kit is included | Surge brake actuator for drum brakes with electric back up actuator. I see you have a Titan one but it seems for disc brakes...

, Junction Box # 3430001-JBK, and 7-Way # H20046. You may also need a Flexible Brake Line # T0980100 | I have a dual axle trailer that has surge brakes on one axle. I am wanting to install electric over hydraulic brakes on the...

not already have electric trailer brakes you will also need to add a 7-way connector # H20046 and junction box | Please quote on: 1 - 2000-2200 lbs Timbren axleless set up with Disk Brakes and 5 on 5 hubs for Overlanding use...

is the Tekonsha Plug-In Wiring Adapter, part # 3051-P. This simply plugs into the junction box behind the truck | I have a 1997 Eagle tri-axle boat trailer with surge drum brakes. I want to convert it to an EOH/drum system....

Box # HS381-9000 to keep everything organized. Don't forget a breakaway kit like part # 20099 as well | I have a 20 runabout on a TrailerRight trailer with hydrolic surge brakes. Id like to convert to electric brakes. Is this...

low tongue weight (TW). Car hauler trailers, especially when they are towing different vehicles all | I Have a car transport trailer currently single axle with leaf spring suspension and drum brakes operated by a cable. I am...