Result: knobs

The Master Lock Electric Trailer Winch, # 2953AT, has a clutch knob on the side of the winch. You will need to loosen the knob in order to allow the winch to free spool. | how do we pull out cable from spool...

Once you have selected your combination numbers, turn the knob back to the original position in a counterclockwise direction. | how do you set the combination? | I went out into our warehouse and pulled a Master Lock Quantum...

Basically, the brake will always be applied when powering in and will only be released when you activate the freespooling clutch knob to let the cable out. | Does this winch have a brake for trailering aboat on trailer?. Does...

Will the 3794DAT fit this hitch considering the little half-round wall thing in front of the twist knob? | Attached is a photo of the hitch on the trailer Im going to rent. It will be parked at a friends house for the weekend...

All other hardware (bolts, nuts, knobs, etc.) would have to be either purchased through Brophy or if it's not too damaged you can take it your local hardware store to find replacements for much cheaper than going through a manufacturer and paying for shipping. |

Is there anyway to temporarily lock this hand nut Knob M6 Low on the M6 carriage bolt of the 593 Wheel-ON Wheel Carrier to prevent theft of the carrier from the car roof? | Is there anyway to temporarily lock this hand nut...

Also, you can position this bracket a couple of different ways so you can have the knobs pointed in different directions depending on how the bracket is oriented. | I have a 2016 Jeep Wrangler with a Mopar Trailer hitch? Will...

You cannot put a shank adapter like the # 853-7489 on the # TH23JV because of the locking knob system that keeps the shank firmly in place in the shank when installed. | Does this work to adapt a 1.25 T2 Pro XTR? Item TH83JV...

This is a power load in only winch, and has a clutch knob that allows freewheeling out for the cable. | I have a 1987 Dodge Pickup and a Ranger Trail boat trailer. I will use this to load 18foot Ranger Bass Boat. Does this...

If your rack uses a standard hitch pin or a threaded hitch pin this should work well for you, but if it uses a different style of attachment like a tightening knob that pins the rack into the hitch this probably wouldn't work well. |

The Apex XT has a SnugTite so you can install and remove the rack simply by turning the knob, and at 35 lbs is 8 lbs lighter than the Curt # C18065. | Is this hitch rack quick and easy to install and remove? It would not stay...

Maybe Im not understanding how these mast-type bike locks work, but it appears to me from the video that all a thief would need to do is to loosen the knobs on the wheel cradles, slide the wheel cradles backwards thus freeing the tires, shift the tires slightly to the side off the cross-bar upon which the wheel cradles are mounted, and then lower the bike to the ground to make off with your bike. |

When the bike rack is fully ed into the Draw-Tite receiver on my 2016 Subaru Outback the knob to release the swing arm hits the bumper. The Draw-Tite has two holes. | When the bike rack is fully ed into the Draw-Tite receiver...

This unit can produce 144 gallons of hot water an hour and has a thermostat that will allow you to change the temperature by the degree instead of just a knob with an arrow saying hotter or colder on it. | Hi, I am looking...

This rack allows for tool free installation, if you turn the knob you tighten the rack in the hitch receiver and eliminate any movement between the rack and your hitch receiver. | I have a 2018 Jeep Wrangler and just had a...

The NV 2.0 can be tilted down - even with the bikes loaded - with the press of a handy foot lever; it does not require any tools to install into your hitch as you'll only need to turn a knob to tighten the shank in the hitch and this also works as an anti-rattle device for a quiet ride. |

We used to carry the Yakima SwingDaddy that you mentioned and it had a distance of 6 inches from it's pin hole to the back of the knob for the swing mechanism. So you'd most likely have some contact there. | Weve got a hitch...

If you are thinking about going that route, I highly recommend taking a look at the Kuat Beta # B202-114 which weighs less than 13 lbs and has dual-strap cradles along with an anti-rattle hand knob. When using a hanging rack it's possible you'll need a bike frame adapter bar, # 64005, if your bike is dual-suspension, has a step-through frame or you want to carry a small children's bike. |

You also cannot use a latch style pin lock like part # e98887 on the knob latching mechanism but you can use a surround lock like part # ML389DAT. | I need to change my boat trailer brake actuator. You sell Titan and Demco....