Result:

Weird questions: is 10inch the inner diameter of the drums? Im trying to engineer a retrofit to a Volkswagen Vanagon being cut down to a single axle trailer. Id like to use the original VW bearings, hubs, and drums which have an inner diameter...

how much do i torque in 1998 trailer hitcth on a 1998 Ford Ranger | If you check out the installation instructions link I attached to the right you will see the recommended torque specs listed in the last step for the Curt hitch part # 13138. |

Greetings! I need your entire crew to come to my house and help me move! If that is not an option how about confirming this will fit my 1998 Ford Ranger. It is the short bed with the side steps like a Slash but it is not a Splash. 3.0L V6...

I know this cover is for a 6 foot bed. What is the width of the bed cover? It should be approximately 4 feet, correct? | Hello Tracy, thanks for reaching out. The Pace Edwards JackRabbit Retractable Hard Tonneau Cover w Explorer Rails # 311-JEF0908...

I would like to put a roof top tent on my 1998 Ranger flare side. I looking am looking at the Thule Xsporter Pro Mid Overland Truck Bed Rack - Aluminum - 600 lbs TH34RR will this work? If not what is a better option? The picture below is my...

Hello, our AVAIL8422 plow just arrived. Hooking it to a 1998 Ford Ranger. Looks like I will also need a light kit as it will block my headlights, what is a good kit to use? | K2 recommends that their # K281488LB2 Halogen High/Low Beam Light...

I would like to add brakes to a ShoreLander PT2321A pontoon trailer. What parts would I need. The trailer currently has no brakes of any kind. Thanks for the help. Here are the trailer specs: Minimum Hull Length: 240 Inches Maximum...

How 2 replace Schrader value on airlift systems | You can use the Replacement Air Line Kit for Air Lift AirLift 1000 - Rear # AL22007 you asked from or # F2012 to get a new Schrader valve, but it sounds like you just need the valve. I recommend...

How does this unit install? Does it fit and lock under my tailgate handle? Do I have to dis-assemble my tailgate handle to install it? Let me know exactly how it installs. Thank you Pop & Lock for 1998 Ford Ranger w/ steel handle - | Pop & Lock...

Have a 1998 ford range, vehicle lights all working fine. Vehicle equipped with factory tow harness receptacle. When connected to trailer only right side works fine running brake turn and flasher and on left side only running lights. Trailers...

Hello, I was just wondering what rear mounting hitch would fit onto my 1998 Ford Ranger. I recently replaced the rear bumper with a Westin FEY Diamond Step bumper part #66000 if that makes any difference as to what models will fit. Thanks,...

Please help me, I need a brake controller and hopefully a wiring adapter for a 1998 Ford Ranger 4.0 liter engine, 4x4 Xlt ext cab truck, I am pulling a 17ft camper weighing 2750 dry weight. I am almost sure it has the towing package, It...

My question is concerning a M416 military trailer. My intention are to change the hub and drum to get a 5x5 bold pattern. Thanks for your help! | Thanks for the picture! To determine the correct replacement hub to give your M416 military trailer...

I have a 1998 Ford Ranger XLT 2 wheel drive my question is will it fit and would I have to drill any holes? Thank You for any info.!!! | The Curt Hitch part # 13138 that you referenced has been confirmed as a fit for your 1998 Ford Ranger so...

Im looking to purchase a Kats Heaters Lower Radiator Hose Heater but I see that the thermostat is set at 279 degrees. Since water boils at 212 degrees, wouldnt this over heat the coolant? Thanks | The Kat's Heaters Lower Radiator Hose Heater...

How can I convert this so it works properly. I have a 1998 ford ranger and it has a 4-way round connector. I can easily rewire a flat connector being most converters I see have that. Will everything work properly? The trailer is a 1984 Mallard...

I have 1998 Ford Ranger metal handle. I purchased PAL2300 trying to install but diagram to small please help me | The # PAL2300 is indeed the correct locking replacement tailgate handle for your Ranger. I have provided a blow up of the diagrams...

when I remove the waste master hose for storage I need a cap to close end of hose. I also would like to have a better solution than little red stopper on exit end. I know I have the shut off but once as I was unpacking hose the shut off got...

Are a 1998 Ford Ranger and 2006 Expedition King Ranch both with 4 pin trailer connectors pre-wired for a 7 pin connector? If yes, do you sell the 7 pin pigtail? | The 1998 Ford Ranger is not pre-wired for a 7-way. You can convert your 4-pole...

Does this cover fit a 1998 Ford Ranger Step-side, 2 wheel drive Splashbox? What is the #8740 alternate mentioned and what are the differences between the two? I want to make sure I get the right one. Will it hold up under snow and ice? Is the...

I was wondering if you carry a reese hitch for a 98 ford ranger flareside? | Reese and Draw-Tite are the same. Same parent company, design, everything but the sticker. I recommend Draw-Tite trailer hitch # 75082 for your 1998 Ford Ranger Flareside....

I an wondering what wire I need to connect into for the feed when the brake pedal is depressed. It is in a 1998 Chevy Silverado. I have everything set up but that wire. I could not see where the wires where to connect into it. | For your 1998...

a grease seal just blew out on my new ez lube axle. to replace it, do I need to take all the bearings out? or, can i just take the hub off and put in a new seal from the back of the hub? Thanks | The bearings for your trailer hub don't need...

Draw-Tite #75058 what does it fit? i bought it today for my ranger but nw it seems too big... | I spoke to my contact at Draw Tite and the hitch part number 75090 that you referenced has long been discontinued but it was a fit for Explorers,...