Brake Controller Installation on a 1998 Ford Expedition
I plan to install a brake controller on a 1998 Ford Expedition with a tow package and a 4 pole trailer connector. I intend to purchase the following items for the installation: Item nos. 3035-P, 37185 and the 90885 controller. Is there anything...
Compatibility of Edge Evolution CTS2 EP85450 with 1998 Ford Expedition
I was told this chip would work for my 1998 ford expedition v-8 5.4 l triton is this true... | The Edge Products Evolution CTS3 Programmer/Monitor, part # EP49YR is not compatible with your 1998 Ford Expedition. I have confirmed this through...
Recommendation of Front Mount Hitch Receiver on a 1998 Ford Expedition 4-Wheel Drive for a Snow Plow
Im looking to buy a front receiver hitch foe my 98 ford expedition 4 wheel drive with factory tow hooks. you have 2 models, a Curt and a Drawtite. in your opinion what one is the best. I intend to use it for a snow plow. Thanks for your...
Correct Front Mount Trailer Hitch for 1998 Ford Expedition 4WD with Factory Tow Hooks
will the part #31049 fit the 31 3/4 inch wide with 3inch spaced holes to anchor where the tow hooks go? | The Curt Front Mount Trailer Hitch Receiver part # 31049 is a confirmed fit for a 1998 Ford Expedition 4WD with factory tow hooks. It mounts...
Wiring a 7-Way Trailer Connector and Brake Controller on a 1998 Ford Expedition
I want to connect a 7 pin to my 98 Ford Expedition. I found the connector under the dash, next to the computer diagnostic port. Where underneath the rear of the vehicle would I find the connection for the 7 pin? Thanks | There are three different...
Programmer Recommendations for a 1998 Ford Expedition with 5.4 Liter V8 Motor
What would you recommend for a 1989 ford expedition 5.4l | You typed 1989 Ford Expedition but the first model year was a 1997 so I assume you meant 1998. Which is good because there are programmer options for the 1998 Ford Expedition. For...
Is the Illumination Wire on a 1998 Ford Expedition Needed to Install a Brake Controller
1998 ford expedition. Has wire from factory for illumination. Where do I connect to on controller? Or leave it off. | The illumination wire on your 1998 Ford Expedition will not be used with a brake controller such as # 39510 (or any of the...
Which Brake Controller and Wiring Adapter Is Best for a 1998 Ford Expedition
I am looking to purchase a brake control for my RV setup. I own a 1998 Ford Expedition 5.4 V-8. It came with the trailer tow package, so it has the plug under the dash. I tow a 2006 K-Z JAG 20J 20foot trailer approx 3,500lbs. Can you recommend...
Tow Package Fuse Locations for a 1998 Ford Expedition
where is the fuse location for my 1998 ford expedition tox package plug. nothing is working | I pulled up a picture of a fuse box of a 1998 Ford Expedition and it looks like position 1 is the trailer tow running lamp relay and back up light...
Are Westin Lighted Running Boards Replacements for 1998 Ford Expedition Factory Running Boards
Hello Can you tell me if the Westin 1998 Ford Expedition Westin Molded, Lighted Running Boards w/ Custom Installation Kit - 6inch Wide - Black, Code: 27-0015-1815 are: A direct replacement for factory installed lighted running boards for...
Does Brake Controller Need to be Turned Down When Not in Use on Vehicle
I just purchased a 98 ford expedition with a draw-tite activator on it. I dont do any type of towing. so where should I position the slide button, so it wont cause me a braking problem ? tthanks |...
Which Locks Can I Use with a Yakima Sweetroll Kayak Carrier
what key locks are for the Sweetroll kayak carrier rear loading Y04074 | The Yakima Sweetroll Kayak Carrier # Y04074 does not come with lock cores but you can add them with the Yakima Same Key System (SKS) Lock Cores # Y07204 (pack of 4). If...
Installation of Brake Controller on 1998 Ford Expedition
1998 ford expedition wiring harness for prodigy brake controller | The correct Brake Controller Wiring Adapter for your 1998 Expedition would be part # 3035-P. If your Expedition has the factory equipped 7-way trailer connector as most do,...
How to Install a 7-Way Trailer Connector on a 1998 Ford Expedition with 4-Way
I have a 1998 Ford expedition without factory trailer tow. I have a aftermarket hitch with a functional 4 way flat plug. I also have a brake controller. I have a circuit tester so do not need that to be included but would like a bracket to mount...
Will Rooftop Bike Carrier, # S64720, Fit on a 1998 Ford Expedition
Does it fit 1998 Ford Expedition? | The Rooftop Bike Carrier, # S64720, will fit on Thule, Yakima, and most factory roof rack load bars that run side to side on the top of the vehicle. If you do not have a factory roof rack you can add a roof...
Towing Mirror for 1998 Ford Expedition Eddie Bauer Edition with Turn Signals in the Mirror
Will these fit out Eddie Bauer 1998 expedition? It have the turn signals in the mirrors ! | We have not tested the Custom Towing Mirrors, # CTM2300, on a 1998 Ford Expedition Eddie Bauer Edition with turn signals in the mirror. I made a call...
Replacement Bull Bar Brackets for 1998 Ford Expedition
Bull bar brackets for 98 ford expedition? | If you have the Westin Bull Bar # 32-0245 or # 32-0240, then you will want the Replacement Bracket Kit for Westin Bull Bar 32-0240 # 32-024PK. Bull Bars are not a universal fit, so you will need to...
Availability of Class IV Hitch for 1998 Ford Expedition
I have a 98 Ford expedition xlt 4x4 with 17inch tires. Is there a class iv hitch I can put on it. I plan on hauling a 6x10 dual axle dump trailer. | The highest capacity hitch available for the 1998 Expedition is the Curt # C13049. The hitch...
Grille Guard Recommendation for a 1998 Ford Expedition
I have bull bar Westin bot not have The mounting hardware for ford Expedition 1998 I need mounting bracket | The Westin Bull Bars and their mounting kits are both made to fit specific vehicles. If the bull bar you have is either part # 32-0245...
How Does the Curt Stabilization Strap Work for a Curt Hitch and 1998 Ford Expedition
Hello, When it says 2inch hitch does that mean inside opening of hitch is 2inch to receive a bike rack or motorcycle carrier ? Curt states load must be supported ? Do they mean tie down web belts to hold load or support for the carrier ? If...
Troubleshooting Trailer Wiring Harness for Class C Motorhome on 1998 Ford E350 Van Cutaway Chassis
I do not know if I have a harness presently on my motorhome. There is a 4 pin connector installed to go to the trailer harness but dont work. I cant get any electrical current to the 4 pin connector ? | I would first spend a few minutes trying...
Filter Your Search
Contact and Help