Installing Tekonsha Voyager Brkae Controller in 2013 Nissan Xterra S
I just purchased a 2013 Nissan Xterra S. The dealer installed a class c hitch with 6/7 pin wiring. They removed my Tekonsha Voyager from my old vehicle but cut off the plug. Which harness and Voyager replacement plug do I need to buy to install...
Will Rhino-Rack Locking Ski/Snowboard Carrier # RR576 Fit Factory Crossbars on 2004 Nissan Xterra
hello. i have a 2004 nissan xterra with factory crossbars that are rather big large oval like. will this product fit w/o any other modifications/parts needed? thanks mucho! | The Rhino-Rack Locking Ski and Snowboard Carrier # RR576 is intended...
Roof Mount Cargo Box for a 2006 Nissan Xterra with Factory Roof Rack
I have a 2006 Nissan Xterra with roof mounted rack and flat crossbars. Which cargo box will fit and what do I need to mount it? Thanks for your help. | The Thule Sidekick cargo box is not a fit for the factory roof rack on your 2006 Nissan...
How to Carry Kayak & Cargo on 2015 Nissan Xterra
Hi, Im heading to Alaska, and Im trying to find a good roof storage bag or hard case and a single kayak mount option using the stock Xterra roof rack. Any suggestions? Thanks | Appreciate the photo of your 2015 Nissan Xterra (not to mention...
What Carriage Bolts and Nuts do I Need for the Yakima SnapAround SNARs
Hi I have 8810135 Yakima SnapAround Mounting Brackets SNARs - Round and Square QTY 4 Item # Y8810135. I need the carriage bolts and nuts. Where can I buy. Please provide me link and part number. | While I do not have them available for purchase...
Recommended Hitch for 2013 Nissan Xterra Used for Carrying Bike Rack
Need receiver hitch for 2013 Nissan Xterra Bike rack only..not towing Need recommended products Thanks! | I recommend using the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # 13514 because of the durable powder coating that Curt...
How to Use the Thule Hullavator on a 2011 Nissan Xterra
Can a Thule Hullavator be installed on a 2011 Nissan Xterra? | The Thule Hullavator kayak carrier part # TH898 can only install on aftermarket roof racks that have bars that extend past the feet of the rack by at least 4 inches. For that you...
Replacement Hardware Needed for Reese Trailer Hitch on a 2012 Nissan Xterra
I need the two bolts with washer that come with the reese hitch for a 2012 nissian xterra. Part # | To get replacement hardware for the Reese trailer hitch on your 2012 Nissan Xterra you can use the part # RHK. This will give you all of the...
Is AirBed XUV 341031 a Good Fit for a 2008 Nissan Xterra
Hi, Will this air mattress be a good fit for a 2008 Nissan XTerra? | Yes the AirBed XUV part # 341031 that you referenced is a great fit for your 2008 Nissan Xterra. This would be a great choice that's comfortable, comes with a pump, and is...
Recommended Trailer Wiring Harness For 2011 Nissan Xterra
I am interested in buying a vehicle wiring package to be used when pulling trailer. I have a 2011 Nissan Xterra Pro 4X. I noticed that there are 4 pin and 7 pin wiring harnesses that can be used. Is there an easy way to tell if I need a 4...
Recommended Weight Distribution System for 2007 Nissan Xterra Pulling 16FT Shasta Aeroflyte Reissue
I cant figure out which system to buy. The trailer wt is 2430lb The tongue wt was measured at 410. which I dont understand that. weighed by someone else, in a nontraditional way I guess. they used a scale they use for weighing pipeline stuff....
Will Thule SnowPack Ski/Snowboard Carrier # TH7324 Fit Factory Crossbars of 2012 Nissan Xterra
Will the Thule 724 fit on the original factory crossbars of a 2012 Nissan Xterra? | Yes, the Thule SnowPack Ski/Snowboard Carrier # TH7324 will fit the factory crossbars on your 2012 Nissan Xterra. I confirmed compatibility with Thule. This...
Could a 2001 Nissan Xterra have a 4-Way Hardwired to it Using Trailer Connector Port
I need to add a 4 pin trailer wiring harness but I dont have time to get a plug in shipped. It has the tow package connector. If I hard wire a kit, do I need to use a convertor? There are 6 wires going in but only 4 will come out. How do...
Dexter EZ Flex Cushioned Equalizer for Trailer with 4,500 lb Axles
I am looking to upgrade the suspension on my small 4,500# tandem trailer with a Dexter ez flex # K71-652-00 solution. The axle to axle spacing is 28 1/2 and springs are 1 3/4 wide and measure 21 eye to eye. The present triangular trunion castings...
800 Pound Spring Bars for a Fastway E2 Weight Distribution System
I have a trailer camper,, 17 feets,,,,, 22 from bumper to front fully loaded its at 3600 pounds with a tounge weight of 667,,,,, no fresh water in the trailer,,, the tank is near the hitch i had e2 450 hitch 4500 trailer weight i was wondering...
Fit of Cipa Deluxe Door Mount Mirror # 11650 on Nissan Xterra
Hi.,..will the CIPA 11650 mirrors work well on our Xterra? Will it give enough clearence to see down the side of a 24 ft. RV? Thanks | As long as you do not have the body cladding (plastic trim pieces that add to the thickness of the door)...
Troubleshooting a 5E Error Message on a Hopkins Reliance Trailer Brake Controller
I have a 47285 brake controller installed on a 2011 jeep wrangler. I keep getting a error message thats SE or 5E. I read on some of the QandA that the red wire was in wrong place. I have checked my brake light switch and it is on the cold lead,...
7 Way Trailer Plug Will Not Stay Seated In the Vehicle 7 Way
Why does my 7 pin connector plug fall out while driving? There is enough slack in the line. It is new as of February when we bought the new RV. I lose trailer brakes when that happens. | This can be caused by a few things, but as you have enough...
Adding a Brake Controller to a 2006 Nissan Xterra with 4-Way Trailer Connector
I own a tekonsha P3 brake controller. I purchased a 2006 Xterra and would like to install brake controller. The Xterra currently has an after market hitch and 4 way flat trailer light connector installed. The 4 way appears to plug directly...
How to Wire 4-Pole Connector on Trailer Has Extra Running Light Circuit
My 2008 Nissan Xterra plug has 4 wires going into it. The current trailer wire kit has 5 coming out of it but I just bought a new wire kit to redo the trailer. The new trailer kit only has 4 wires....how do I run this? My buddy said the ground...
Lowering 2 Inch Trailer Hitch Receiver when Using a Motorcycle Rack
Id like to lower my receiver by 8inch for when I want to use a motorcycle rack. What product can you suggest? Ive seen 2 parts from Curt that look like they might work...replacement shank and multi-ball adjustable ball mount receiver. Am...
Recommended Ball Mount with Drop for Towing and Receiver for Other Accessory
Do they make one with a 4 inch drop. My xterra sits high and i normally use a 4 inch hitch for my popup | The Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers # D210 does not come in any other drop. If you need...
Why Wont the Magnaflow CatBack # MF15583 fit Nissan Xterras with Factory Hitch
hey can you tell me why the above-mentioned magnaflow exhaust system will not fit on 2011 up Nissan Xterra for Pro X or actually any of them with the factory trailer hitch I want to put the exhaust system on but it says every place I try to...
Does Curt Trailer Hitch 13514 Come with Installation Hardware for a 2011 Nissan Xterra
Does this come with all mounting hardware required? | Yes, the Curt trailer hitch # 13514 includes all of the necessary hardware for installation. I have linked the instructions and a video showing a typical installation for you. If you plan...
Filter Your Search
Contact and Help