!Stampede Travel Trailer  x   >   !1988  x   >   !Forza Motorhome  x   >   Ultra-Fab Products  x   >  

looking for complete 5th wheel landing gear the only number can find is on lift leg grease cover over the gears. model number maybe VMC900R-064362, 2004 jayco eagle 32 foot 13000 lbs | I do have a couple of solutions for you that will work...

I have a boat trailer where the rear most cross member is 2inch wide and 4inch tall. How can I work this with your U-bolts? Also it has 6 1/2inch clearance at the back so if I dont want it fragging all the time I have to be careful as to total...

I am looking at something like your UF48-979021 But they would need to mount on the rear of my featherlite aluminum trailer - model 4926 Any suggestions? Thanks | The Ultra-Fab Steel Micro Roller # UF48-979021 has a steel bracket that is designed...

2007 kz toy hauler 42 foot 5th wheel Spacing between factory brackets is 22 1/2inch would the ultra fab 12k jack bolt in without welding? | In order for a 'right out of the box' fit for the Ultra-Fab # UF17-943010 fifth wheel landing gear,...

I have a Cougar lite fifth wheel that Im wanting to install a hitch that can support a 300lb dirt bike. I know there is a lot of bouncing on the back of fifth wheels and I dont want to have it do damage to the trailer or fall off and hurt someone...

Can I use them on a 2016 heartland model 278st | Yes, you can use the Ultra-Fab Skid Wheels for Low-Profile RV's # UF48-979011 on your 2016 Heartland Sundance 278TS. These wheels are designed to mount to the RV's frame to help preventing dragging...

My 5th wheel has a wheel spacing of 13 1/2inch between the tires at center. What do you recommend? | Since the distance between your tires is larger at 13-1/2 inches the Super Grip Chock XL Wheel Stabilizers # UF21-001095 is what you'd need...

I am looking to replace a Lippert hitch I have on the back of my Shasta Phoenix 5th wheel. I want to carry either a generator/box in a carrier or possibly 2 e-bikes. The !!/4 Lippert model I have bolts to C channel welded to the frame. It...

I have a 1996 Carri-lite, Atwood landing gear. One of the landing legs the one on same side as motor-lead leg has stripped out gears and possibly the acme screw/worm screw is not good has wobble and give to it. I just want to replace the entire...

I recently had trouble with my landing gear. I replaced the gear box and ordered bevel gear rebuild kits for each leg. The legs are an unknown lippert component product. The gears in the legs are different where as the 16 tooth gear has a 5/8...

Each switch has four insulated color wires- Black goes to ground, Red goes to the motor, green and white? | We can get your stabilizer set up, and I can tell you where each of the four wires go for the Ultra-Fab Power Twin II Electric Stabilizer...

Can you you this on the lippert flex air pin box? Thanks | Yes, the Ultra-Fab 5th Wheel King Pin Tripod Stabilizer - Steel - 37" to 50" - 5,000 lbs # UF19-950001 will work as long as your pin box height is within 37 to 50 inches and the pin...

Im looking at the Phoenix UF38-944055 for my Featherlite car trailer that has two 4900 lbs axles. The heaviest vehicle on the trailer is a 6000 lbs Jeep. I realize this jack may be overkill, but Im ok with that. I want to be able to tow the...

I have a 22.5 ft, 3900 dry weight travel trailer and find backing it on to leveling blocks very difficult. If I use 4 leveling jacks, one for each corner, would I still need to use leveling blocks? | The # UF48-979002 feature oversized footplates...

what is the length of the bottom 2 bolts that hold the base. Jt strong arm attaches with 4 inch swing bolt. my bal lopro 2400 jacks just barley catch a thread and dont make it to the outside of nut | Actually if you are using the JT's Strongarm...

will this leveling system work on my 2021 Forest River R pod 202 | Yes, your 2021 Forest River R-Pod 202 is absolutely compatible with the Ultra-Fab stabilizers, which are the following part: - Ultra-Fab Power Twin II Electric Stabilizer with...

I have a 2009 Keystone Cougar fifth wheel and the lead leg with the above mentioned model number is not working. I changed the factory installed gearbox to a Lippert 276602 Venture Fifth Wheel Landing Gear Box. Will this part LC119102 work...

I have a 2017 Kawasaki KLR 650, that is around 395lbs. to 400lbs with no fuel in it. I am wanting to haul it on a 3,000+ mile round trip on the back of a 2017 Thor Motor Coach Gemini 23tr. I was told by the manufacture that the TW of the hitch...

Some states do not allow doubles but I saw one that attaches to the frame with a tag axel so it is a part of the trailer not a seperate trailer so not doubles as such do you know of anything like that ? | Having a motorcycle carrier mounted...

How much weight will this roller withstand? I have a 13K pound trailer dry that drags over inclines. Wondering if this wheel would help of if there is one that would be more heavy duty for my situation. | The Ultra-Fab Steel Mini-Roller for...

Your description of the tires this mount will accept mentioned something about a 5 on 5 wheel and that it would not fit. How can I tell if I have a 5 on 5? I have a 2006 Keystone 25foot trailer. Thanks. | The 5 on 5 wheel that you are referring...

Hello, I am interested in purchasing an electric trailer jack. My camper is about 7000 lbs. and was wondering what jack would be best for it. Thanks | For an electric a-frame jack I would recommend the Phoenix part # UF38-944040 as this has...

I have a sundowner house trailer with the dual Ultra Fab landing gears on it. The trailer weights 10k empty. I ordered the Ultra-Fab Power Twin II 30 / 22 Gear Motors wiring Harness Kit UF39-841702, but they dont seem to have enough power to...

The stock one are all bent they look very small the trailer is 32ft and 7100lbs empty I just purchased 7500 lbs jack they look big bought trailer used so I am not sure if the ones on it were to small Hope the one I bought are the right ones...